These patches get us closer to adding multiplatform support on
the Exynos platform, they are part of a longer series of
patches. This would get all the simple stuff out of the
way, and I don't think there is a big risk of introducing
regressions with these.
A lot of the other patches have already been merged into
subsystem trees. After this series in in arm-soc, what is
left comes down to
* The ASoC conversion to dmaengine won't make it unless someone
who knows that code better steps up to do it right away. This
means that we won't have audio in a 3.10 multiplatform kernel
on Exynos, but it will still work for users that don't enable
multiplatform.
* The irqchip (combiner), clk and clksource patches are all based
on top of other changesets we pulled in from your trees, so I
would not make them part of the next/multiplatform branch. We can
apply them on top of the next/drivers branch once they are
tested successfully.
* A trivial patch is needed in the end to actually make
CONFIG_ARCH_EXYNOS visible in multiplatform configurations.
We will do that as a separate patch once everything else is
there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
plat/regs-sdhci.h is not used anywhere but in the sdhci-s3c
driver, so it can become a local file there and all other
inclusions removed.
plat/sdhci.h is used only to define the platform devices,
and with the exception of the platform_data structure not
needed by the driver, so we can split out the platform_data
definition instead and leave the rest to platform code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Typical usage of pdata.init/exit is enable/disable power and/or toggle
reset for the target chip.
This patch replaces these callbacks with regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for platform specific data for SDIO
fullmac devices. Currently OOB interrupts are configured by Kconfig
BRCMFMAC_SDIO_OOB but that is now determined dynamically by checking
availibility of platform data.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a common clock driver for Silicon Labs Si5351a/b/c
i2c programmable clock generators. Currently, the driver does not
support VXCO feature of si5351b. Passing platform_data or DT bindings
selectively allows to overwrite stored Si5351 configuration which is
very helpful for clock generators with empty eeprom configuration.
Corresponding device tree binding documentation is also added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Michal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The spi-s3c64xx uses a Samsung proprietary interface for
talking to the DMA engine, which does not work with
multiplatform kernels.
This version of the patch leaves the old code in place,
behind an #ifdef. This can be removed in the future,
after the s3c64xx platform start supporting the regular
dmaengine interface. An earlier version of this patch was
tested successfully on exynos5250 by Padma Venkat.
The conversion was rather mechanical, since the samsung
interface is just a shallow wrapper around the dmaengine
interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The s3c-fb driver requires header files from the samsung platforms
to find its platform_data definition, but this no longer works on
multiplatform kernels, so let's move the data into a new header
file under include/linux/platform_data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-fbdev@vger.kernel.org
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch changes the name of USB ohci header from 'usb-exynos.h'
to 'usb-ohci-exynos.h'. This is because this header file has
the platdata for only EXYNOS OHCI.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This header file only contains platform data structure definitions,
so it's straightforward to move.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Delete one include rather than move it]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.
Basically we are left with the two alternatives of code
placement as:
- arch/arm/mach-ux500/pm.c - this because the code is
closely related to the GIC, and takes ownership of
some of the registers from the PRCMU related to this
PM functionality.
- drivers/mfd/db8500-prcmu-pm.c - because the code is
affecting stuff in the PRCMU register range. But then
this code needs to remap and handle GIC registers.
This patch implementation is taking the first approach.
Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.
The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds DT support to NTC driver to parse the
platform data.
Also adds the support to work as an iio device client.
During the probe ntc driver gets the respective channels of ADC
and uses iio_raw_read calls to get the ADC converted value.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[Guenter Roeck: fixed Kconfig dependencies; use ERR_CAST]
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In case the driver is not probed - due to config mismatches or errors
in the DTS files - dev_get_drvdata() returns NULL, leading to an Ooops
during boot.
Make elm_config() return an error in such cases to propagate the error
up to the user, so it can fall back to software mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With the conversion to devicetree only for arch-vt8500, this
header is no longer required. This patch removes the #include
from the two framebuffer drivers that used it, and the header file.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove specifying mmc controller IP version information via platform
data, instead specify device name so that driver derives it from
platform_device_id table. Also change the clock node name to match
the changed dev_id.
Tested on da850-evm to make sure driver loads without clk_get failures.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Using pdata to pass clock name is not correct.
Directly get clock from usb drivers.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now LP55xx provides automatic clock detection API, lp55xx_is_extclk_used().
The clock configuration can be done by the driver itself.
(a) Concept
The default value is set by each driver with clock selection.
The internal clock selection bit is updated in case that the external clock
is not detected or clock rate is not 32KHz.
(b) Change on LP55xx platform data
The clock configuration is done automatically, so no need to define
'update_config' in the platform side.
Correlated information are removed in the documentations and header.
(c) Definitions moved from header to driver files
CONFIG register values are moved each driver, LP5521 and LP5562.
Not necessary definitions are removed also.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5562 can drive up to 4 channels, RGB and White.
LEDs can be controlled directly via the led class control interface.
LP55xx common driver
LP5562 is one of LP55xx family device, so LP55xx common code are used.
On the other hand, chip specific configuration is defined in the structure
'lp55xx_device_config'
LED pattern data
LP5562 has also internal program memory which is used for running various LED
patterns. LP5562 driver supports the firmware interface and the predefined
pattern data as well.
LP5562 device attributes: 'led_pattern' and 'engine_mux'
A 'led_pattern' is an index code which runs the predefined pattern data.
And 'engine_mux' is updated with the firmware interface is activated.
Detailed description has been updated in the documentation files,
'leds-lp55xx.txt' and 'leds-lp5562.txt'.
Changes on the header file
LP5562 configurable definitions are added.
Pattern RGB data is fixed as constant value.
(No side effect on other devices, LP5521 or LP5523.)
(cooloney@gmail.com: remove redundant mutex_unlock(). Reported by Dan
Carpenter <dan.carpenter@oracle.com>)
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
As per JESD209-2E specification for LPDDR2,
http://www.jedec.org/standards-documents/results/jesd209-2E
Table 73, LPDDR2 memories come in two flavors - Standard and
Extended. The Standard types can operate from -25C to +85C
However, beyond that and upto +105C can only be supported by
Extended types.
Unfortunately, it seems there is no info in MR0(device info) or
MR[1,2](device feature) for run time detection of this capability
as far as seen on the spec. Hence, we provide a custom_config
flag to be populated by platforms which have these "extended"
type memories.
For the "Standard" memories, we need to consider MR4 notifications
of temperature triggers >85C as equivalent to thermal shutdown
events (equivalent to Spec specified thermal shutdown events for
"extended" parts).
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann
Alexander Shiyan
Bastian Hecht
Tomi Valkeinen
Hante Meuleman
Sebastian Hesselbarth
Jingoo Han
Linus Walleij
Guenter Roeck
Naveen Krishna Chatradhi
Daniel Mack
Tony Prisk
Manjunathappa, Prakash
Laurent Pinchart
Magnus Damm
Chao Xie
Kim, Milo
Nishanth Menon