Pull ktest updates from Steven Rostedt:
- Have config-bisect save the good/bad configs at each step.
- Show log file location even on success
- Add PRE_TEST_DIE to kill test if the PRE_TEST fails
- Add a NOT operator for conditionals in config file
- Add the log output of the last test when emailing on failure.
- Other minor clean ups and small fixes.
* tag 'ktest-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest.pl: Fix spelling mistake "Cant" -> "Can't"
ktest.pl: Change the logic to control the size of the log file emailed
ktest.pl: Add MAIL_MAX_SIZE to limit the amount of log emailed
ktest.pl: Add the log of last test in email on failure
ktest.pl: Turn off buffering to the log file
ktest.pl: Just open up the log file once
ktest.pl: Add a NOT operator
ktest.pl: Define PRE_TEST_DIE to kill the test if the PRE_TEST fails
ktest.pl: Always show log file location if defined even on success
ktest.pl: Have config-bisect save each config used in the bisect
If the log file for a given test is larger than the max size given then use
set the seek from the end of the log file instead of from the start of the
test.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The log file should be up to date to whatever is happening in ktest.
Disable buffering to the LOG output file handle.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Currently, every write to the log file is done by opening the file, writing
to it, then closing the file. This rather expensive. Just open it at the
beginning and close it at the end.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There is a NOT DEFINED operator, but there is not an operator that can
negate any other expression.
For example: NOT (${FOO} == boot || ${BAR} == run)
Add the keyword NOT to allow the ktest.pl config files to negate operators.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Currently, if a PRE_TEST is defined and ran, but fails, there's nothing
currently available to make the test fail too. Add a PRE_TEST_DIE option that
when set, if a PRE_TEST is defined and fails, the test will die too.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If a log file is defined and the test were to error, a print statement is
made that shows the user where the log file is to examine it further. But
this is not done if the test were to succeed.
I find it annoying that it does not show where the log file is on success,
as I run several different tests that place their log files in various
locations, and even though the test pass, there's things I want to look at
in the log file (like warnings). It is much easier to find where the log
file is, if it is displayed at the end of a test.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When performing a automatic config bisect via ktest.pl, it is very useful to
have a copy of each of the bisects used. This way, if a bisect were to go
wrong, it is possible to retrace the steps and continue at the location
before the error was made.
The ktest.pl will make a copy of the good and bad configs, labeled as such,
as well as a number attached to it that represents the iteration of the
bisect. These files are saved in the ktest temp directory where it currently
stores the good and bad config files.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Before rebooting the box, a "ssh sync" is called to the test machine to see
if it is alive or not. But if the test machine is in a partial state, that
ssh may never actually finish, and the ktest test hangs.
Add a 10 second timeout to the sync test, which will fail after 10 seconds
and then cause the test to reboot the test machine.
Cc: stable@vger.kernel.org
Fixes: 6474ace999 ("ktest.pl: Powercycle the box on reboot if no connection can be made")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
For the last time, I screwed up my ktest config file, and the build went
into the default "randconfig", blowing away the .config that I had set up.
The reason for the default randconfig was because when this was first
written, I wanted to do a bunch of randconfigs. But as time progressed,
ktest isn't about randconfig anymore, and because randconfig destroys the
config in the build directory, it's a dangerous default to have. Use
oldconfig as the default.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
For BLS, kernel entry is added by kernel-install command through
POST_INSALL, for example,
POST_INSTALL = ssh root@Test "/usr/bin/kernel-install \
add $KERNEL_VERSION /boot/vmlinuz-$KERNEL_VERSION"
The entry is removed by kernel-install command and the kernel
version is needed for the argument.
Pass KERNEL_VERSION variable to POST_KTEST so that kernel-install
command can remove the entry like as follows:
POST_KTEST = ssh root@Test "/usr/bin/kernel-install remove $KERNEL_VERSION"
Link: http://lkml.kernel.org/r/20190509213647.6276-5-msys.mizuma@gmail.com
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Unexpected power cycle occurs while the installation of the
kernel.
ssh root@Test sync ... [0 seconds] SUCCESS
ssh root@Test reboot ... [1 second] FAILED!
virsh destroy Test; sleep 5; virsh start Test ... [6 seconds] SUCCESS
That is because REBOOT, the default is "ssh $SSH_USER@$MACHINE
reboot", exits as 255 even if the reboot is successfully done,
like as:
]# ssh root@Test reboot
Connection to Test closed by remote host.
]# echo $?
255
]#
To avoid the unexpected power cycle, introduce a new parameter,
REBOOT_RETURN_CODE to judge whether REBOOT is successfully done
or not.
Link: http://lkml.kernel.org/r/20190418135943.12640-1-msys.mizuma@gmail.com
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
