Currently logging of a successful profile load only logs the basename
of the profile. This can result in confusion when a child profile has
the same name as the another profile in the set. Logging the hname
will ensure there is no confusion.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
currently only the profile that is causing the failure is logged. This
makes it more confusing than necessary about which profiles loaded
and which didn't. So make sure to log success and failure messages for
all profiles in the set being loaded.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
The current behavior is confusing as it causes exec failures to report
the executable is missing instead of identifying that apparmor
caused the failure.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
When set atomic replacement is used and the parent is updated before the
child, and the child did not exist in the old parent so there is no
direct replacement then the new child is incorrectly added to the old
parent. This results in the new parent not having the child(ren) that
it should and the old parent when being destroyed asserting the
following error.
AppArmor: policy_destroy: internal error, policy '<profile/name>' still
contains profiles
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
Extend the PCR supplied as a parameter, instead of assuming that the
measurement entry uses the default configured PCR.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
IMA avoids re-measuring files by storing the current state as a flag in
the integrity cache. It will then skip adding a new measurement log entry
if the cache reports the file as already measured.
If a policy measures an already measured file to a new PCR, the measurement
will not be added to the list. This patch implements a new bitfield for
specifying which PCR the file was measured into, rather than if it was
measured.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Template entry duplicates are prevented from being added to the
measurement list by checking a hash table that contains the template
entry digests. However, the PCR value is not included in this comparison,
so duplicate template entry digests with differing PCRs may be dropped.
This patch redefines duplicate template entries as template entries with
the same digest and same PCR values.
Reported-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
IMA assumes that the same default Kconfig PCR is extended for each
entry. This patch replaces the default configured PCR with the policy
defined PCR.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
The IMA measurement list entries include the Kconfig defined PCR value.
This patch defines a new ima_template_entry field for including the PCR
as specified in the policy rule.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Different policy rules may extend different PCRs. This patch retrieves
the specific PCR for the matched rule. Subsequent patches will include
the rule specific PCR in the measurement list and extend the appropriate
PCR.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
This patch defines a new IMA measurement policy rule option "pcr=",
which allows extending different PCRs on a per rule basis. For example,
the system independent files could extend the default IMA Kconfig
specified PCR, while the system dependent files could extend a different
PCR.
The following is an example of this usage with an SELinux policy; the
rule would extend PCR 11 with system configuration files:
measure func=FILE_CHECK mask=MAY_READ obj_type=system_conf_t pcr=11
Changelog v3:
- FIELD_SIZEOF returns bytes, not bits. Fixed INVALID_PCR
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
To keep track of which measurements have been extended to which PCRs, this
patch defines a new integrity_iint_cache field named measured_pcrs. This
field is a bitmask of the PCRs measured. Each bit corresponds to a PCR
index. For example, bit 10 corresponds to PCR 10.
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
This works in exactly the same way as the CIPSO label cache.
The idea is to allow the lsm to cache the result of a secattr
lookup so that it doesn't need to perform the lookup for
every skbuff.
It introduces two sysctl controls:
calipso_cache_enable - enables/disables the cache.
calipso_cache_bucket_size - sets the size of a cache bucket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This makes it possible to route the error to the appropriate
labelling engine. CALIPSO is far less verbose than CIPSO
when encountering a bogus packet, so there is no need for a
CALIPSO error handler.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
In some cases, the lsm needs to add the label to the skbuff directly.
A NF_INET_LOCAL_OUT IPv6 hook is added to selinux to match the IPv4
behaviour. This allows selinux to label the skbuffs that it requires.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
