* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
netfilter: Remove ADVANCED dependency from NF_CONNTRACK_NETBIOS_NS
ipv4: flush route cache after change accept_local
sch_red: fix red_change
Revert "udp: remove redundant variable"
bridge: master device stuck in no-carrier state forever when in user-stp mode
ipv4: Perform peer validation on cached route lookup.
net/core: fix rollback handler in register_netdevice_notifier
sch_red: fix red_calc_qavg_from_idle_time
bonding: only use primary address for ARP
ipv4: fix lockdep splat in rt_cache_seq_show
sch_teql: fix lockdep splat
net: fec: Select the FEC driver by default for i.MX SoCs
isdn: avoid copying too long drvid
isdn: make sure strings are null terminated
netlabel: Fix build problems when IPv6 is not enabled
sctp: better integer overflow check in sctp_auth_create_key()
sctp: integer overflow in sctp_auth_create_key()
ipv6: Set mcast_hops to IPV6_DEFAULT_MCASTHOPS when -1 was given.
net: Fix corruption in /proc/*/net/dev_mcast
mac80211: fix race between the AGG SM and the Tx data path
...
Currently netem is not in the ability to emulate channel bandwidth. Only static
delay (and optional random jitter) can be configured.
To emulate the channel rate the token bucket filter (sch_tbf) can be used. But
TBF has some major emulation flaws. The buffer (token bucket depth/rate) cannot
be 0. Also the idea behind TBF is that the credit (token in buckets) fills if
no packet is transmitted. So that there is always a "positive" credit for new
packets. In real life this behavior contradicts the law of nature where
nothing can travel faster as speed of light. E.g.: on an emulated 1000 byte/s
link a small IPv4/TCP SYN packet with ~50 byte require ~0.05 seconds - not 0
seconds.
Netem is an excellent place to implement a rate limiting feature: static
delay is already implemented, tfifo already has time information and the
user can skip TBF configuration completely.
This patch implement rate feature which can be configured via tc. e.g:
tc qdisc add dev eth0 root netem rate 10kbit
To emulate a link of 5000byte/s and add an additional static delay of 10ms:
tc qdisc add dev eth0 root netem delay 10ms rate 5KBps
Note: similar to TBF the rate extension is bounded to the kernel timing
system. Depending on the architecture timer granularity, higher rates (e.g.
10mbit/s and higher) tend to transmission bursts. Also note: further queues
living in network adaptors; see ethtool(8).
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
netdev->neigh_priv_len records the private area length.
This will trigger for neigh_table objects which set tbl->entry_size
to zero, and the first instances of this will be forthcoming.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Update comments describing device power management callbacks
PM / Sleep: Update documentation related to system wakeup
PM / Runtime: Make documentation follow the new behavior of irq_safe
PM / Sleep: Correct inaccurate information in devices.txt
PM / Domains: Document how PM domains are used by the PM core
PM / Hibernate: Do not leak memory in error/test code paths
Networking stack support for byte queue limits, uses dynamic queue
limits library. Byte queue limits are maintained per transmit queue,
and a dql structure has been added to netdev_queue structure for this
purpose.
Configuration of bql is in the tx-<n> sysfs directory for the queue
under the byte_queue_limits directory. Configuration includes:
limit_min, bql minimum limit
limit_max, bql maximum limit
hold_time, bql slack hold time
Also under the directory are:
limit, current byte limit
inflight, current number of bytes on the queue
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add interfaces for drivers to call for recording number of packets and
bytes at send time and transmit completion. Also, added a function to
"reset" a queue. These will be used by Byte Queue Limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create separate queue state flags so that either the stack or drivers
can turn on XOFF. Added a set of functions used in the stack to determine
if a queue is really stopped (either by stack or driver)
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of dynamic queue limits (dql). This is a libary which
allows a queue limit to be dynamically managed. The goal of dql is
to set the queue limit, number of objects to the queue, to be minimized
without allowing the queue to be starved.
dql would be used with a queue which has these properties:
1) Objects are queued up to some limit which can be expressed as a
count of objects.
2) Periodically a completion process executes which retires consumed
objects.
3) Starvation occurs when limit has been reached, all queued data has
actually been consumed but completion processing has not yet run,
so queuing new data is blocked.
4) Minimizing the amount of queued data is desirable.
A canonical example of such a queue would be a NIC HW transmit queue.
The queue limit is dynamic, it will increase or decrease over time
depending on the workload. The queue limit is recalculated each time
completion processing is done. Increases occur when the queue is
starved and can exponentially increase over successive intervals.
Decreases occur when more data is being maintained in the queue than
needed to prevent starvation. The number of extra objects, or "slack",
is measured over successive intervals, and to avoid hysteresis the
limit is only reduced by the miminum slack seen over a configurable
time period.
dql API provides routines to manage the queue:
- dql_init is called to intialize the dql structure
- dql_reset is called to reset dynamic values
- dql_queued called when objects are being enqueued
- dql_avail returns availability in the queue
- dql_completed is called when objects have be consumed in the queue
Configuration consists of:
- max_limit, maximum limit
- min_limit, minimum limit
- slack_hold_time, time to measure instances of slack before reducing
queue limit
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just hit this during my testing. Isn't there another bug lurking?
BUG kmalloc-8: Redzone overwritten
INFO: 0xc0000000de9dec48-0xc0000000de9dec4b. First byte 0x0 instead of 0xcc
INFO: Allocated in .__seq_open_private+0x30/0xa0 age=0 cpu=5 pid=3896
.__kmalloc+0x1e0/0x2d0
.__seq_open_private+0x30/0xa0
.seq_open_net+0x60/0xe0
.dev_mc_seq_open+0x4c/0x70
.proc_reg_open+0xd8/0x260
.__dentry_open.clone.11+0x2b8/0x400
.do_last+0xf4/0x950
.path_openat+0xf8/0x480
.do_filp_open+0x48/0xc0
.do_sys_open+0x140/0x250
syscall_exit+0x0/0x40
dev_mc_seq_ops uses dev_seq_start/next/stop but only allocates
sizeof(struct seq_net_private) of private data, whereas it expects
sizeof(struct dev_iter_state):
struct dev_iter_state {
struct seq_net_private p;
unsigned int pos; /* bucket << BUCKET_SPACE + offset */
};
Create dev_seq_open_ops and use it so we don't have to expose
struct dev_iter_state.
[ Problem added by commit f04565ddf5 (dev: use name hash for
dev_seq_ops) -Eric ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments describing device power management callbacks in
include/pm.h are outdated and somewhat confusing, so make them
reflect the reality more accurately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Fix extra wakeups from __remove_hrtimer()
timekeeping: add arch_offset hook to ktime_get functions
clocksource: Avoid selecting mult values that might overflow when adjusted
time: Improve documentation of timekeeeping_adjust()
Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Towards adding RSS support for IB drivers/application who use
the mlx4 HW, make the RSS related definitions global and change
the mlx4_en driver to use them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices need to know if the data is to be output or read, so add a
data direction into the eeprom structure to tell the driver whether the
data line should be driven.
The user in this case is the Micrel KS8851 which has a direction
control for the EEPROM data line and thus needs to know whether
to drive it (writing) or to tristate it for receiving.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the kconfig types to tristate and adjust the condition for
declaring net_device::dsa_ptr to allow for this.
Adjust the makefile so that if NET_DSA_MV88E6123_61_65=y and
NET_DSA_MV88E6131=m or vice versa then both drivers are built-in. We
could leave these options as bool and make NET_DSA_MV88E6XXX a
user-selected option, but that would break existing configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
