Add a flag to the API so users can indicate they want
silent operations. This is needed because silent ops
cannot be used with USE_ONCE MRs, so we can't just
assume silent.
Also, change send_xmit to do atomic op before rdma op if
both are present, and centralize the hairy logic to determine if
we want to attempt silent, or not.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Implement a CMSG-based interface to do FADD and CSWP ops.
Alter send routines to handle atomic ops.
Add atomic counters to stats.
Add xmit_atomic() to struct rds_transport
Inline rds_ib_send_unmap_rdma into unmap_rm
Signed-off-by: Andy Grover <andy.grover@oracle.com>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct state range of PHY bus addresses (i.e. 0-31) in comment,
make spelling of PHY consistent in comments.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- napi_gro_flush() is exported from net/core/dev.c, to avoid
an irq_save/irq_restore in the packet receive path.
- use napi_gro_receive() instead of netif_receive_skb()
- use napi_gro_flush() before calling __napi_complete()
- turn on NETIF_F_GRO by default
- Tested on a Marvell 88E8001 Gigabit NIC
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As some driver authors seem to reintroduce dev->last_rx use,
add a comment to strongly discourage this.
Since commit 6cf3f41e6c (bonding, net: Move last_rx update into bonding
recv logic), network drivers dont need to update last_rx themselves,
unless they use this field to implement a timeout.
Not updating last_rx helps not dirtying a cache line, improving
performance in SMP.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a "user timeout" support as described in RFC793. The
socket option is also needed for the the local half of RFC5482 "TCP User
Timeout Option".
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int,
when > 0, to specify the maximum amount of time in ms that transmitted
data may remain unacknowledged before TCP will forcefully close the
corresponding connection and return ETIMEDOUT to the application. If
0 is given, TCP will continue to use the system default.
Increasing the user timeouts allows a TCP connection to survive extended
periods without end-to-end connectivity. Decreasing the user timeouts
allows applications to "fail fast" if so desired. Otherwise it may take
upto 20 minutes with the current system defaults in a normal WAN
environment.
The socket option can be made during any state of a TCP connection, but
is only effective during the synchronized states of a connection
(ESTABLISHED, FIN-WAIT-1, FIN-WAIT-2, CLOSE-WAIT, CLOSING, or LAST-ACK).
Moreover, when used with the TCP keepalive (SO_KEEPALIVE) option,
TCP_USER_TIMEOUT will overtake keepalive to determine when to close a
connection due to keepalive failure.
The option does not change in anyway when TCP retransmits a packet, nor
when a keepalive probe will be sent.
This option, like many others, will be inherited by an acceptor from its
listener.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Allow setting
the ethertype for the protocol when a driver has
support for this. The default if unspecified is
EAP, of course.
Note: This is suitable only for station mode, not
for AP implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
compare_ether_header() can have a special implementation on 64 bit
arches if CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined.
__napi_gro_receive() and vlan_gro_common() can avoid a conditional
branch to perform device match.
On x86_64, __napi_gro_receive() has now 38 instructions instead of 53
As gcc-4.4.3 still choose to not inline it, add inline keyword to this
performance critical function.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids unnecessary casting and adds the ioaddr in the
private structure.
This patch also removes many warning when compile the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial extension to existing meta data match rules to allow
matching on skb receive hash value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nl80211 documentation is currently never
generated, so problems have accumulated. Fix
most of the trivial ones.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IFF_OVS_DATAPATH is a place-holder for the Open vSwitch datapath
which I am preparing to submit for merging.
As all 16 bits of priv_flags are already assigned flags, also increase
the size of priv_flags to 32 bits.
Unfortunately, by my calculations this increases the size of
struct net_device by 4 bytes on 32bit architectures and
8 bytes on 64 bit architectures. I couldn't see an obvious
way to avoid that.
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is patch 1/6 which contains linux driver source for
Brocade's BR1010/BR1020 10Gb CEE capable ethernet adapter.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
