Pull HID fixes from Jiri Kosina:
- two cosmetic fixes from Daniel Axtens and Hans de Goede
- fix for I2C command mismatch fix for cp2112 driver from Eudean Sun
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: lower log level for unknown main item tags to warnings
HID: holtekff: move MODULE_* parameters out of #ifdef block
HID: cp2112: Fix I2C_BLOCK_DATA transactions
Given all the effort distros have done with splash-screens to give
users a nice clean boot experience, we really want dmesg --level=err
to not print anything unless there is a real problem with either the
hardware or the kernel. Buggy HID descriptors unfortunately happen
all too often, so lower the log level to warning keep the console
clear of error messages such as:
[ 441.079664] apple 0005:05AC:0239.0003: unknown main item tag 0x0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If you compile with:
CONFIG_HID_HOLTEK=m
CONFIG_HOLTEK_FF is not set
You get the following warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/hid/hid-holtekff.o
see include/linux/module.h for more information
Fix this by moving the module info out of the #ifdef CONFIG_HOLTEK_FF
block and into the un-guarded part of the file.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing driver erroneously treats I2C_BLOCK_DATA and BLOCK_DATA
commands the same.
For I2C_BLOCK_DATA reads, the length of the read is provided in
data->block[0], but the length itself should not be sent to the slave. In
contrast, for BLOCK_DATA reads no length is specified since the length
will be the first byte returned from the slave. When copying data back
to the data buffer, for an I2C_BLOCK_DATA read we have to take care not to
overwrite data->block[0] to avoid overwriting the length. A BLOCK_DATA
read doesn't have this concern since the first byte returned by the device
is the length and belongs in data->block[0].
For I2C_BLOCK_DATA writes, the length is also provided in data->block[0],
but the length itself is not sent to the slave (in contrast to BLOCK_DATA
writes where the length prefixes the data sent to the slave).
This was tested on physical hardware using i2cdump with the i and s flags
to test the behavior of I2C_BLOCK_DATA reads and BLOCK_DATA reads,
respectively. Writes were not tested but the I2C_BLOCK_DATA write change
is pretty simple to verify by inspection.
Signed-off-by: Eudean Sun <eudean@arista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull HID updates from Jiri Kosina:
- high resolution mode for Dell canvas support, from Benjamin Tissoires
- pen handling fixes for the Wacom driver, from Jason Gerecke
- i2c-hid: Apollo-Lake based laptops improvements, from Hans de Goede
- Input/Core: eraser tool support, from Ping Cheng
- new ALPS touchpad (T4, found currently on HP EliteBook 1000, Zbook
Stduio and HP Elite book x360) supportm from Masaki Ota
- other smaller assorted fixes
* 'for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (33 commits)
HID: cp2112: fix broken gpio_direction_input callback
HID: cp2112: fix interface specification URL
HID: Wacom: switch Dell canvas into highres mode
HID: wacom: generic: Send BTN_STYLUS3 when both barrel switches are set
HID: sony: Fix SHANWAN pad rumbling on USB
HID: i2c-hid: Add no-irq-after-reset quirk for 0911:5288 device
HID: add backlight level quirk for Asus ROG laptops
HID: cp2112: add HIDRAW dependency
HID: Add ID 044f:b605 ThrustMaster, Inc. force feedback Racing Wheel
HID: hid-logitech: remove redundant assignment to pointer value
HID: wacom: generic: Recognize WACOM_HID_WD_PEN as a type of pen collection
HID: rmi: Check that a device is a RMI device before calling RMI functions
HID: add multi-input quirk for GamepadBlock
HID: alps: add new U1 device ID
HID: alps: add support for Alps T4 Touchpad device
HID: alps: remove variables local to u1_init() from the device struct
HID: alps: properly handle max_fingers and minimum on X and Y axis
HID: alps: Separate U1 device code
HID: alps: delete unnecessary struct u1_dev devInfo
HID: usbhid: Convert timers to use timer_setup()
...
- High resolution mode for DEll canvas support, from Benjamin Tissoires
- A lot of improvements to pen handling in the Wacom driver, from Jason Gerecke
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- cp2112: GPIO error handling and Kconfig fixes from Sébastien Szymanski
- i2c-hid: fixup / quirk for Apollo-Lake based laptops, from Hans de Goede
- Input/Core: add eraser tool support, from Ping Cheng
- small assorted code fixes
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dell Canvas exports 2 collections for the Pen part. The only
difference between the 2 is that the default one has half the resolution
of the second one.
The Windows driver switches the tablet into the second mode, so we should
behave the same.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.
Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SHANWAN PS3 clone joypad will start its rumble motors as soon as
it is plugged in via USB. As the additional USB interrupt does nothing on
the original PS3 Sixaxis joypads, and makes a number of other
clone joypads actually start sending data, disable that call for
the SHANWAN so the rumble motors aren't started on plug.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Several cheap Apollo Lake based laptops / 2-in-1s use an i2c-hid mt
touchpad which is advertised by the DSDT with an ACPI HID of "SYNA3602",
this touchpad can be found on e.g. the Cube Thinker and the EZBook 3 Pro.
On my "T-bao Tbook air" the i2c-hid driver fails to bind to this touchpad:
"i2c_hid i2c-SYNA3602:00: failed to reset device.".
After some debuging this it seems that this touchpad simply never sends
an interrupt after a reset as expected by the i2c hid driver. This commit
adds a quirk for this device, making i2c_hid_command sleep 100ms after
a reset instead of waiting for an irq, fixing i2c-hid failing to bind to
this touchpad.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On laptops such as Asus GL553VD, setting keyboard backlight levels
does not work. This change enables F3/F4 keys to set backlight levels
(from 0 to 3, total 4 levels) on such laptops.
It is intended only to the following device: 0x0b05 1854:
P: Vendor=0b05 ProdID=1854 Rev=03.02
S: Manufacturer=ITE Tech. Inc.
S: Product=ITE Device(8910)
[jkosina@suse.cz: massage changelog a little bit]
Signed-off-by: Mustafa C Kuscu <mustafakuscu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
