Input signals can be steered to any of the frequency counters.
The counter measures the frequency over a number of seconds:
echo 0 > freq1/seconds = turns off measurement
echo 1 > freq1/seconds = sets period & turns on measurment.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The signal generators can be programmed either via the sysfs
file or through a PTP_CLK_REQ_PEROUT ioctl request.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware provides 4 programmable signal generators, add
support for those here. The signal generators provide the
ability to set the period, duty cycle, phase offset, and polarity,
with new values defaulting to prior values.
The period and phase offset are specified in nanoseconds.
E.g: period [duty [phase [polarity]]]
echo 500000000 > signal # 1/2 second period
echo 1000000 40 100 > signal # 1ms period, 40% on, offset 100ns
echo 0 > signal # turn off generator
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to group sysfs nodes behind a firmware feature
check. This way non-present sysfs attributes are omitted on
older firmware, which does not have newer features.
This will be used in the upcoming patches which adds more
features to the timecard.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As there are may be 2 GNSS outputs, rename the first one for clarity.
This also works around a parsing issue when specifying selectors.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the "IN: None" selector, which disables
the input on a sma pin. This should be compatible with old firmware
(the firmware will ignore it if not supported).
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assuming the firmware allows it, the direction of each SMA connector
is no longer fixed. Handle remapping directions for each pin.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial port driver attempts to test for correct THRE behavior
on startup. However, it does this by disabling interrupts, and
then intentionally trying to trigger an interrupt in order to see
if the IIR bit is set in the UART.
However, in this FPGA design, the UART interrupt is generated
through the MSI vector, so when interrupts are re-enabled after
the test, the DMAR-IR reports an unhandled IRTE entry, since
no irq handler is installed at this point - it is installed
after the test.
This only happens on the /second/ open of the UART, since on the
first open, the x86_vector has installed and activated by the
driver probe, and is correctly handled. When the serial port is
closed for the first time, this vector is deactivated and removed,
leading to this error.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220309223427.34745-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cache the firmware version when the card is initialized,
and use this field to populate the devlink firmware information.
The cached firmware version will be used for feature gating in
upcoming patches.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the at24 drivers for the eeprom, and use the accessors
via the nvmem API instead of direct i2c accesses. This makes
things cleaner.
Add an eeprom map table which specifies where the pre-defined
information is located. Retrieve the information and and export
it via the devlink interface.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
utc_tai_offset is used to correct IRIG, DCF and NMEA outputs and is
set during initialisation but is not corrected during leap second
announce event. Add watchdog code to control this correction.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TOD correction register is used to compensate for leap seconds in
different domains. Export it as an attribute with write access.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Monitoring of clock variance could be done through checking
the offset and the drift updates that are applied to atomic
clocks. Expose these values as attributes for the timecard.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TOD information is currently displayed only on module load,
which doesn't provide updated information as the system runs.
Create a debug file which provides the current TOD status information,
and move the information display there.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Lemon
Dan Carpenter
Jonathan Lemon
Min Li
Jakub Kicinski
Vadim Fedorenko