In the cpuidle-psci case, runtime PM in combination with the generic PM
domain (genpd), may be used when entering/exiting a shared idlestate. More
precisely, genpd relies on runtime PM to be enabled for the attached device
(in this case it belongs to a CPU), to properly manage the reference
counting of its PM domain.
This works fine most of the time, but during system suspend in
dpm_suspend_late(), the PM core disables runtime PM for all devices. Beyond
this point, calls to pm_runtime_get_sync() to runtime resume a device may
fail and therefore it could also mess up the reference counting in genpd.
To fix this problem, let's call wake_up_all_idle_cpus() in
dpm_suspend_late(), prior to disabling runtime PM. In this way a device
that belongs to a CPU, becomes runtime resumed through cpuidle-psci and
stays like that, because the runtime PM usage count has been bumped in
device_prepare().
Diagnosed-by: Maulik Shah <mkshah@codeaurora.org>
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge updates related to system sleep for 5.16-rc1:
- Clean up hib_wait_io() (Falla Coulibaly).
- Fix sparse warnings in hibernation-related code (Anders Roxell).
- Use vzalloc() and kzalloc() instead of their open-coded
equivalents in hibernation-related code (Cai Huoqing).
- Prevent user space from crashing the kernel by attempting to
restore the system state from a swap partition in use (Ye Bin).
- Do not let "syscore" devices runtime-suspend during system PM
transitions (Rafael Wysocki).
- Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).
- Pause cpuidle later and resume it earlier during system PM
transitions (Rafael Wysocki).
- Make system suspend code use valid_state() consistently (Rafael
Wysocki).
- Add support for enabling wakeup IRQs after invoking the
->runtime_suspend() callback and make two drivers use it (Chunfeng
Yun).
* pm-sleep:
usb: mtu3: enable wake-up interrupt after runtime_suspend called
usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
PM / wakeirq: support enabling wake-up irq after runtime_suspend called
PM: suspend: Use valid_state() consistently
PM: sleep: Pause cpuidle later and resume it earlier during system transitions
PM: suspend: Do not pause cpuidle in the suspend-to-idle path
PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
PM: hibernate: Get block device exclusively in swsusp_check()
PM: hibernate: swap: Use vzalloc() and kzalloc()
PM: hibernate: fix sparse warnings
Revert "PM: sleep: Do not assume that "mem" is always present"
PM: hibernate: Remove blk_status_to_errno in hib_wait_io
PM: sleep: Do not assume that "mem" is always present
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 8651f97bd9 ("PM / cpuidle: System resume hang fix with
cpuidle") that introduced cpuidle pausing during system suspend
did that to work around a platform firmware issue causing systems
to hang during resume if CPUs were allowed to enter idle states
in the system suspend and resume code paths.
However, pausing cpuidle before the last phase of suspending
devices is the source of an otherwise arbitrary difference between
the suspend-to-idle path and other system suspend variants, so it is
cleaner to do that later, before taking secondary CPUs offline (it
is still safer to take secondary CPUs offline with cpuidle paused,
though).
Modify the code accordingly, but in order to avoid code duplication,
introduce new wrapper functions, pm_sleep_disable_secondary_cpus()
and pm_sleep_enable_secondary_cpus(), to combine cpuidle_pause()
and cpuidle_resume(), respectively, with the handling of secondary
CPUs during system-wide transitions to sleep states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
It is pointless to pause cpuidle in the suspend-to-idle path,
because it is going to be resumed in the same path later and
pausing it does not serve any particular purpose in that case.
Rework the code to avoid doing that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes: 057d51a126 ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull xen fixes from Juergen Gross:
- The first hunk of a Xen swiotlb fixup series fixing multiple minor
issues and doing some small cleanups
- Some further Xen related fixes avoiding WARN() splats when running as
Xen guests or dom0
- A Kconfig fix allowing the pvcalls frontend to be built as a module
* tag 'for-linus-5.15b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
swiotlb-xen: drop DEFAULT_NSLABS
swiotlb-xen: arrange to have buffer info logged
swiotlb-xen: drop leftover __ref
swiotlb-xen: limit init retries
swiotlb-xen: suppress certain init retries
swiotlb-xen: maintain slab count properly
swiotlb-xen: fix late init retry
swiotlb-xen: avoid double free
xen/pvcalls: backend can be a module
xen: fix usage of pmd_populate in mremap for pv guests
xen: reset legacy rtc flag for PV domU
PM: base: power: don't try to use non-existing RTC for storing data
xen/balloon: use a kernel thread instead a workqueue
There are variables(power.may_skip_resume and dev->power.must_resume)
and DPM_FLAG_MAY_SKIP_RESUME flags to control the resume of devices after
a system wide suspend transition.
Setting the DPM_FLAG_MAY_SKIP_RESUME flag means that the driver allows
its "noirq" and "early" resume callbacks to be skipped if the device
can be left in suspend after a system-wide transition into the working
state. PM core determines that the driver's "noirq" and "early" resume
callbacks should be skipped or not with dev_pm_skip_resume() function by
checking power.may_skip_resume variable.
power.must_resume variable is getting set to false in __device_suspend()
function without checking device's DPM_FLAG_MAY_SKIP_RESUME settings.
In problematic scenario, where all the devices in the suspend_late
stage are successful and some device can fail to suspend in
suspend_noirq phase. So some devices successfully suspended in suspend_late
stage are not getting chance to execute __device_suspend_noirq()
to set dev->power.must_resume variable to true and not getting
resumed in early_resume phase.
Add a check for device's DPM_FLAG_MAY_SKIP_RESUME flag before
setting power.must_resume variable in __device_suspend function.
Fixes: 6e176bf8d4 ("PM: sleep: core: Do not skip callbacks in the resume phase")
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function has the 'irq' parameter which isn't ever used, so drop it.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull clk updates from Stephen Boyd:
"Nothing changed in the clk framework core this time around. We did get
some updates to the basic clk types to use determine_rate for the
divider type and add a power of two fractional divider flag though.
Otherwise, this is a collection of clk driver updates. More than half
the diffstat is in the Qualcomm clk driver where we add a bunch of
data to describe clks on various SoCs and fix bugs. The other big new
thing in here is the Mediatek MT8192 clk driver. That's been under
review for a while and it's nice to see that it's finally upstream.
Beyond that it's the usual set of minor fixes and tweaks to clk
drivers. There are some non-clk driver bits in here which have all
been acked by the respective maintainers.
New Drivers:
- Support video, gpu, display clks on qcom sc7280 SoCs
- GCC clks on qcom MSM8953, SM4250/6115, and SM6350 SoCs
- Multimedia clks (MMCC) on qcom MSM8994/MSM8992
- RPMh clks on qcom SM6350 SoCs
- Support for Mediatek MT8192 SoCs
- Add display (DU and DSI) clocks on Renesas R-Car V3U
- Add I2C, DMAC, USB, sound (SSIF-2), GPIO, CANFD, and ADC clocks and
resets on Renesas RZ/G2L
Updates:
- Support the SD/OE pin on IDT VersaClock 5 and 6 clock generators
- Add power of two flag to fractional divider clk type
- Migrate some clk drivers to clk_divider_ops.determine_rate
- Migrate to clk_parent_data in gcc-sdm660
- Fix CLKOUT clocks on i.MX8MM and i.MX8MN by using imx_clk_hw_mux2
- Switch from .round_rate to .determine_rate in clk-divider-gate
- Fix clock tree update for TF-A controlled clocks for all i.MX8M
- Add missing M7 core clock for i.MX8MN
- YAML conversion of rk3399 clock controller binding
- Removal of GRF dependency for the rk3328/rk3036 pll types
- Drop CLK_IS_CRITICAL flag from Tegra fuse clk
- Make CLK_R9A06G032 Kconfig symbol invisible
- Convert various DT bindings to YAML"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (128 commits)
dt-bindings: clock: samsung: fix header path in example
clk: tegra: fix old-style declaration
clk: qcom: Add SM6350 GCC driver
MAINTAINERS: clock: include S3C and S5P in Samsung SoC clock entry
dt-bindings: clock: samsung: convert S5Pv210 AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos AudSS to dtschema
dt-bindings: clock: samsung: convert Exynos4 to dtschema
dt-bindings: clock: samsung: convert Exynos3250 to dtschema
dt-bindings: clock: samsung: convert Exynos542x to dtschema
dt-bindings: clock: samsung: add bindings for Exynos external clock
dt-bindings: clock: samsung: convert Exynos5250 to dtschema
clk: vc5: Add properties for configuring SD/OE behavior
clk: vc5: Use dev_err_probe
dt-bindings: clk: vc5: Add properties for configuring the SD/OE pin
dt-bindings: clock: brcm,iproc-clocks: fix armpll properties
clk: zynqmp: Fix kernel-doc format
clk: at91: clk-generated: Limit the requested rate to our range
clk: ralink: avoid to set 'CLK_IS_CRITICAL' flag for gates
clk: zynqmp: Fix a memory leak
clk: zynqmp: Check the return type
...
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
If CONFIG_PM_OPP=n, of_get_required_opp_performance_state() always
returns -EOPNOTSUPP, and all drivers for devices that are part of a PM
Domain fail to probe with:
failed to set required performance state for power-domain foo: -95
probe of bar failed with error -95
Fix this by treating -EOPNOTSUPP the same as -ENODEV.
Fixes: c016baf7dc ("PM: domains: Add support for 'required-opps' to set default perf state")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A typical code pattern for pm_clk_create() call is to call it in the
_probe function and to call pm_clk_destroy() both from _probe error path
and from _remove function. For some drivers the whole remove function
would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_clk_create() removes the need for calling pm_clk_destroy() both
in the probe()'s error path and in the remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-3-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A typical code pattern for pm_runtime_enable() call is to call it in the
_probe function and to call pm_runtime_disable() both from _probe error
path and from _remove function. For some drivers the whole remove
function would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_runtime_enable() removes the need for calling
pm_runtime_disable() both in the probe()'s error path and in the
remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210731195034.979084-2-dmitry.baryshkov@linaro.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
GENPD core doesn't support handling performance state changes while
consumer device is runtime-suspended or when runtime PM is disabled.
GENPD core may override performance state that was configured by device
driver while RPM of the device was disabled or device was RPM-suspended.
Let's close that gap by allowing drivers to control performance state
while RPM of a consumer device is disabled and to set up performance
state of RPM-suspended device that will be applied by GENPD core on
RPM-resume of the device.
Fixes: 5937c3ce21 ("PM: domains: Drop/restore performance state votes for devices at runtime PM")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices within power domains with performance states do not
support DVFS, but still need to vote on a default/static state
while they are active. They can express this using the 'required-opps'
property in device tree, which points to the phandle of the OPP
supported by the corresponding power-domains.
Add support to parse this information from DT and then set the
specified performance state during attach and drop it on detach.
runtime suspend/resume callbacks already have logic to drop/set
the vote as needed and should take care of dropping the default
perf state vote on runtime suspend and restore it back on runtime
resume.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: qcom: Add SPM register data for MSM8226
dt-bindings: arm: msm: Add SAW2 for MSM8226
* pm-sleep:
PM: sleep: Use ktime_us_delta() in initcall_debug_report()
* pm-domains:
PM: domains: Shrink locking area of the gpd_list_lock
Use ktime_us_delta() to make the debug log more precise instead of
shifting the return value of ktime_to_ns() applied to a ktime_sub()
result by 10 bit positions to the right.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
[ rjw: Changelog rewrite, subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
