Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Rework irq_find_mapping() to return an both an irq_desc pointer,
optionally the virtual irq number, and rename the result to
__irq_resolve_mapping(). a new helper called irq_resolve_mapping()
is provided for code that doesn't need the virtual irq number.
irq_find_mapping() is also rewritten in terms of __irq_resolve_mapping().
Signed-off-by: Marc Zyngier <maz@kernel.org>
It is pretty odd that the radix tree uses RCU while the linear
portion doesn't, leading to potential surprises for the users,
depending on how the irqdomain has been created.
Fix this by moving the update of the linear revmap under
the mutex, and the lookup under the RCU read-side lock.
The mutex name is updated to reflect that it doesn't only
cover the radix-tree anymore.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Caching a virq number in the revmap is pretty inefficient, as
it means we will need to convert it back to either an irq_data
or irq_desc to do anything with it.
It is also a bit odd, as the radix tree does cache irq_data
pointers.
Change the revmap type to be an irq_data pointer instead of
an unsigned int, and preserve the current API for now.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Direct mappings are completely exclusive of normal mappings, meaning
that we can refactor the code slightly so that we can get rid of
the revmap_direct_max_irq field and use the revmap_size field
instead, reducing the size of the irqdomain structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Only a handful of old PPC systems are still using the old 'nomap'
variant of the irqdomain library. Move the associated definitions
behind a configuration option, which will allow us to make some
more radical changes.
Signed-off-by: Marc Zyngier <maz@kernel.org>
irq_linear_revmap() is supposed to be a fast path for domain
lookups, but it only exposes low-level details of the irqdomain
implementation, details which are better kept private.
The *overhead* between the two is only a function call and
a couple of tests, so it is likely that noone can show any
meaningful difference compared to the cost of taking an
interrupt.
Reimplement irq_linear_revmap() with irq_find_mapping()
in order to preserve source code compatibility, and
rename the internal field for a measure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Pull gpio updates from Bartosz Golaszewski:
- new driver for the Realtek Otto GPIO controller
- ACPI support for gpio-mpc8xxx
- edge event support for gpio-sch (+ Kconfig fixes)
- Kconfig improvements in gpio-ich
- fixes to older issues in gpio-mockup
- ACPI quirk for ignoring EC wakeups on Dell Venue 10 Pro 5055
- improve the GPIO aggregator code by using more generic interfaces
instead of reimplementing them in the driver
- convert the DT bindings for gpio-74x164 to yaml
- documentation improvements
- a slew of other minor fixes and improvements to GPIO drivers
* tag 'gpio-updates-for-v5.13-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (34 commits)
dt-bindings: gpio: add YAML description for rockchip,gpio-bank
gpio: mxs: remove useless function
dt-bindings: gpio: fairchild,74hc595: Convert to json-schema
gpio: it87: remove unused code
gpio: 104-dio-48e: Fix coding style issues
gpio: mpc8xxx: Add ACPI support
gpio: ich: Switch to be dependent on LPC_ICH
gpio: sch: Drop MFD_CORE selection
gpio: sch: depends on LPC_SCH
gpiolib: acpi: Add quirk to ignore EC wakeups on Dell Venue 10 Pro 5055
gpio: sch: Hook into ACPI GPE handler to catch GPIO edge events
gpio: sch: Add edge event support
gpio: aggregator: Replace custom get_arg() with a generic next_arg()
lib/cmdline: Export next_arg() for being used in modules
gpio: omap: Use device_get_match_data() helper
gpio: Add Realtek Otto GPIO support
dt-bindings: gpio: Binding for Realtek Otto GPIO
docs: kernel-parameters: Add gpio_mockup_named_lines
docs: kernel-parameters: Move gpio-mockup for alphabetic order
lib: bitmap: provide devm_bitmap_alloc() and devm_bitmap_zalloc()
...
Linus Walleij pointed out that ird_domain_add_simple() gained
additional functionality and can't be anymore replaced with
a simple conditional. In preparation to upgrade GPIO library
to use fwnode, introduce irq_domain_create_simple() API which is
functional equivalent to the existing irq_domain_add_simple(),
but takes a pointer to the struct fwnode_handle as a parameter.
While at it, amend documentation to mention irq_domain_create_*()
functions where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull irq updates from Thomas Gleixner:
"Generic interrupt and irqchips subsystem updates. Unusually, there is
not a single completely new irq chip driver, just new DT bindings and
extensions of existing drivers to accomodate new variants!
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM
optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups"
* tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling
driver core: platform: Add devm_platform_get_irqs_affinity()
ACPI: Drop acpi_dev_irqresource_disabled()
resource: Add irqresource_disabled()
genirq/affinity: Add irq_update_affinity_desc()
irqchip/gic-v3-its: Flag device allocation as proxied if behind a PCI bridge
irqchip/gic-v3-its: Tag ITS device as shared if allocating for a proxy device
platform-msi: Track shared domain allocation
irqchip/ti-sci-intr: Fix freeing of irqs
irqchip/ti-sci-inta: Fix printing of inta id on probe success
drivers/irqchip: Remove EZChip NPS interrupt controller
Revert "genirq: Add fasteoi IPI flow"
irqchip/hip04: Make IPIs use handle_percpu_devid_irq()
irqchip/bcm2836: Make IPIs use handle_percpu_devid_irq()
irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()
irqchip/gic, gic-v3: Make SGIs use handle_percpu_devid_irq()
irqchip/ocelot: Add support for Jaguar2 platforms
irqchip/ocelot: Add support for Serval platforms
irqchip/ocelot: Add support for Luton platforms
irqchip/ocelot: prepare to support more SoC
...
There is currently no way to convey the affinity of an interrupt
via irq_create_mapping(), which creates issues for devices that
expect that affinity to be managed by the kernel.
In order to sort this out, rename irq_create_mapping() to
irq_create_mapping_affinity() with an additional affinity parameter that
can be passed down to irq_domain_alloc_descs().
irq_create_mapping() is re-implemented as a wrapper around
irq_create_mapping_affinity().
No functional change.
Fixes: e75eafb9b0 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kurz <groug@kaod.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201126082852.1178497-2-lvivier@redhat.com
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
It appears that some HW is ugly enough that not all the interrupts
connected to a particular interrupt controller end up with the same
hierarchy depth (some of them are terminated early). This leaves
the irqchip hacker with only two choices, both equally bad:
- create discrete domain chains, one for each "hierarchy depth",
which is very hard to maintain
- create fake hierarchy levels for the shallow paths, leading
to all kind of problems (what are the safe hwirq values for these
fake levels?)
Implement the ability to cut short a single interrupt hierarchy
from a level marked as being disconnected by using the new
irq_domain_disconnect_hierarchy() helper.
The irqdomain allocation code will then perform the trimming
Signed-off-by: Marc Zyngier <maz@kernel.org>
PCI devices behind a VMD bus are not subject to interrupt remapping, but
the irq domain for VMD MSI cannot be distinguished from a regular PCI/MSI
irq domain.
Add a new domain bus token and allow it in the bus token check in
msi_check_reservation_mode() to keep the functionality the same once VMD
uses this token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Link: https://lore.kernel.org/r/20200826112332.954409970@linutronix.de
