This policy flag controls syncing of learned FDB entries to bridge's FDB. If
on, FDB entries learned on bridge port device will be synced. If off, device
may still learn new FDB entries but they will not be synced with bridge's FDB.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows
the AP devices to keep track of the hardware-address-to-IP-address
mapping of the mobile devices within the WLAN network.
The AP will learn this mapping via observing DHCP, ARP, and NS/NA
frames. When a request for such information is made (i.e. ARP request,
Neighbor Solicitation), the AP will respond on behalf of the
associated mobile device. In the process of doing so, the AP will drop
the multicast request frame that was intended to go out to the wireless
medium.
It was recommended at the LKS workshop to do this implementation in
the bridge layer. vxlan.c is already doing something very similar.
The DHCP snooping code will be added to the userspace application
(hostapd) per the recommendation.
This RFC commit is only for IPv4. A similar approach in the bridge
layer will be taken for IPv6 as well.
Signed-off-by: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.
Configuration is done through the netlink interface using e.g.:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link add link eth0 name macvlan1 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44
This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.
Based on work of Stefan Gula <steweg@gmail.com>
v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
add MACADDR_SET command, enable to configure mac for source mode
while creating interface
v10:
- reduce indention level
- rename source_list to source_entry
- use aligned 64bit ether address
- use hash_64 instead of addr[5]
v11:
- rebase for 3.14 / linux-next 20.04.2014
v12
- rebase for linux-next 2014-09-25
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get bridge master info in IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a possibility for userspace to set various (so far
two) modes of generating addresses. This is useful for example for
NetworkManager because it can set the mode to NONE and take care of link
local addresses itself. That allow it to have the interface up,
monitoring carrier but still don't have any addresses on it.
One more use-case by Dan Williams:
<quote>
WWAN devices often have their LL address provided by the firmware of the
device, which sometimes refuses to respond to incorrect LL addresses
when doing DHCPv6 or IPv6 ND. The kernel cannot generate the correct LL
address for two reasons:
1) WWAN pseudo-ethernet interfaces often construct a fake MAC address,
or read a meaningless MAC address from the firmware. Thus the EUI64 and
the IPv6LL address the kernel assigns will be wrong. The real LL
address is often retrieved from the firmware with AT or proprietary
commands.
2) WWAN PPP interfaces receive their LL address from IPV6CP, not from
kernel assignments. Only after IPV6CP has completed do we know the LL
address of the PPP interface and its peer. But the kernel has already
assigned an incorrect LL address to the interface.
So being able to suppress the kernel LL address generation and assign
the one retrieved from the firmware is less complicated and more robust.
</quote>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.
Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to monitor carrier on/off transitions and detect link
flapping issues:
- new /sys/class/net/X/carrier_changes
- new rtnetlink IFLA_CARRIER_CHANGES (getlink)
Tested:
- grep . /sys/class/net/*/carrier_changes
+ ip link set dev X down/up
+ plug/unplug cable
- updated iproute2: prints IFLA_CARRIER_CHANGES
- iproute2 20121211-2 (debian): unchanged behavior
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in net-next only, for couple of days. Not used anymore, and never
should have been. So just remove it and pretend it was never there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88ae0)
Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.
This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is IFF_SLAVE, extend link dev netlink attributes to include
slave attributes with new IFLA_SLAVE nest. Add netlink notification
(RTM_NEWLINK) when slave status changes from backup to active, or
visa-versa.
Adds new ndo_get_slave op to net_device_ops to fill skb with IFLA_SLAVE
attributes. Currently only used by bonding driver, but could be
used by other aggregating devices with slaves.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_AD_SELECT to allow get/set of bonding parameter
ad_select via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_AD_LACP_RATE to allow get/set of bonding parameter
lacp_rate via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_PACKETS_PER_SLAVE to allow get/set of bonding parameter
packets_per_slave via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_ALL_SLAVES_ACTIVE to allow get/set of bonding parameter
all_slaves_active via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_NUM_PEER_NOTIF to allow get/set of bonding parameter
num_grat_arp via netlink. Bonding parameter num_unsol_na is
synonymous with num_grat_arp, so add only one netlink attribute
to represent both bonding parameters.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_RESEND_IGMP to allow get/set of bonding parameter
resend_igmp via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BOND_XMIT_HASH_POLICY to allow get/set of bonding parameter
xmit_hash_policy via netlink.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman
Jiri Pirko
Mahesh Bandewar
Kyeyoon Park
Michael Braun
Tom Herbert
Sucheta Chakraborty
david decotigny
sfeldma@cumulusnetworks.com