ADMA is only available on controller instances that are connected to the
L3 interconnect and are bus mastering capable.
As the MMCHS_HL_HWINFO is in the module registers before omap registers
and sdhci registers, and the omap registers and sdhci registers can be
at different offsets depending on the SoC, let's read MMCHS_HL_HWINFO
directly.
Let's also switch to using device_property_present() while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-6-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to support the legacy ti,non-removable property too. Let's warn
about the legacy property and mark the device as non-removable.
Naturally all the mainline kernel devicetree files will get updated to use
the standard non-removable property with the sdhci-omap conversion. But we
also have folks updating their kernels with custom devicetree files that
we need to consider.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-5-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysconfig register is managed in a generic way by PM runtime for us by
the interconnect target module layer code. SDHCI_RESET_ALL also resets the
target module configuration, so we need to restore sysconfig after reset.
Note that there is no need to save and restore sysconfig during PM runtime,
the PM runtime layer will do that for us.
Not sure if this issue is a problem with the current configurations, I
noticed the issue while adding support for older TI SoCs and testing with
wlcore SDIO wlan device.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-4-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d3 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to JEDEC Spec, there is no need to do tuning under HS400 mode
since the Rx signal is aligned with the DS signal. However, MediaTek's IC
need set its "DS delay" internally to ensure it can latch Rx signal
correctly.
In previous version, We provide an "hs400-ds-delay" in device tree to cover
different chipset/PCB design, and it works fine in most cases. But, with
the development of process technology and the big VCore voltage scale
range(may have 0.7V/0.6V/0.55V), it is difficult to find a suitable
"hs400-ds-delay" to cover all of IC corner cases(SSSS/TTTT/FFFF). So that
We must have the ability to do hs400 online tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds a ->execute_hs400_tuning() host callback to enable optional
support for host specific tuning for eMMC HS400 mode. Additionally, share
mmc_get_ext_csd() through the public host headerfile, to allow it to be
used by the host drivers, which is needed to support the HS400 tuning.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Link: https://lore.kernel.org/r/20210917124803.22871-3-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We never checked for errors on add_disk() as this function returned void.
Now that this is fixed, use the shiny new error handling.
The caller only cleanups the disk if we pass on an allocated md but on
error we return return ERR_PTR(ret), and so we must do all the unwinding
ourselves.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210830212538.148729-5-mcgrof@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 285133040e
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 103a5348c2 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
