Alignment should always match open parenthesis.
Also remove two unnecessary blank lines
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use sizeof where possible to ensure we don't read/write more than the
allocated buffer.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds1307->regs is never used before being read or initialized locally. There
is no point in keeping a copy in memory.
Also limit the size of the read buffer to what is really used, rename buf
to regs for consistency and use sizeof() where possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Based on QNAP's arch/arm/mach-rtk119x/driver/rtk_rtc_drv.c code and
mach-rtk119x/driver/dc2vo/fpga/include/mis_reg.h register definitions.
The base year 2014 was observed on all of Zidoo X9S, ProBox2 Ava and
Beelink Lake I.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC can output its 32kHz clock outside of the SoC, for example to clock
a WiFi chip.
Create a new clock that other devices will be able to retrieve, while
maintaining the DT stability by providing a default name for that clock if
clock-output-names doesn't list one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support for reading and writing date/time from/to ds1341 chip.
ds1341 chip has other features - alarms, input clock (can be used instead
of intercal oscillator for better accuracy), output clock ("square wave
generation"). However, not all of that is available at the same time.
Same chip pins, CLKIN/nINTA and SQW/nINTB, can be used either for
input/output clocks, or for alarm interrupts. Role of these pins on
particular board depends on hardware wiring.
We can add device tree properties that describe if each of pins is wired
as clock, or as interrupt, or left unconnected, and enable support for
corresponding functionality based on that. But that is cumbersome, requires
hardware for testing, and has to deal with bit enabling/disabling output
clock also affects which pins alarm interrupts are routed to.
Another factor is that there are hardware setups (i.e. ZII RDU2) that
power DS1341 from SuperCap, which makes power saving critical. For such
setups, kernel driver should leave register bits that control mentioned
pins in the state configured by bootloader.
Given all that, it was decided to limit support to "only date/time" for
now. That is enough for common use case. Full (and cumbersome)
implementation can be added later if ever needed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove member nvram_offset from struct ds1307 and use the value stored
in struct chip_desc directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Change the usage of variable want_irq to reflect its name. Don't set
it to true in case wakeup is enabled but no interrupt number is given.
In addition set variable ds1307_can_wakeup_device if chip->alarm
is set only.
This allows to simplify the code and make it better understandable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of storing the trickle_charger_setup value in struct chip_desc
we can let function ds1307_trickle_init return it because it's used
in the probe function only.
This allows us to constify struct chip_desc variables in a next step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RK808 and RK805 PMICs are using a similar register map.
We can reuse the rtc driver for the RK805 PMIC. So let's add
the RK805 in the Kconfig description.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
