Pull regmap fix from Mark Brown:
"A fix for an issue with double locking that was introduced earlier
this release. I'd missed in review that we were already in a locked
region when trying to drop part of the cache"
* tag 'regmap-fix-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix deadlock on _regmap_raw_write() error path
Commit 815806e39b ("regmap: drop cache if the bus transfer error")
added a call to regcache_drop_region() to error path in
_regmap_raw_write(). However that path runs with regmap lock taken,
and regcache_drop_region() tries to re-take it, causing a deadlock.
Fix that by calling map->cache_ops->drop() directly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_write
->_regmap_raw_write
-->regcache_write first and than use map->bus->write to wirte i2c or spi
But if the i2c or spi transfer failed, But the cache is updated, So if I use
regmap_read will get the cache data which is not the real register value.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When searching for a suitable node that should be used for inserting a new
register, which does not fall within the range of any existing node, we not
only looks for nodes which are directly adjacent to the new register, but
for nodes within a certain proximity. This is done to avoid creating lots
of small nodes with just a few registers spacing in between, which would
increase memory usage as well as tree traversal time.
This means there might be multiple node candidates which fall within the
proximity range of the new register. If we choose the first node we
encounter, under certain register insertion patterns it is possible to end
up with overlapping ranges. This will break order in the rbtree and can
cause the cached register value to become corrupted.
E.g. take the simplified example where the proximity range is 2 and the
register insertion sequence is 1, 4, 2, 3, 5.
* Insert of register 1 creates a new node, this is the root of the rbtree
* Insert of register 4 creates a new node, which is inserted to the right
of the root.
* Insert of register 2 gets inserted to the first node
* Insert of register 3 gets inserted to the first node
* Insert of register 5 also gets inserted into the first node since
this is the first node encountered and it is within the proximity range.
Now there are two overlapping nodes.
To avoid this always choose the node that is closest to the new register.
This will ensure that nodes will not overlap. The tree traversal is still
done as a binary search, we just don't stop at the first node found. So the
complexity of the algorithm stays within the same order.
Ideally if a new register is in the range of two adjacent blocks those
blocks should be merged, but that is a much more invasive change and left
for later.
The issue was initially introduced in commit 472fdec738 ("regmap: rbtree:
Reduce number of nodes, take 2"), but became much more exposed by commit
6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target
node") which changed the order in which nodes are looked-up.
Fixes: 6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target node")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 3245d460 (regmap: cache: Fall back to register by register read for
cache defaults) non-readable registers are skipped when initializing
reg_defaults, but are still included in num_reg_defaults. So there can
be uninitialized entries at the end of reg_defaults, which can cause
problems when the register cache initializes from the full array.
Fixed it by excluding non-readable registers from the count as well.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When doing a bulk writes from a device which lacks raw I/O support we
fall back to doing register at a time reads but we still use the raw
formatters in order to render the data into the word size used by the
device (since bulk reads still operate on the device word size rather
than unsigned ints). This means that devices without raw formatting
such as those that provide reg_read() are not supported. Provide
handling for them by copying the values read into native endian values
of the appropriate size.
This complements commit d5b98eb124 ("regmap: Support bulk reads for
devices without raw formatting").
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Chips with 16-bit registers don't usually work well with I2C block
commands. For example, neither the LM75 datasheet nor the TMP102 datasheet
mentions block command support, and in fact it does not work for any of
those chips. Also, it is not clear how the block command would handle
16-bit SMBus operations in the fist place, since the data format associated
with those commands is either little endian or big endian, which requires
some kind of conversion to or from host byte order.
Only use i2c block commands if both register and value width is 8 bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regmap irq implements the generic interrupt service routine which
is common for most of devices. Some devices, like MAX77620, MAX20024
needs the special handling before and after servicing the interrupt
as generic. For the example, MAX77620 programming guidelines for
interrupt servicing says:
1. When interrupt occurs from PMIC, mask the PMIC interrupt by setting
GLBLM.
2. Read IRQTOP and service the interrupt accordingly.
3. Once all interrupts has been checked and serviced, the interrupt
service routine un-masks the hardware interrupt line by clearing
GLBLM.
The step (2) is implemented in regmap irq as generic routine. For
step (1) and (3), add callbacks from regmap irq to client driver
to handle chip specific configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specifically for the case of reads that use the Extended Register
Read Long command, a multi-byte read operation is broken up into
8-byte chunks. However the call to spmi_ext_register_readl() is
incorrectly passing 'val_size', which if greater than 8 will
always fail. The argument should instead be 'len'.
Fixes: c9afbb05a9 ("regmap: spmi: support base and extended register spaces")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Otherwise the DT parsing will default to big endian if nothing is
specified.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we changed to do formatting in the bus we now skip all the format
parsing that the core does for its data marshalling code. This means
that we skip the DT parsing it does which breaks some systems, we need
to add an explict call in the MMIO code to do this.
Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
internal.h is using dev_name() but doesn't include device.h which
defines it. Add an explicit include to avoid build problems due to
this.
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If max_register is unset, regcache_flat_get_index will return 0 and only
memory for 1 unsigned int will be allocated, resulting in writing out
of bounds.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the flag 'cache_bypass' will bypass the cache not the hardware.
Fix this comment here.
Fixes: 0eef6b0415 ("regmap: Fix doc comment")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device managed APIs for regmap_add_irq_chip() and
regmap_del_irq_chip() so that it can be managed by
device framework for freeing it.
This helps on following:
1. Maintaining the sequence of resource allocation and deallocation
regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq)
On free path:
regmap_del_irq_chip(d);
and then removing the irq registration.
On this case, regmap irq is deleted before the irq is free.
This force to use normal irq registration.
By using devm apis, the sequence can be maintain properly:
devm_regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq);
and resource deallocation will be done in reverse order
by device framework.
2. No need to delete the regmap_irq_chip in error path or remove
callback and hence there is less code on this path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 23b92e4cf5fd ("regmap: remove regmap_write_bits()")
removed regmap_write_bits(), but MFD driver was using it.
So, commit e30fccd6771d ("regmap: Keep regmap_write_bits()")
turns out it, but it is using original style.
This patch uses regmap_update_bits_base() for regmap_write_bits()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
