* git://git.infradead.org/users/cbou/battery-2.6.31:
Add ds2782 battery gas gauge driver
olpc_battery: Ensure that the TRICKLE bit is checked
olpc_battery: Fix up eeprom read function
direct access of driver_data is going away.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are times when the battery is present but trickle charging,
and the EC sets only the TRICKLE bit. So we must check for the bit
when we're checking the charging/present status.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The eeprom read function was placing values into the wrong place in
'buf'; we were starting from buf[off], rather than buf[0].
Also, the for loop that we were using was much uglier than it needed to
be. This cleans it up a bit.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
There are cases when charging monitor and the event handler try to
change the charger state simultaneously. For instance, a charger is
connected to the system, there's the detection event and the event
handler tries to enable charging. It is possible that the periodic
charging monitor runs at the same time and it still thinks there's
no external charger. So it tries to disable the charging. As the
result, even if the conditions necessary to charge the battery hold,
there will be no actual charging.
The patch changes the event handler so that instead of enabling/
disabling the charger immediately it would rather make the monitor
run. The monitor code then decides what should be the charger state.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The MAX17040 is a I2C interfaced Fuel Gauge systems for lithium-ion
batteries This patch adds support the MAX17040 Fuel Gauge
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This adds support for ds2760's sleep mode feature. With this feature
enabled, the chip enters a deep sleep mode and disconnects from the
battery when the w1 line is held down for more than 2 seconds.
This new behaviour can be switched on and off using a new module
parameter.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A few comments say "Celcius"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ACPI has smart batteries, which work in units of energy and measure
rate of (dis)charge as power, thus it is not appropriate to export it
as a current_now. Current_now will still be exported to allow
for userland applications to match.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch allows machines to use an OTG transceiver driver instead of
supplying a custom is_usb_online callback to check USB power.
Also, in the case that the OTG transceiver handles charger control when
connected to USB, a regulator named "ac_draw" can be supplied instead of
the custom set_charge callback to control the charger when connected to
AC.
The check for (transceiver->state == OTG_STATE_B_PERIPHERAL) in
otg_is_usb_online is probably too simple, I'm just using this with a
peripheral only device and gpio_vbus + bq24022. I'm not sure which other
OTG states can supply power.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The battery charger state machine switches into charging mode when
the battery voltage falls below 96% of a battery float voltage. But
the voltage drop in Li-ion batteries is marginal(1~2 %) till about
80% of its capacity - which means, after a BATFULL, charging won't
be restarted until 80%.
This work_struct function restarts charging at regular intervals to
make sure the battery doesn't discharge too much.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
IRQF_DISABLED is not guaranteed for shared IRQs. I think power_changed_isr
doesn't need it anyway, as it only fires a timer.
This patch enables IRQF_SAMPLE_RANDOM instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
