Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull tty/serial driver updates from Greg KH:
"Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should
be helpful for many.
The last patch in the series is a revert of an older one in the tree,
it came late but it resolves a reported issue that linux-next was
having for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues"
* tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (85 commits)
Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
serial: sccnxp: Allow to use non-standard baud rates
serial: sccnxp: Adds a delay between sequential read/write cycles
tty: serial: qcom_geni_serial: Fix UART hang
tty: serial: qcom_geni_serial: Fix wrap around of TX buffer
serial: max310x: Fix tx_empty() callback
dt-bindings: serial: sh-sci: Document r8a774c0 bindings
dt-bindings: serial: sh-sci: Document r8a774a1 bindings
Fonts: New Terminus large console font
dt-bindings: serial: lpuart: add imx8qxp compatible string
serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
serial: uartps: Fix error path when alloc failed
serial: uartps: Check if the device is a console
serial: uartps: Add the device_init_wakeup
tty: serial: samsung: Increase maximum baudrate
tty: serial: samsung: Properly set flags in autoCTS mode
tty: Use of_node_name_{eq,prefix} for node name comparisons
tty/serial: do not free trasnmit buffer page under port lock
serial: 8250: Rate limit serial port rx interrupts during input overruns
dt-bindings: serial: 8250: Add rate limit for serial port input overruns
...
Pull audit updates from Paul Moore:
"In the finest of holiday of traditions, I have a number of gifts to
share today. While most of them are re-gifts from others, unlike the
typical re-gift, these are things you will want in and around your
tree; I promise.
This pull request is perhaps a bit larger than our typical PR, but
most of it comes from Jan's rework of audit's fanotify code; a very
welcome improvement. We ran this through our normal regression tests,
as well as some newly created stress tests and everything looks good.
Richard added a few patches, mostly cleaning up a few things and and
shortening some of the audit records that we send to userspace; a
change the userspace folks are quite happy about.
Finally YueHaibing and I kick in a few patches to simplify things a
bit and make the code less prone to errors.
Lastly, I want to say thanks one more time to everyone who has
contributed patches, testing, and code reviews for the audit subsystem
over the past year. The project is what it is due to your help and
contributions - thank you"
* tag 'audit-pr-20181224' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (22 commits)
audit: remove duplicated include from audit.c
audit: shorten PATH cap values when zero
audit: use current whenever possible
audit: minimize our use of audit_log_format()
audit: remove WATCH and TREE config options
audit: use session_info helper
audit: localize audit_log_session_info prototype
audit: Use 'mark' name for fsnotify_mark variables
audit: Replace chunk attached to mark instead of replacing mark
audit: Simplify locking around untag_chunk()
audit: Drop all unused chunk nodes during deletion
audit: Guarantee forward progress of chunk untagging
audit: Allocate fsnotify mark independently of chunk
audit: Provide helper for dropping mark's chunk reference
audit: Remove pointless check in insert_hash()
audit: Factor out chunk replacement code
audit: Make hash table insertion safe against concurrent lookups
audit: Embed key into chunk
audit: Fix possible tagging failures
audit: Fix possible spurious -ENOSPC error
...
This reverts commit 6d11023c34.
It causes issues with Guenter's test systems and since there seems to
not be any agreement about _why_ this is a problem, but reverting it
fixes things, let's revert until the root cause is found.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc fixes from David Miller:
"Just some small fixes here and there, and a refcount leak in a serial
driver, nothing serious"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunsu: fix refcount leak
sparc: Set "ARCH: sunxx" information on the same line
sparc: vdso: Drop implicit common-page-size linker flag
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the use of non-standard baud rates.
For these purposes, we use the built-in timer/counter.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a delay between sequential read/write cycles,
to ensure the required minimum inactive time (tRWD). A time value
from the datasheet has been added for each type of supported chips.
The “inline” compiler attribute has been removed from the
read/write functions, simply allow the compiler to control this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a serial console write occured while a UART transmit command was
waiting for a done signal then no further data would be sent until
something new kicked the system into gear. If there is already data
waiting in the circular buffer we must re-enable the tx watermark so we
receive the expected interrupts.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit a1fee899e5 ("tty: serial: qcom_geni_serial: Fix
softlock") the size of TX transfers was limited to the TX FIFO size,
and wrap arounds of the UART circular buffer were split into two
transfers. With the commit wrap around are allowed within a transfer.
The TX FIFO of the geni serial port uses a word size of 4 bytes. In
case of a circular buffer wrap within a transfer the driver currently
may write an incomplete word to the FIFO, with some bytes containing
data from the circular buffer and others being zero. Since the
transfer isn't completed yet the zero bytes are sent as if they were
actual data.
Handle wrap arounds of the TX buffer properly and ensure that words
written to the TX FIFO always contain valid data (unless the transfer
is completed).
Fixes: a1fee899e5 ("tty: serial: qcom_geni_serial: Fix softlock")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Tested-by: Ryan Case <ryandcase@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cdns_uart_console allocation failed there is a need to also clear
ID from ID list.
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialise the device wakeup.
The device_init_wakeup is needed for the wakeup to work by default.
Uart can be configured as the primary wakeup source so it is good to
enable wakeup by default.
The same functionality is enabled also by 8250_omap, atmel_serial,
omap-serial and stm32-usart.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver can be used to communicate with Bluetooth chip in high-speed
UART mode, so increase the maximum baudrate to 3Mbps.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
[mszyprow: rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 391f93f2ec ("serial: core: Rework hw-assited flow control support")
has changed the way the autoCTS mode is handled.
According to that change, serial drivers which enable H/W autoCTS mode must
set UPSTAT_AUTOCTS to prevent the serial core from inadvertently disabling
TX. This patch adds proper handling of UPSTAT_AUTOCTS flag.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
[mszyprow: rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LKP has hit yet another circular locking dependency between uart
console drivers and debugobjects [1]:
CPU0 CPU1
rhltable_init()
__init_work()
debug_object_init
uart_shutdown() /* db->lock */
/* uart_port->lock */ debug_print_object()
free_page() printk()
call_console_drivers()
debug_check_no_obj_freed() /* uart_port->lock */
/* db->lock */
debug_print_object()
So there are two dependency chains:
uart_port->lock -> db->lock
And
db->lock -> uart_port->lock
This particular circular locking dependency can be addressed in several
ways:
a) One way would be to move debug_print_object() out of db->lock scope
and, thus, break the db->lock -> uart_port->lock chain.
b) Another one would be to free() transmit buffer page out of db->lock
in UART code; which is what this patch does.
It makes sense to apply a) and b) independently: there are too many things
going on behind free(), none of which depend on uart_port->lock.
The patch fixes transmit buffer page free() in uart_shutdown() and,
additionally, in uart_port_startup() (as was suggested by Dmitry Safonov).
[1] https://lore.kernel.org/lkml/20181211091154.GL23332@shao2-debian/T/#u
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Waiman Long <longman@redhat.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.
The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable M_TX_FIFO_WATERMARK_EN after we've sent all data for a given
transaction so we don't continue to receive a flurry of free space
interrupts while waiting for the M_CMD_DONE notification. Re-enable the
watermark when establishing the next transaction.
Also clear the watermark interrupt after filling the FIFO so we do not
receive notification again prior to actually having free space.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On (H)SCIF, sci_submit_rx() is called in the receive interrupt handler.
Hence if DMA submission fails, the interrupt handler should resume
handling reception using PIO, else no more data is received.
Make sci_submit_rx() return an error indicator, so the receive interrupt
handler can act appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds
Manivannan Sadhasivam
Greg Kroah-Hartman
Yangtao Li
Alexander Shiyan
Ryan Case
Matthias Kaehlcke
Nava kishore Manne
Michal Simek
Shubhrajyoti Datta
Paul Burton
Seung-Woo Kim
Beomho Seo
Rob Herring
Sergey Senozhatsky
Darwin Dingel
Geert Uytterhoeven