Add new rate estimator target (using gen_estimator). In combination with
the rateest match (next patch) this can be used for load-based multipath
routing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_DSCP target by xt_TOS v1 to add support for selectively
setting and flipping any bit in the IPv4 TOS and IPv6 Priority fields.
(ipt_TOS and xt_DSCP only accepted a limited range of possible
values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the xt_dscp match by xt_tos v1 to add support for selectively
matching any bit in the IPv4 TOS and IPv6 Priority fields. (ipt_tos
and xt_dscp only accepted a limited range of possible values.)
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addrtype match has a new revision (1), which lets address type checking
limited to the interface the current packet belongs to. Either incoming
or outgoing interface can be used depending on the current hook. In the
FORWARD hook two maches should be used if both interfaces have to be checked.
The new structure is ipt_addrtype_info_v1.
Revision 0 lets older userspace programs use the match as earlier.
ipt_addrtype_info is used.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_owner merges ipt_owner and ip6t_owner, and adds a flag to match
on socket (non-)existence.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a big array of NR_CPUS entries, we can compute the size
needed at runtime, using nr_cpu_ids
This should save some ram (especially on David's machines where NR_CPUS=4096 :
32 KB can be saved per table, and 64KB for dynamically allocated ones (because
of slab/slub alignements) )
In particular, the 'bootstrap' tables are not any more static (in data
section) but on stack as their size is now very small.
This also should reduce the size used on stack in compat functions
(get_info() declares an automatic variable, that could be bigger than kernel
stack size for big NR_CPUS)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the basic infrastructure for per namespace sysctls.
A list of lists of sysctl headers is added, allowing each namespace to have
it's own list of sysctl headers.
Each list of sysctl headers has a lookup function to find the first
sysctl header in the list, allowing the lists to have a per namespace
instance.
register_sysct_root is added to tell sysctl.c about additional
lists of sysctl_headers. As all of the users are expected to be in
kernel no unregister function is provided.
sysctl_head_next is updated to walk through the list of lists.
__register_sysctl_paths is added to add a new sysctl table on
a non-default sysctl list.
The only intrusive part of this patch is propagating the information
to decided which list of sysctls to use for sysctl_check_table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By doing this we allow users of register_sysctl_paths that build
and dynamically allocate their ctl_table to be simpler. This allows
them to just remember the ctl_table_header returned from
register_sysctl_paths from which they can now find the
ctl_table array they need to free.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a number of modules that register a sysctl table
somewhere deeply nested in the sysctl hierarchy, such as
fs/nfs, fs/xfs, dev/cdrom, etc.
They all specify several dummy ctl_tables for the path name.
This patch implements register_sysctl_path that takes
an additional path name, and makes up dummy sysctl nodes
for each component.
This patch was originally written by Olaf Kirch and
brought to my attention and reworked some by Olaf Hering.
I have changed a few additional things so the bugs are mine.
After converting all of the easy callers Olaf Hering observed
allyesconfig ARCH=i386, the patch reduces the final binary size by 9369 bytes.
.text +897
.data -7008
text data bss dec hex filename
26959310 4045899 4718592 35723801 2211a19 ../vmlinux-vanilla
26960207 4038891 4718592 35717690 221023a ../O-allyesconfig/vmlinux
So this change is both a space savings and a code simplification.
CC: Olaf Kirch <okir@suse.de>
CC: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the defines again, convert to the new checksum helper names and
remove the dependency of NET_ACT_NAT on NETFILTER.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to get rid of the CONFIG_NETFILTER dependency of NET_ACT_NAT.
This patch redefines the old names to keep the noise low, the next patch
converts all users.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary state transitions for the two forms of passive-close
* PASSIVE_CLOSE - which is entered when a host receives a Close;
* PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq.
Here is a detailed account of what the patch does in each state.
1) Receiving CloseReq
The pseudo-code in 8.5 says:
Step 13: Process CloseReq
If P.type == CloseReq and S.state < CLOSEREQ,
Generate Close
S.state := CLOSING
Set CLOSING timer.
This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN.
* CLOSED: silently ignore - it may be a late or duplicate CloseReq;
* LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client);
* REQUEST: perform Step 13 directly (no need to enqueue packet);
* OPEN/PARTOPEN: enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data.
When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored.
I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where
the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it
gets the Reset, so ignoring the CloseReq while in state CLOSING is sane.
2) Receiving Close
The code below from 8.5 is unconditional.
Step 14: Process Close
If P.type == Close,
Generate Reset(Closed)
Tear down connection
Drop packet and return
Thus we need to consider all states:
* CLOSED: silently ignore, since this can happen when a retransmitted or late Close arrives;
* LISTEN: dccp_rcv_state_process() will generate a Reset ("No Connection");
* REQUEST: perform Step 14 directly (no need to enqueue packet);
* RESPOND: dccp_check_req() will generate a Reset ("Packet Error") -- left it at that;
* OPEN/PARTOPEN: enter PASSIVE_CLOSE so that application has a chance to process unread data;
* CLOSEREQ: server performed active-close -- perform Step 14;
* CLOSING: simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment);
* PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close);
* TIMEWAIT: packet is ignored.
Note that the condition of receiving a packet in state CLOSED here is different from the condition "there
is no socket for such a connection": the socket still exists, but its state indicates it is unusable.
Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that
sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two auxiliary states to deal with passive closes:
* PASSIVE_CLOSE (reached from OPEN via reception of Close) and
* PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq)
as internal intermediate states.
These states are used to allow a receiver to process unread data before
acknowledging the received connection-termination-request (the Close/CloseReq).
Without such support, it will happen that passively-closed sockets enter CLOSED
state while there is still unprocessed data in the queue; leading to unexpected
and erratic API behaviour.
PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will
seamlessly work with inet_accept() (which tests for this state).
The state names are thanks to Arnaldo, who suggested this naming scheme
following an earlier revision of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.
This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.
I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.
I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I keep getting this build error and couldn't find anyone fixing
it in archives. ...Maybe all net developers except me build
just SMP kernels :-).
In file included from include/net/sock.h:50,
from ipc/mqueue.c:35:
include/linux/pcounter.h: In function 'pcounter_add':
include/linux/pcounter.h:87: error: 'struct pcounter' has no
member named 'value'
make[1]: *** [ipc/mqueue.o] Error 1
make: *** [ipc] Error 2
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This decouples PARTOPEN from TCP-specific stream-states.
It thus addresses the FIXME.
The code has been checked with regard to dependency on PARTOPEN and FIN_WAIT1
states (to which PARTOPEN previously was mapped): there is no difference, as
PARTOPEN is always referred to directly (i.e. not via the mapping to TCP
state).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just generalises what was introduced by Eric Dumazet for the struct proto
inuse field in 286ab3d460:
[NET]: Define infrastructure to keep 'inuse' changes in an efficent SMP/NUMA way.
Please look at the comment in there to see the rationale.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds several structs and definitions to ieee80211.h
to support 802.11n draft specifications.
As 802.11n depends on and extends the 802.11e standard in several issues,
there are also several definitions that belong to 802.11e.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.
Changes from v2:
- IPv6 addrlabel processing
Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IEEE80211_MAX_FRAME_LEN which is useful for drivers trying
to determine how much to allocate for their RX buffers.
It also updates the comment on IEEE80211_MAX_DATA_LEN based on revisions
in 802.11e.
IEEE80211_MAX_FRAG_THRESHOLD and IEEE80211_MAX_RTS_THRESHOLD are also
revised due to the new maximum frame size.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_flags variable is redundant. Turning rx on/off is done
via setting the rx_np pointer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local_mac is managed by the network device, no need to keep a
spare copy and all the management problems that could cause.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
