Misc updates from mlx5-next branch:
1) Add the required HW definitions and structures for upcoming TLS
support.
2) Add support for MCQI and MCQS hardware registers for fw version query.
3) Added hardware bits and structures definitions for sub-functions
4) Small code cleanup and improvement for PF pci driver.
5) Bluefield (ECPF) updates and refactoring for better E-Switch
management on ECPF embedded CPU NIC:
5.1) Consolidate querying eswitch number of VFs
5.2) Register event handler at the correct E-Switch init stage
5.3) Setup PF's inline mode and vlan pop when the ECPF is the
E-Swtich manager ( the host PF is basically a VF ).
5.4) Handle Vport UC address changes in switchdev mode.
6) Cleanup the rep and netdev reference when unloading IB rep.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
i# All conflicts fixed but you are still merging.
Use the reported device capabilities for the supported user events (i.e.
affiliated and un-affiliated) to set the EQ mask.
As the event mask can be up to 256 defined by 4 entries of u64 change
the applicable code to work accordingly.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To support sriov on a E-Switch manager, num_vfs are queried
to the firmware whenever E-Switch manager is notified by
esw_functions_changed event.
Replace host_params event with esw_functions_changed event that reflects
more appropriate naming.
While at it, also correct num_vfs type from int to u16 as expected by
the function mlx5_esw_query_functions().
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Handle event of power state change in the PCIE slot. When the event
occurs, check if query power state and PCI power fields is supported. If
so, read these fields from MPEIN (management PCIE info) register and
issue a corresponding message.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.
With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.
When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.
The encoding before this patch was as follows:
function_id == 0: pages are requested for the function receiving
the EQE.
function_id != 0: pages are requested for VF identified by the
function_id value
A new one bit field in the EQE identifies that pages are requested for
the ECPF.
The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:
1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function
This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Add support for the HW feature of multi-packet WQE in XDP
xmit flow.
The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.
This reduces both the PCI overhead and the CPU cycles wasted on
writing them.
In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.
Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
Before: 70 Mpps
After: 100 Mpps (+42.8%)
* Dual-port HCA:
Before: 51.7 Mpps
After: 57.3 Mpps (+10.8%)
* In both cases we tested traffic on one port and for now On Dual-port HCAs
we see only small gain, we are working to overcome this bottleneck, but
for the moment only with experimental firmware on dual port HCAs we can
reach the wanted numbers as seen on Single-port HCAs.
XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
Below is the transmit rate of (B), not the redirect rate of (A)
which is in some cases higher.
* (B) is single-port:
Before: 77 Mpps
After: 90 Mpps (+16.8%)
* (B) is dual-port:
Before: 61 Mpps
After: 72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce and use a helper that extracts the opcode
from a CQE (completion queue entry) structure.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use atomic_notifier_chain to fire firmware events at internal mlx5 core
components such as eswitch/fpga/clock/FW tracer/etc.., this is to
avoid explicit calls from low level mlx5_core to upper components and to
simplify the mlx5_core API for future developments.
Simply provide register/unregister notifiers API and call the notifier
chain on firmware async events.
Example: to subscribe to a FW event:
struct mlx5_nb port_event;
MLX5_NB_INIT(&port_event, port_event_handler, PORT_CHANGE);
mlx5_eq_notifier_register(mdev, &port_event);
where:
- port_event_handler is the notifier block callback.
- PORT_EVENT is the suffix of MLX5_EVENT_TYPE_PORT_CHANGE.
The above will guarantee that port_event_handler will receive all FW
events of the type MLX5_EVENT_TYPE_PORT_CHANGE.
To receive all FW/HW events one can subscribe to
MLX5_EVENT_TYPE_NOTIFY_ANY.
The next few patches will start moving all mlx5 core components to use
this new API and cleanup mlx5_eq_async_int misx handler from component
explicit calls and specific logic.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 updates for both net-next and rdma-next
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux: (21 commits)
net/mlx5: Expose DC scatter to CQE capability bit
net/mlx5: Update mlx5_ifc with DEVX UID bits
net/mlx5: Set uid as part of DCT commands
net/mlx5: Set uid as part of SRQ commands
net/mlx5: Set uid as part of SQ commands
net/mlx5: Set uid as part of RQ commands
net/mlx5: Set uid as part of QP commands
net/mlx5: Set uid as part of CQ commands
net/mlx5: Rename incorrect naming in IFC file
net/mlx5: Export packet reformat alloc/dealloc functions
net/mlx5: Pass a namespace for packet reformat ID allocation
net/mlx5: Expose new packet reformat capabilities
{net, RDMA}/mlx5: Rename encap to reformat packet
net/mlx5: Move header encap type to IFC header file
net/mlx5: Break encap/decap into two separated flow table creation flags
net/mlx5: Add support for more namespaces when allocating modify header
net/mlx5: Export modify header alloc/dealloc functions
net/mlx5: Add proper NIC TX steering flow tables support
net/mlx5: Cleanup flow namespace getter switch logic
net/mlx5: Add memic command opcode to command checker
...
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extend the ability to add steering rules to NIC TX flow tables.
For now, we are only adding TX bypass (egress) which is used by the RDMA
side. This will allow to shape outgoing traffic and tweak it if needed, for
example performing encapsulation or rewriting headers.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Modify and query vport state commands share the same admin_state and
op_mod values, rename the enums to fit them both.
In addition, remove the esw prefix from the admin state enum as this
also applied for vnic.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available
An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.
The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.
The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.
Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch updates the mlx5_ifc structures and
command interface to support DEVX.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Saeed Mahameed
Eran Ben Elisha
Yishai Hadas
Feras Daoud
Vu Pham
Yevgeny Kliteynik
Maor Gottlieb
Aya Levin
Bodong Wang
Moni Shoua
Tariq Toukan
Eyal Davidovich
Mark Bloch