Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been testing wrong variable when trying to make sure that input
allocation succeeded.
Reported by Coverity (CID 1295918).
Acked-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).
While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).
Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a kernel panic which occurs when buf_list is empty. This can
happen occasionally when user space is under heavy load (e.g. due to image
processing on the CPU) and new buffers aren't re-queued fast enough. In that
case, vb2_start_streaming_called can return true, but when the spinlock
is taken and sur40_poll attempts to fetch the next buffer from buf_list, the
list is in fact empty.
This patch needs to be applied on top of the queued one adding V4L2 support
to the sur40 driver.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the "linux,gpio-keymap" DT property is defined, the T19 keys are
configured and the device is setup as a touchpad rather than a touchscreen.
The logic is part of the input device initialization routine but it can be
factored out to its own function to simplify the former.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the new T100 object which replaces the previous T9
multitouch touchscreen object in recent maXTouch devices. T100 provides
improved reporting with selectable auxiliary information, and a type field
for hover/stylus/glove reporting.
The hovering finger support was based on Chung-Yih's work in the ChromiumOS
downstream kernel:
https://chromium-review.googlesource.com/#/c/219280/
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
[javier: Factor out T9 and T100 init functions and rework hover support]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds raw video support for the Samsung SUR40 using vbuf2-dma-sg.
All tests from v4l2-compliance pass. Support for VB2_USERPTR is currently
disabled due to unexpected interference with dma-sg buffer sizes.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix compile warning: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Eliminate redundant calculations by performing millisecond to jiffy
calculations once during driver initialization.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_register_device already sets the EV_SYN event since all devices can
generate them.
Remove the redundant affectation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the driver relies on some obscure and undocumented register to set
the maximum axis value.
The reported value is way too high to be meaningful, which confuses some
userspace tools like QT's evdevtouch plugin which try to scale the reported
events to the maximum values.
Use the values from the DT to set meaningful values.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So far, the DT parsing code was only setting up the regular input axes,
completely ignoring their multitouch counter parts.
Fill them with the same parameters than the regular axes.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The DT parsing function currently duplicates a lot of the code to parse the
touchscreen DT properties. In order to ease further additions to this
parsing routine, rework it slightly to create new helper functions.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChipOne icn8318 is an i2c capacitive touchscreen controller typically
used in cheap android tablets, this commit adds a driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for another model of IRTOUCH SYSTEMS Co.,LtD infrared
touchscreens. The USB vendorID/deviceID is 6615/0012. It is also sold
under the label "Elektrosil".
The datasheet states that coordinates for x and y are in the range from
0 to 32767.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit introduces two new optional device-tree properties:
"tp-sensitive-adjust": adjust sensitivity of pen down detection
"filter-type": select median and averaging filter
The previous fixed defaults, didn't work well for the Olimex
A13-LCD10TS (I have).
Signed-off-by: Jens Thiele <karme@karme.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_device_id is always used as const argument (See driver.of_match_table
and open firmware functions).
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The commit titled: "Input: sun4i-ts - A10 (sun4i) has a different
temperature curve" contains a math error, the offset it uses is in degrees,
but the actual code applies the offset before multiplying by stepsize :|
Given that this is rather backwards (every math course ever thought applies
the multiplication before the offset for linear functions), this commit
fixes things by changing the code applying the offset to do the logical
thing, adjusting the offset for the other models accordingly.
This has been tested on an A10, A13, A20 and A31 to make sure everything
really is correct now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
