When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Device unit for port buffers size, xoff_threshold and xon_threshold is
cells. Fix a bug in driver where cell unit size was hard-coded to
128 bytes. This hard-coded value is buggy, as it is wrong for some hardware
versions.
Driver to read cell size from SBCAM register and translate bytes to cell
units accordingly.
In order to fix the bug, this patch exposes SBCAM (Shared buffer
capabilities mask) layout and defines.
If SBCAM.cap_cell_size is valid, use it for all bytes to cells
calculations. If not valid, fallback to 128.
Cell size do not change on the fly per device. Instead of issuing SBCAM
access reg command every time such translation is needed, cache it in
mlx5e_dcbx as part of mlx5e_dcbnl_initialize(). Pass dcbx.port_buff_cell_sz
as a param to every function that needs bytes to cells translation.
While fixing the bug, move MLX5E_BUFFER_CELL_SHIFT macro to
en_dcbnl.c, as it is only used by that file.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15:
warning: memset with byte count of 271720
mlx5_cmd_stats array is too big to be held inline in mlx5_cmd.
Allocate it separately.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
From the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in following patches
* branch 'mellanox/mlx5-next':
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The end result of RDMA-CM ECE handshake is ECE options, which is
needed to be used while configuring data QPs. Such options can
come in any QP state, so add in/out fields to set and query
ECE options.
OUT fields:
* create_qp() - default ECE options for that type of QP.
* modify_qp() - enabled ECE options after QP state transition.
IN fields:
* create_qp() - create QP with this ECE option.
* modify_qp() - requested options. For unconnected QPs, the FW
will return an error if ECE is already configured with any options
that not equal to previously set.
Reviewed-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is reloading during recovery flow, it can't get new commands
till command interface is up again. Otherwise we may get to null pointer
trying to access non initialized command structures.
Add cmdif state to avoid processing commands while cmdif is not ready.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After driver creates (via FW command) an EQ for commands, the driver will
be informed on new commands completion by EQE. However, due to a race in
driver's internal command mode metadata update, some new commands will
still be miss-handled by driver as if we are in polling mode. Such commands
can get two non forced completion, leading to already freed command entry
access.
CREATE_EQ command, that maps EQ to the command queue must be posted to the
command queue while it is empty and no other command should be posted.
Add SW mechanism that once the CREATE_EQ command is about to be executed,
all other commands will return error without being sent to the FW. Allow
sending other commands only after successfully changing the driver's
internal command mode metadata.
We can safely return error to all other commands while creating the command
EQ, as all other commands might be sent from the user/application during
driver load. Application can rerun them later after driver's load was
finished.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When FW response to commands is very slow and all command entries in
use are waiting for completion we can have a race where commands can get
timeout before they get out of the queue and handled. Timeout
completion on uninitialized command will cause releasing command's
buffers before accessing it for initialization and then we will get NULL
pointer exception while trying access it. It may also cause releasing
buffers of another command since we may have timeout completion before
even allocating entry index for this command.
Add entry handling completion to avoid this race.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Only mlx5_core driver handles fw initialization check and command
interface revision check.
Hence move them inside the mlx5_core driver where it is used.
This avoid exposing these helpers to all mlx5 drivers.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the "metadata_reg_b" field and all uses of this field in code
to match the device specification. As this field is not in use in SW
steering it is safe to remove it.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
From the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in following patches
* branch 'mellanox/mlx5-next':
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently, fs_core supports rule of forward the traffic
to continue matching in the next priority, now we add support
to forward the traffic matching in the next namespace.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge includes updates to bonding driver needed for the rdma stack,
to avoid conflicts with the RDMA branch.
Maor Gottlieb Says:
====================
Bonding: Add support to get xmit slave
The following series adds support to get the LAG master xmit slave by
introducing new .ndo - ndo_get_xmit_slave. Every LAG module can
implement it and it first implemented in the bond driver.
This is follow-up to the RFC discussion [1].
The main motivation for doing this is for drivers that offload part
of the LAG functionality. For example, Mellanox Connect-X hardware
implements RoCE LAG which selects the TX affinity when the resources
are created and port is remapped when it goes down.
The first part of this patchset introduces the new .ndo and add the
support to the bonding module.
The second part adds support to get the RoCE LAG xmit slave by building
skb of the RoCE packet based on the AH attributes and call to the new
.ndo.
The third part change the mlx5 driver driver to set the QP's affinity
port according to the slave which found by the .ndo.
====================
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The patch sets the lag tx affinity of the data QPs and the GSI QPs
according to the LAG xmit slave.
For GSI QPs, in case the link layer is Ethenet (RoCE) we create two GSI
QPs, one for each physical port. When the driver selects the GSI QP, it
will consider the port affinity result. For connected QPs, the driver
sets the affinity of the xmit slave.
The above, ensures that RC QP and it's corresponding GSI QP will transmit
from the same physical port.
Link: https://lore.kernel.org/r/20200430192146.12863-17-maorg@mellanox.com
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
mlx5 updates for both net-next and rdma-next:
1) HW bits and definitions for TLS and IPsec offlaods
2) Release all pages capability bits
3) New command interface helpers and some code cleanup as a result
4) Move qp.c out of mlx5 core driver into mlx5_ib rdma driver
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new TX WQE field for Connect-X6DX trailer insertion support,
when set, the HW adds a trailer to the packet, the WQE trailer
association flags are used to set to HW the header which the
trailer belongs.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Ron Diskin
Eran Ben Elisha
Leon Romanovsky
Linus Torvalds
Saeed Mahameed
Jason Gunthorpe
David S. Miller
Moshe Shemesh
Parav Pandit
Raed Salem
Maor Gottlieb
Gustavo A. R. Silva