DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Pull ACPI updates from Rafael Wysocki:
"These are usual ACPICA code updates (although there are more of them
than in the last few releases), a noticeable EC driver update (which
mostly consists of cleanups, though), the device enumeration quirks
handling rework from Hans, some updates eliminating unnecessary CPU
cache flushing in some places (processor idle and system-wide PM code)
and a bunch of assorted cleanups and fixes.
Specifics:
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
- iASL/Disassembler: Additional support for NHLT table (Bob
Moore).
- Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
- Fix a couple of warnings under MSVC (Bob Moore).
- iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
- iASL/NHLT table: "Specific Data" field support (Bob Moore).
- Use original data_table_region pointer for accesses (Jessica
Clarke).
- Use original pointer for virtual origin tables (Jessica Clarke).
- Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
- Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
- iASL: Add suppport for AGDI table (Ilkka Koskinen).
- Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
- Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
- Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
- Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
- Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
- Fix wrong interpretation of PCC address (Sudeep Holla).
- Add support for PCC Opregion special context data (Sudeep
Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system PM
transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang
Li).
- Rework flushing of EC work while suspended to idle and clean up the
handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used when
the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh)"
* tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
ACPI: processor: thermal: avoid cpufreq_get_policy()
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
ACPI: battery: Add the ThinkPad "Not Charging" quirk
ACPI: sysfs: use default_groups in kobj_type
ACPICA: Update version to 20211217
ACPICA: iASL/NHLT table: "Specific Data" field support
ACPICA: iASL: Add suppport for AGDI table
ACPICA: iASL: Add TDEL table to both compiler/disassembler
ACPICA: Fixed a couple of warnings under MSVC
ACPICA: Change a return_ACPI_STATUS (AE_BAD_PARAMETER)
ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
ACPICA: Add support for PCC Opregion special context data
ACPICA: Fix wrong interpretation of PCC address
...
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: ov5693
- A new driver for STM32 Chrom-ART Accelerator
- Added V4L2 core helper functions for VP9 codec
- Hantro driver has gained support for VP9 codecs
- Added support for Maxim MAX96712 Quad GMSL2 Deserializer
- The staging atomisp driver has gained lots of improvements, fixes and
cleanups. It now works with userptr
- Lots of random driver improvements as usual
* tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (397 commits)
media: ipu3-cio2: Add support for instantiating i2c-clients for VCMs
media: ipu3-cio2: Call cio2_bridge_init() before anything else
media: ipu3-cio2: Defer probing until the PMIC is fully setup
media: hantro: Add support for Allwinner H6
media: dt-bindings: allwinner: document H6 Hantro G2 binding
media: hantro: Convert imx8m_vpu_g2_irq to helper
media: hantro: move postproc enablement for old cores
media: hantro: vp9: add support for legacy register set
media: hantro: vp9: use double buffering if needed
media: hantro: add support for reset lines
media: hantro: Fix probe func error path
media: i2c: hi846: use pm_runtime_force_suspend/resume for system suspend
media: i2c: hi846: check return value of regulator_bulk_disable()
media: hi556: Support device probe in non-zero ACPI D state
media: ov5675: Support device probe in non-zero ACPI D state
media: imx208: Support device probe in non-zero ACPI D state
media: ov2740: support device probe in non-zero ACPI D state
media: ov5670: Support device probe in non-zero ACPI D state
media: ov8856: support device probe in non-zero ACPI D state
media: ov8865: Disable only enabled regulators on error path
...
Pull ARM SoC updates from Arnd Bergmann:
"These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols, the
MAINTAINERS file, and removing some dead code"
* tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: exynos: Enable Exynos Multi-Core Timer driver
ARM: ixp4xx: remove unused header file pata_ixp4xx_cf.h
ARM: ixp4xx: remove dead configs CPU_IXP43X and CPU_IXP46X
MAINTAINERS: Add Florian as BCM5301X and BCM53573 maintainer
ARM: samsung: Remove HAVE_S3C2410_I2C and use direct dependencies
ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART
ARM: imx: remove dead left-over from i.MX{27,31,35} removal
ARM: s3c: add one more "fallthrough" statement in Jive
ARM: s3c: include header for prototype of s3c2410_modify_misccr
ARM: shmobile: rcar-gen2: Add missing of_node_put()
Merge ACPI device enumeration updates, ACPI power management updates
and PCI host bridge ACPI driver updates for 5.17-rc1:
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
* acpi-scan:
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
ACPI: Use acpi_fetch_acpi_dev() instead of acpi_bus_get_device()
ACPI: scan: Introduce acpi_fetch_acpi_dev()
ACPI: scan: Do not add device IDs from _CID if _HID is not valid
* acpi-pm:
ACPI: PM: Remove redundant cache flushing
ACPI: PM: Avoid CPU cache flush when entering S4
* acpi-power:
ACPI: PM: Emit debug messages when enabling/disabling wakeup power
* acpi-pci:
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
When performing an I2C transfer where the last message was a write KASAN
would complain:
BUG: KASAN: slab-out-of-bounds in mpc_i2c_do_action+0x154/0x630
Read of size 2 at addr c814e310 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G B 5.16.0-rc8 #1
Call Trace:
[e5ee9d50] [c08418e8] dump_stack_lvl+0x4c/0x6c (unreliable)
[e5ee9d70] [c02f8a14] print_address_description.constprop.13+0x64/0x3b0
[e5ee9da0] [c02f9030] kasan_report+0x1f0/0x204
[e5ee9de0] [c0c76ee4] mpc_i2c_do_action+0x154/0x630
[e5ee9e30] [c0c782c4] mpc_i2c_isr+0x164/0x240
[e5ee9e60] [c00f3a04] __handle_irq_event_percpu+0xf4/0x3b0
[e5ee9ec0] [c00f3d40] handle_irq_event_percpu+0x80/0x110
[e5ee9f40] [c00f3e48] handle_irq_event+0x78/0xd0
[e5ee9f60] [c00fcfec] handle_fasteoi_irq+0x19c/0x370
[e5ee9fa0] [c00f1d84] generic_handle_irq+0x54/0x80
[e5ee9fc0] [c0006b54] __do_irq+0x64/0x200
[e5ee9ff0] [c0007958] __do_IRQ+0xe8/0x1c0
[c812dd50] [e3eaab20] 0xe3eaab20
[c812dd90] [c0007a4c] do_IRQ+0x1c/0x30
[c812dda0] [c0000c04] ExternalInput+0x144/0x160
--- interrupt: 500 at arch_cpu_idle+0x34/0x60
NIP: c000b684 LR: c000b684 CTR: c0019688
REGS: c812ddb0 TRAP: 0500 Tainted: G B (5.16.0-rc8)
MSR: 00029002 <CE,EE,ME> CR: 22000488 XER: 20000000
GPR00: c10ef7fc c812de90 c80ff200 c2394718 00000001 00000001 c10e3f90 00000003
GPR08: 00000000 c0019688 c2394718 fc7d625b 22000484 00000000 21e17000 c208228c
GPR16: e3e99284 00000000 ffffffff c2390000 c001bac0 c2082288 c812df60 c001ba60
GPR24: c23949c0 00000018 00080000 00000004 c80ff200 00000002 c2348ee4 c2394718
NIP [c000b684] arch_cpu_idle+0x34/0x60
LR [c000b684] arch_cpu_idle+0x34/0x60
--- interrupt: 500
[c812de90] [c10e3f90] rcu_eqs_enter.isra.60+0xc0/0x110 (unreliable)
[c812deb0] [c10ef7fc] default_idle_call+0xbc/0x230
[c812dee0] [c00af0e8] do_idle+0x1c8/0x200
[c812df10] [c00af3c0] cpu_startup_entry+0x20/0x30
[c812df20] [c001e010] start_secondary+0x5d0/0xba0
[c812dff0] [c00028a0] __secondary_start+0x90/0xdc
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional() for DT users only.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
x86 ACPI devices which ship with only Android as their factory image
usually declare a whole bunch of bogus I2C devices in their ACPI tables.
Instantiating I2C clients for these bogus devices causes various issues,
e.g. GPIO/IRQ resource conflicts because sometimes drivers do bind to them.
The Android x86 kernel fork shipped on these devices has some special code
to remove these bogus devices, instead of just fixing the DSDT <sigh>.
Use the new acpi_quirk_skip_i2c_client_enumeration() helper to identify
known boards / acpi devices with this issue, and skip enumerating these.
Note these boards typically do actually have I2C devices, just
different ones then the ones described in their DSDT. The devices
which are actually present are manually instantiated by the
drivers/platform/x86/x86-android-tablets.c kernel module.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No symbols from the linux/irqchip/chained_irq.h and linux/irqdomain.h
headers are used in the driver, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the DMA setup and callback
were superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the interrupt handlers was
superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rafał Miłecki
Wolfram Sang
Vladimir Zapolskiy
Eric Anholt
Linus Torvalds
Michael S. Tsirkin
Yang Li
Rafael J. Wysocki
Chris Packham
Lad Prabhakar
Pavel Skripkin
Hans de Goede
Thierry Reding
Wolfram Sang