Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have CONFIG_BLACKFIN ifdef redefining all musb registers in
musb_regs.h and tusb6010.h is never included causing a build
error with blackfin-allmodconfig and COMPILE_TEST.
Let's fix the issue by not building tusb6010 if CONFIG_BLACKFIN
is selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for Infineon flashloader 0x8087/0x0801.
The flashloader is used in Telit LE940B modem family with Telit
flashing application.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Felipe writes:
usb: fixes for v4.8-rc6
Unfortunately we have a bogus dwc3 patch leaked through the cracks and
got merged into Linus' HEAD. That patch ended up causing off-by-1 error
in our TRB accounting logic. Thankfully John Youn found out the problem
and we provided a revert to the bogus dwc3 patch in no time.
Apart from this off-by-1 error, we have two fixes to the Renesas drivers,
a small fix to our generic phy driver, a NULL pointer dereference fix for
f_eem and a build warning fix in dwc3.
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Cc: <stable@vger.kernel.org> #4.1+
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building a kernel with CONFIG_PM_SLEEP=n, we
get the following warning:
drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used
In order to fix this, we should only define
dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined.
Fixes: f6c274e11e ("usb: dwc3: pci: runtime_resume child device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An earlier fix partially fixed the null pointer dereference on skb->len
by moving the assignment of len after the check on skb being non-null,
however it failed to remove the erroneous dereference when assigning len.
Correctly fix this by removing the initialisation of len as was
originally intended.
Fixes: 70237dc8ef ("usb: gadget: function: f_eem: socket buffer may be NULL")
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
Fixes: d5c6a1e024 ("usb: renesas_usbhs: fixup interrupt status clear method")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
clk_prepare_enable() may fail, so we should better check its return
value and propagate it in the case of failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver should clear the bit. Otherwise, the VBUS will output
wrongly if the usb port on a board has VBUS output capability.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for
Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 6f8245b4e3 ("usb: dwc3: gadget: always decrement
by 1").
We can't always decrement this value.
We should decrement only if the calculation of free slots results in a
LINK TRB being among one of the free slots (dequeue < enqueue).
Otherwise, if the LINK TRB is not among the free slots then it should
not be decremented.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we have USB gadgets disabled and USB_MUSB_HOST set, we get
errors "possible irq lock inverssion dependency detected"
errors during boot.
Let's fix the issue by adding start_musb flag and start
the controller after we're out of the spinlock protected
section.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
Fix one bug that host can't work after insmod gadget module
at dual-role mode, the root cause of this issue is the usbcmd.rs
is cleared by chipidea udc code.
Johan writes:
USB-serial fixes for v4.8-rc4
Here are a couple of fixes for non-atomic allocations in write paths,
and some new option device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Felipe writes:
usb: fixes for v4.8-rc3
Few fixes on dwc3 again, the most important being a
fix for pm_runtime to make it work with current
intel platforms.
Other than that, there's a signedness bug fix in fsl
udc and some other minor fixes.
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb gadget is set gadget serial function, it will be crash in below
situation.
It will clean the 'port->port_usb' pointer in gserial_disconnect() function
when usb link is inactive, but it will release lock for disabling the endpoints
in this function. Druing the lock release period, it maybe complete one request
to issue gs_write_complete()--->gs_start_tx() function, but the 'port->port_usb'
pointer had been set NULL, thus it will be crash in gs_start_tx() function.
This patch adds the 'port->port_usb' pointer checking in gs_start_tx() function
to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
