On Thu, May 28, 2009 at 10:59 AM, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> On Thu, May 28, 2009 at 07:15:16AM +0200, Philipp Zabel wrote:
>> The V3 regulator can be configured with an external resistor
>> connected to the feedback pin (R24 in the data sheet) to
>> increase the voltage range.
>>
>> For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
>> V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
>>
>> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
>
> Looks good.
>
> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Thanks, but it turns out I hit a 32 bit integer overflow in
the gain calculation. I'd like to mend that with the following
patch. Now max_uV could be increased up to 4.294 V, enough to
charge LiPo cells.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.
For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
lp3971_i2c_remove' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.devexit.text' of drivers/built-in.o
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Several of the regulator drivers didn't have MODULE_ALIAS so couldn't be
auto loaded. Add the MODULE_ALIAS in case they do get built as modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Regulators need to be available early in init in order to allow them
to be available for consumers when requested. This is generally done
by registering them at subsys_initcall() time but not all regulator
drivers have done that. Convert these drivers to do so in order to
mimimise future support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes the follwing build failure on powerpc:-
> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> drivers/regulator/userspace-consumer.c:43: error: conflicting types
> for 'show_state'
> include/linux/sched.h:273: note: previous definition of 'show_state'
> was here
>
> Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator:
> add userspace-consumer driver") which I have reverted for today.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.
The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Default voltage constraints were being provided for fixed voltage
regulator where board constraints were not provided but these constraints
used INT_MIN as the default minimum voltage which is not a valid value
since it is less than zero. Use 1uV instead.
Also set the default values we set in the constraints themselves since
otherwise the max_uV constraint we determine will not be stored in the
actual constraint strucutre and will therefore not be used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This seems to be fallout from last October's regulator core rework.
It got noticed only because of recent regulator framework changes.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
During regulator registration, any error after device_register() will
cause a double-free on the struct regulator_dev 'rdev'. The bug is in
drivers/regulator/core.c:regulator_register():
...
scrub:
device_unregister(&rdev->dev);
clean:
kfree(rdev); <---
rdev = ERR_PTR(ret);
goto out;
...
device_unregister() calls regulator_dev_release() which frees rdev. The
subsequent kfree corrupts memory and causes some OMAP3 systems to oops on
boot in regulator_get().
Applies against 2.6.30-rc3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When regulator_desc->type is something different from REGULATOR_VOLTAGE or REGULATOR_CURRENT
the if should probably return ERR_PTR(-EINVAL)
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@@ expression E; constant C; @@
(
- !E == C
+ E != C
)
Signed-off-by: Diego Liziero <diegoliz@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
At present it is not possible for machine constraints to disable
regulators which have been left on when the system starts, for example
as a result of fixed default configurations in hardware. This means that
power may be wasted by these regulators if they are not in use.
Provide intial support for this with a late_initcall which will disable
any unused regulators if the machine has enabled this feature by calling
regulator_has_full_constraints(). If this has not been called then print
a warning to encourage users to fully specify their constraints so that
we can change this to be the default behaviour in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't set use_count for regulators that are enabled at boot since this
stops the supply being disabled by well-behaved consumers which do
balanced enables and disabled. Any consumers which don't do disables
which are not matched by enables are unable to share regulators - shared
regulators are the common case so the API should facilitate them.
Consumers that want to disable regulators that are enabled when they
start have two options:
- Do a regulator_enable() prior to the disable to bring the use count
in sync with the hardware state; this will ensure that if the
regulator was enabled by another driver then this consumer will play
nicely with it.
- Use regulator_force_disable(); this explicitly bypasses any checks
done by the core and documents the inability of the driver to share
the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add VPLL2 to the set of twl4030-family regulators exposed for
use by various drivers. It's commonly used to power the digital
video outputs (e.g. LCD or DVI displays) on OMAP3 systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix some refcounting issues in the regulator framework, supporting
regulator_disable() for regulators that were enabled at boot time
via machine constraints:
- Update those regulators' usecounts after enabling, so they
can cleanly be disabled at that level.
- Remove the problematic per-consumer usecount, so there's
only one level of enable/disable.
Buggy consumers could notice different bug symptoms. The main
example would be refcounting bugs; also, any (out-of-tree) users
of the experimental regulator_set_optimum_mode() stuff which
don't call it when they're done using a regulator.
This is a net minor codeshrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The consumer can print a message if required, some consumers may have
optional regulators and wish to downgrade the logging for them or ignore
their absence.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than incrementing the reference count for boot_on regulators
(which prevents them being disabled later on) simply force the
regulator to be enabled when applying the constraints. Previously
boot_on was essentially equivalent to always_on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
