On device initialization, wait till firmware indicates that that it is done
with initialization before proceeding to initialize the device.
Also update initialization segment layout to match driver/firmware
interface definitions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement the pci_error_handlers for mlx5_core which allow the
driver to recover from PCI error.
Once an error is detected in the PCI, the mlx5_pci_err_detected is called
and it:
1) Marks the device to be in 'Internal Error' state.
2) Dispatches an event to the mlx5_ib to flush all the outstanding cqes
with error.
3) Returns all the on going commands with error.
4) Unloads the driver.
Afterwards, the FW is reset and mlx5_pci_slot_reset is called and it
enables the device and restore it's pci state.
If the later succeeds, mlx5_pci_resume is called, and it loads the SW
stack.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detection of a fatal condition has been updated to take into account
the state reported by the device or by detecting an all ones read of the
firmware version which indicates that the device is not accessible.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a single threaded work queue for each device in the system instead of
using one thread for any device. This is required so we can concurrently
process system error handling for all the devices that need that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to handling system errors at the mlx5_core level, change the
interface of cmd_work_handler to accept a 64 bit argument for the vector.
This allows to encode a flag that signifies when the handler is called
as a result of a driver logic that wishes to terminate commands that
the hardware may not be able to terminate. Such command completions
are detected at the handler and proper return status is encoded.
To be able to terminate page handler commands, we make sure to set
the corresponding bit in the bitmask.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 96249d70dd ("IB/core: Guarantee that a local_dma_lkey
is available") allows ULPs that make use of the local dma key to keep
working as before by allocating a DMA MR with local permissions and
converted these consumers to use the MR associated with the PD
rather then device->local_dma_lkey.
ConnectIB has some known issues with memory registration
using the local_dma_lkey (SEND, RDMA, RECV seems to work ok).
Thus don't expose support for it (remove device->local_dma_lkey
setting), and take advantage of the above commit such that no regression
is introduced to working systems.
The local_dma_lkey support will be restored in CX4 depending on FW
capability query.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
The mlx5 driver exposes device capability IB_DEVICE_LOCAL_DMA_LKEY
but does not set the the device local_dma_lkey. This breaks
rpcrdma drivers.
Query and set this lkey when creating the device resources.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A regular TX WQE execution involves two or more DMA reads -
one to fetch the WQE, and another one per WQE gather entry.
These DMA reads obviously increase the TX latency.
There are two mlx5 mechanisms to bypass these DMA reads:
1) Inline WQE
2) Blue Flame (BF)
An inline WQE contains a whole packet, thus saves the DMA read/s
of the regular WQE gather entry/s. Inline WQE support was already
added in the previous commit.
A BF WQE is written directly to the device I/O mapped memory, thus
enables saving the DMA read that fetches the WQE.
The BF WQE I/O write must be in cache line granularity, thus uses
the CPU write combining mechanism.
A BF WQE I/O write acts also as a TX doorbell for notifying the
device of new TX WQEs.
A BF WQE is written to the same I/O mapped address as the regular TX
doorbell, thus this address is being mapped twice - once by ioremap()
and once by io_mapping_map_wc().
While both mechanisms reduce the TX latency, they both consume more CPU
cycles than a regular WQE:
- A BF WQE must still be written to host memory, in addition to being
written directly to the device I/O mapped memory.
- An inline WQE involves copying the SKB data into it.
To handle this tradeoff, we introduce here a heuristic algorithm that
strives to avoid using these two mechanisms in case the TX queue is
being back-pressured by the device, and limit their usage rate otherwise.
An inline WQE will always be "Blue Flamed" (written directly to the
device I/O mapped memory) while a BF WQE may not be inlined (may contain
gather entries).
Preliminary testing using netperf UDP_RR shows that the latency goes down
from 17.5us to 16.9us, while the message rate (tested with pktgen) stays
the same.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By affinity hints and XPS, each mlx5e channel is assigned a CPU
core.
Channel DMA coherent memory that is written by the NIC and read
by SW (e.g CQ buffer) is allocated on the NUMA node of the CPU
core assigned for the channel.
Channel DMA coherent memory that is written by SW and read by the
NIC (e.g SQ/RQ buffer) is allocated on the NUMA node of the NIC.
Doorbell record (written by SW and read by the NIC) is an
exception since it is accessed by SW more frequently.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
