We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for control peripheral of EUD (Embedded USB Debugger) to
listen to events such as USB attach/detach, pet EUD to indicate software
is functional.Reusing the platform device kobj, sysfs entry 'enable' is
created to enable or disable EUD.
To enable the eud the following needs to be done
echo 1 > /sys/bus/platform/.../enable
To disable eud, following is the command
echo 0 > /sys/bus/platform/.../enable
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Link: https://lore.kernel.org/r/0ac5c2b2c8e4ce4f4f342a08b48cfc61aeaf7ee8.1644339918.git.quic_schowdhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2.0 spec chapter 11.24.2.13 says that the USB port which is going
under test needs to be put in suspend state before sending the test
command. Many hubs, don't enforce this precondition and they work fine
without this step. We should follow the specification and put the USB
port in suspend before sending the test command.
Also there are some "special" hubs, which requires to disable the USB
port power instead of putting it in suspend. I found out only three hubs
which requires this step, but if more are found, they can be added to
the list.
Since this changes the default implementation, it raises the posibility
of finding other broken hubs which are not compliant with the spec and
the test command might not work is the port is suspended. If such hubs
are found, a similar workaround like the disable part can be implemented
to skip putting the port in suspend.
Signed-off-by: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20211213183617.14156-2-heghedus.razvan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ce3e90d5a0.
The commit in question added list of quirky hubs, but the match
implementation clearly hasn't been tested at all.
First, hub_udev->dev.parent does not represent a USB interface so using
to_usb_interface() makes no sense and we'd be passing a random pointer
to usb_match_id().
Second, if hub_udev is a root hub it doesn't even even represent a USB
device.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: ce3e90d5a0 ("usb: misc: ehset: Workaround for "special" hubs")
Cc: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20211007090601.19156-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2.0 spec chapter 11.24.2.13 says that the USB port which is going
under test needs to be put in suspend state before sending the test
command. Many hubs, don't enforce this precondition and they work fine
without this step. But there are some "special" hubs, which requires to
disable the port power before sending the test command.
Because the USB spec mention that the port should be suspended, also
do this step before sending the test command. This could rise the
problem with other hubs which are not compliant with the spec and the
test command will not work if the port is suspend. If such hubs are
found, a similar workaround like the disable part could be implemented
to skip the suspend port command.
Signed-off-by: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20210915121615.3790-1-heghedus.razvan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/806d0b1a-365b-93d9-3fc1-922105ca5e61@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the set-speed request which erroneously used USB_DIR_IN and update
the default timeout argument to match (same value).
Fixes: 5638e4d92e ("USB: add PlayStation 2 Trance Vibrator driver")
Cc: stable@vger.kernel.org # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133109.17396-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
