Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: imx219
- Support for some new pixelformats
- Support for Sun8i SoC
- Added more codecs to meson vdec driver
- Prepare for removing the legacy usbvision driver by moving it to
staging. This driver has issues and use legacy core APIs. If nobody
steps up to address those, it is time for its retirement.
- Several cleanups and improvements on drivers, with the addition of
new supported boards
* tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (236 commits)
media: venus: firmware: Ignore secure call error on first resume
media: mtk-vpu: load vpu firmware from the new location
media: i2c: video-i2c: fix build errors due to 'imply hwmon'
media: MAINTAINERS: add myself to co-maintain Hantro G1/G2 for i.MX8MQ
media: hantro: add initial i.MX8MQ support
media: dt-bindings: Document i.MX8MQ VPU bindings
media: vivid: fix incorrect PA assignment to HDMI outputs
media: hantro: Add linux-rockchip mailing list to MAINTAINERS
media: cedrus: h264: Fix 4K decoding on H6
media: siano: Use scnprintf() for avoiding potential buffer overflow
media: rc: Use scnprintf() for avoiding potential buffer overflow
media: allegro: create new struct for channel parameters
media: allegro: move mail definitions to separate file
media: allegro: pass buffers through firmware
media: allegro: verify source and destination buffer in VCU response
media: allegro: handle dependency of bitrate and bitrate_peak
media: allegro: read bitrate mode directly from control
media: allegro: make QP configurable
media: allegro: make frame rate configurable
media: allegro: skip filler data if possible
...
Pull seccomp updates from Kees Cook:
"A couple of seccomp updates. They're both mostly bug fixes that I
wanted to have sit in linux-next for a while:
- allow TSYNC and USER_NOTIF together (Tycho Andersen)
- add missing compat_ioctl for notify (Sven Schnelle)"
* tag 'seccomp-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
seccomp: Add missing compat_ioctl for notify
seccomp: allow TSYNC and USER_NOTIF together
Pull io_uring updates from Jens Axboe:
"Here are the io_uring changes for this merge window. Light on new
features this time around (just splice + buffer selection), lots of
cleanups, fixes, and improvements to existing support. In particular,
this contains:
- Cleanup fixed file update handling for stack fallback (Hillf)
- Re-work of how pollable async IO is handled, we no longer require
thread offload to handle that. Instead we rely using poll to drive
this, with task_work execution.
- In conjunction with the above, allow expendable buffer selection,
so that poll+recv (for example) no longer has to be a split
operation.
- Make sure we honor RLIMIT_FSIZE for buffered writes
- Add support for splice (Pavel)
- Linked work inheritance fixes and optimizations (Pavel)
- Async work fixes and cleanups (Pavel)
- Improve io-wq locking (Pavel)
- Hashed link write improvements (Pavel)
- SETUP_IOPOLL|SETUP_SQPOLL improvements (Xiaoguang)"
* tag 'for-5.7/io_uring-2020-03-29' of git://git.kernel.dk/linux-block: (54 commits)
io_uring: cleanup io_alloc_async_ctx()
io_uring: fix missing 'return' in comment
io-wq: handle hashed writes in chains
io-uring: drop 'free_pfile' in struct io_file_put
io-uring: drop completion when removing file
io_uring: Fix ->data corruption on re-enqueue
io-wq: close cancel gap for hashed linked work
io_uring: make spdxcheck.py happy
io_uring: honor original task RLIMIT_FSIZE
io-wq: hash dependent work
io-wq: split hashing and enqueueing
io-wq: don't resched if there is no work
io-wq: remove duplicated cancel code
io_uring: fix truncated async read/readv and write/writev retry
io_uring: dual license io_uring.h uapi header
io_uring: io_uring_enter(2) don't poll while SETUP_IOPOLL|SETUP_SQPOLL enabled
io_uring: Fix unused function warnings
io_uring: add end-of-bits marker and build time verify it
io_uring: provide means of removing buffers
io_uring: add IOSQE_BUFFER_SELECT support for IORING_OP_RECVMSG
...
Pull block driver updates from Jens Axboe:
- floppy driver cleanup series from Willy
- NVMe updates and fixes (Various)
- null_blk trace improvements (Chaitanya)
- bcache fixes (Coly)
- md fixes (via Song)
- loop block size change optimizations (Martijn)
- scnprintf() use (Takashi)
* tag 'for-5.7/drivers-2020-03-29' of git://git.kernel.dk/linux-block: (81 commits)
null_blk: add trace in null_blk_zoned.c
null_blk: add tracepoint helpers for zoned mode
block: add a zone condition debug helper
nvme: cleanup namespace identifier reporting in nvme_init_ns_head
nvme: rename __nvme_find_ns_head to nvme_find_ns_head
nvme: refactor nvme_identify_ns_descs error handling
nvme-tcp: Add warning on state change failure at nvme_tcp_setup_ctrl
nvme-rdma: Add warning on state change failure at nvme_rdma_setup_ctrl
nvme: Fix controller creation races with teardown flow
nvme: Make nvme_uninit_ctrl symmetric to nvme_init_ctrl
nvme: Fix ctrl use-after-free during sysfs deletion
nvme-pci: Re-order nvme_pci_free_ctrl
nvme: Remove unused return code from nvme_delete_ctrl_sync
nvme: Use nvme_state_terminal helper
nvme: release ida resources
nvme: Add compat_ioctl handler for NVME_IOCTL_SUBMIT_IO
nvmet-tcp: optimize tcp stack TX when data digest is used
nvme-fabrics: Use scnprintf() for avoiding potential buffer overflow
nvme-multipath: do not reset on unknown status
nvmet-rdma: allocate RW ctxs according to mdts
...
Pull input fixes from Dmitry Torokhov:
- a fix to generate proper timestamps on key autorepeat events that
were broken recently
- a fix for Synaptics driver to only activate reduced reporting mode
when explicitly requested
- a new keycode for "selective screenshot" function
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix stale timestamp on key autorepeat events
Input: move the new KEY_SELECTIVE_SCREENSHOT keycode
Input: avoid BIT() macro usage in the serio.h UAPI header
Input: synaptics-rmi4 - set reduced reporting mode only when requested
Input: synaptics - enable RMI on HP Envy 13-ad105ng
Input: allocate keycode for "Selective Screenshot" key
Input: tm2-touchkey - add support for Coreriver TC360 variant
dt-bindings: input: add Coreriver TC360 binding
dt-bindings: vendor-prefixes: Add Coreriver vendor prefix
Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
FDC registers FD_STATUS, FD_DATA, FD_DOR, FD_DIR and FD_DCR used to be
defined relative to FD_IOPORT, which is the FDC's base address, itself
a macro depending on the "fdc" local or global variable.
This patch changes this so that the register macros above now only
reference the address offset, and that the FDC's address is explicitly
passed in each call to fd_inb() and fd_outb(), thus removing the macro.
With this change there is no more implicit usage of the local/global
"fdc" variable.
One place in the ARM code used to check if the port was equal to FD_DOR,
this was changed to testing the register by applying a mask to the port,
as was already done in the sparc code.
There are still occurrences of fd_inb() and fd_outb() in the PARISC
code and these ones remain unaffected since they already used to work
with a base address and a register offset.
The sparc, m68k and parisc code could now be slightly cleaned up to
benefit from the macro definitions above instead of the equivalent
hard-coded values.
Link: https://lore.kernel.org/r/20200301195555.11154-6-w@1wt.eu
Cc: Ian Molton <spyro@f2s.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
USB Raw Gadget is a kernel module that provides a userspace interface for
the USB Gadget subsystem. Essentially it allows to emulate USB devices
from userspace. Enabled with CONFIG_USB_RAW_GADGET. Raw Gadget is
currently a strictly debugging feature and shouldn't be used in
production.
Raw Gadget is similar to GadgetFS, but provides a more low-level and
direct access to the USB Gadget layer for the userspace. The key
differences are:
1. Every USB request is passed to the userspace to get a response, while
GadgetFS responds to some USB requests internally based on the provided
descriptors. However note, that the UDC driver might respond to some
requests on its own and never forward them to the Gadget layer.
2. GadgetFS performs some sanity checks on the provided USB descriptors,
while Raw Gadget allows you to provide arbitrary data as responses to
USB requests.
3. Raw Gadget provides a way to select a UDC device/driver to bind to,
while GadgetFS currently binds to the first available UDC.
4. Raw Gadget uses predictable endpoint names (handles) across different
UDCs (as long as UDCs have enough endpoints of each required transfer
type).
5. Raw Gadget has ioctl-based interface instead of a filesystem-based one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Since we expose the definition to the dt-bindings we need to keep those
definitions in sync. To address this the patch adds a simple cross
reference to the dt-bindings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just syncs the header it with the liburing version, so there's no
confusion on the license of the header parts.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have IORING_OP_PROVIDE_BUFFERS, but the only way to remove buffers
is to trigger IO on them. The usual case of shrinking a buffer pool
would be to just not replenish the buffers when IO completes, and
instead just free it. But it may be nice to have a way to manually
remove a number of buffers from a given group, and
IORING_OP_REMOVE_BUFFERS provides that functionality.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If a server process has tons of pending socket connections, generally
it uses epoll to wait for activity. When the socket is ready for reading
(or writing), the task can select a buffer and issue a recv/send on the
given fd.
Now that we have fast (non-async thread) support, a task can have tons
of pending reads or writes pending. But that means they need buffers to
back that data, and if the number of connections is high enough, having
them preallocated for all possible connections is unfeasible.
With IORING_OP_PROVIDE_BUFFERS, an application can register buffers to
use for any request. The request then sets IOSQE_BUFFER_SELECT in the
sqe, and a given group ID in sqe->buf_group. When the fd becomes ready,
a free buffer from the specified group is selected. If none are
available, the request is terminated with -ENOBUFS. If successful, the
CQE on completion will contain the buffer ID chosen in the cqe->flags
member, encoded as:
(buffer_id << IORING_CQE_BUFFER_SHIFT) | IORING_CQE_F_BUFFER;
Once a buffer has been consumed by a request, it is no longer available
and must be registered again with IORING_OP_PROVIDE_BUFFERS.
Requests need to support this feature. For now, IORING_OP_READ and
IORING_OP_RECV support it. This is checked on SQE submission, a CQE with
res == -EOPNOTSUPP will be posted if attempted on unsupported requests.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IORING_OP_PROVIDE_BUFFERS uses the buffer registration infrastructure to
support passing in an addr/len that is associated with a buffer ID and
buffer group ID. The group ID is used to index and lookup the buffers,
while the buffer ID can be used to notify the application which buffer
in the group was used. The addr passed in is the starting buffer address,
and length is each buffer length. A number of buffers to add with can be
specified, in which case addr is incremented by length for each addition,
and each buffer increments the buffer ID specified.
No validation is done of the buffer ID. If the application provides
buffers within the same group with identical buffer IDs, then it'll have
a hard time telling which buffer ID was used. The only restriction is
that the buffer ID can be a max of 16-bits in size, so USHRT_MAX is the
maximum ID that can be used.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The restriction introduced in 7a0df7fbc1 ("seccomp: Make NEW_LISTENER and
TSYNC flags exclusive") is mostly artificial: there is enough information
in a seccomp user notification to tell which thread triggered a
notification. The reason it was introduced is because TSYNC makes the
syscall return a thread-id on failure, and NEW_LISTENER returns an fd, and
there's no way to distinguish between these two cases (well, I suppose the
caller could check all fds it has, then do the syscall, and if the return
value was an fd that already existed, then it must be a thread id, but
bleh).
Matthew would like to use these two flags together in the Chrome sandbox
which wants to use TSYNC for video drivers and NEW_LISTENER to proxy
syscalls.
So, let's fix this ugliness by adding another flag, TSYNC_ESRCH, which
tells the kernel to just return -ESRCH on a TSYNC error. This way,
NEW_LISTENER (and any subsequent seccomp() commands that want to return
positive values) don't conflict with each other.
Suggested-by: Matthew Denton <mpdenton@google.com>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20200304180517.23867-1-tycho@tycho.ws
Signed-off-by: Kees Cook <keescook@chromium.org>
