Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
V1F indicates that the time accuracy may have been compromised because
of a voltage drop (possibly only temporary) below VLOW1, which stops the
temperature compensation. When the time is set, the accuracy is
restored, so V1F should be cleared in order to indicate this and to be
able to detect the next temperature compensation loss. This is the same
principle as for V2F, which is cleared when the time is set to indicate
that the time is no longer invalid and to be able to detect the next
data loss.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the application manual of the RX8900, the RESET bit must be
set to 1 to prevent a timer update while setting the time. This also
resets the subsecond counter. The application manual of the RV-8803 does
not mention such a requirement, and it says that the 100th Seconds
register is cleared when writing to the Seconds register, but using the
RESET bit for the RV-8803 too should not be an issue and is probably
safer.
This change also ensures that the RESET bit is initialized properly in
all cases. Indeed, all the registers must be initialized if the voltage
has been lower than VLOW2 (triggering V2F), but not low enough to
trigger a POR.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The I²C NACK issue of the RV-8803 may occur after any I²C START
condition, depending on the timings. Consequently, the workaround must
be applied for all the I²C transfers.
This commit abstracts the I²C transfer code into register access
functions. This avoids duplicating the I²C workaround everywhere. This
also avoids the duplication of the code handling the return value of
i2c_smbus_read_i2c_block_data(). Error messages are issued in case of
definitive register access failures (if the workaround fails). This
change also makes the I²C transfer return value checks consistent.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Weekday register is encoded as 2^tm_wday, with tm_wday in 0..6, so
using tm_wday = ffs(reg) to fill tm_wday from the register value is
wrong because this gives the expected value + 1. This could be fixed as
tm_wday = ffs(reg) - 1, but tm_wday = ilog2(reg) works as well and is
more direct.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC core always calls rtc_valid_tm() after ->read_time() in case of
success (in __rtc_read_time()), so do not call it twice.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current rtc-pcf85063 driver only supports the PCF85063TP device.
Using the existing driver on a PCF85063A will result in the time being
set correctly into the RTC, but the RTC is held in the stopped state.
Therefore, the time will no longer advance and no error is indicated.
The PCF85063A device has a bigger memory map than the PCF85063TP.
The existing driver make use of an address rollover condition,
but the rollover point is different in the two devices.
Signed-off-by: Chris DeBruin <cdeb5783@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The year range is not validated properly
As the driver has been mainlined in 2014, it is not an issue to stop
handling dates between 1970 and 2000 with the benefit of handling dates up
to 2100.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since all time members of the alarm data is initialized to -1 the drivers
are responsible to set the tm_sec member to 0.
Fixes: d68778b80d ("rtc: initialize output parameter for read alarm to "uninitialized"")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
clk_prepare_enable(info->rtc_clk) // rtc clock enabled
s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
s3c_rtc_setfreq() //then this will be called with clk disabled
This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().
Fixes: 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock control")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If devm_add_action() fails we are explicitly calling the cleanup to free
the resources allocated. Lets use the helper devm_add_action_or_reset()
and return directly in case of error, as we know that the cleanup function
has been already called by the helper if there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If devm_add_action() fails we are explicitly calling the cleanup to free
the resources allocated. Lets use the helper devm_add_action_or_reset()
and return directly in case of error, as we know that the cleanup function
has been already called by the helper if there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some QNAP NAS devices the rtc can wake the machine. Several people
noticed that once the machine was woken this way it fails to shut down.
That's because the driver fails to acknowledge the interrupt and so it
keeps active and restarts the machine immediatly after shutdown. See
https://bugs.debian.org/794266 for a bug report.
Doing this correctly requires to interpret the INT2 flag of the first read
of the STATUS1 register because this bit is cleared by read.
Note this is not maximally robust though because a pending irq isn't
detected when the STATUS1 register was already read (and so INT2 is not
set) but the irq was not disabled. But that is a hardware imposed problem
that cannot easily be fixed by software.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There were two deviations from the reference manual: you have to wait
half a second when POC is active and you might have to repeat
initialization when POC or BLD are still set after the sequence.
Note however that as POC and BLD are cleared by read the driver might
not be able to detect that a reset is necessary. I don't have a good
idea how to fix this.
Additionally report the value read from STATUS1 to the caller. This
prepares the next patch.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are several issues fixed in this patch:
- When alarm isn't enabled, set .enabled to zero instead of returning
-EINVAL.
- Ignore how IRQ1 is configured when determining if IRQ2 is on.
- The three alarm registers have an enable flag which must be
evaluated.
- The chip always triggers when the seconds register gets 0.
Note that the rtc framework however doesn't handle the result correctly
because it doesn't check wday being initialized and so interprets an
alarm being set for 10:00 AM in three days as 10:00 AM tomorrow (or
today if that's not over yet).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc core doesn't give broken dates to a driver's .set_alarm
callback, so there should be no need for validation.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
