Mika writes:
"thunderbolt: Fix for v6.0 final
This includes a single fix from Mario that resets the plug event delay
back to the USB4 spec value.
This has been in linux-next with no reported issues."
* tag 'thunderbolt-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Explicitly reset plug events delay back to USB4 spec value
Pull USB / Thunderbolt driver fixes and ids from Greg KH:
"Here are a few small USB and Thunderbolt driver fixes and new device
ids for 6.0-rc7.
They contain:
- new usb-serial driver ids
- documentation build warning fix in USB hub code
- flexcop-usb long-posted bugfix (the v4l maintainer for this is MIA
so I have finally picked this up as it is a fix for a reported
problem.)
- dwc3 64bit DMA bugfix
- new thunderbolt device ids
- typec build error fix
All of these have been in linux-next with no reported issues"
* tag 'usb-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: anx7411: Fix build error without CONFIG_POWER_SUPPLY
media: flexcop-usb: fix endpoint type check
USB: serial: option: add Quectel RM520N
USB: serial: option: add Quectel BG95 0x0203 composition
thunderbolt: Add support for Intel Maple Ridge single port controller
usb: dwc3: core: leave default DMA if the controller does not support 64-bit DMA
USB: core: Fix RST error in hub.c
If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.
To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull KUnit fixes from Shuah Khan:
"Two fixes to test build and a fix for incorrect taint reason reporting"
* tag 'linux-kselftest-kunit-fixes-6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
tools: Add new "test" taint to kernel-chktaint
kunit: fix Kconfig for build-in tests USB4 and Nitro Enclaves
kunit: fix assert_type for comparison macros
Add support for Maple Ridge discrete USB4 host controller from Intel
which has a single USB4 port (versus the already supported dual port
Maple Ridge USB4 host controller).
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both the USB4 and Nitro Enclaves KUNIT tests are now able to be compiled
if KUNIT is compiled as a module. This leads to issues if KUNIT is being
packaged separately from the core kernel and when KUNIT is run baremetal
without the required driver compiled into the kernel.
Fixes: 635dcd1684 ("thunderbolt: test: Use kunit_test_suite() macro")
Fixes: fe5be808fa ("nitro_enclaves: test: Use kunit_test_suite() macro")
Signed-off-by: Nico Pache <npache@redhat.com>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Andra Paraschiv <andraprs@amazon.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.
Fixes: 30a4eca69b ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e19 ("thunderbolt: Let the connection manager handle all notifications")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
The new implementation of kunit_test_suite() for modules no longer
conflicts with module_init, so can now be used by the thunderbolt tests.
Also update the Kconfig entry to enable the test when KUNIT_ALL_TESTS is
enabled.
This means that kunit_tool can now successfully run and parse the test
results with, for example:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_PCI=y --kconfig_add CONFIG_USB4=y \
'thunderbolt'
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Use acpi_find_child_by_adr() to find the child matching a given bus
address instead of tb_acpi_find_port() that walks the list of children
of an ACPI device directly for this purpose and drop the latter.
Apart from simplifying the code, this will help to eliminate the
children list head from struct acpi_device as it is redundant and it
is used in questionable ways in some places (in particular, locking is
needed for walking the list pointed to it safely, but it is often
missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Intel Raptor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. By default it is still using firmware based connection
manager so we can use most of the Alder Lake flows.
Signed-off-by: George D Sworo <george.d.sworo@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove some warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/thunderbolt/ctl.c:701: warning: expecting prototype for tb_cfg_start().
Prototype was for tb_ctl_start() instead
drivers/thunderbolt/ctl.c:722: warning: expecting prototype for tb_ctrl_stop().
Prototype was for tb_ctl_stop() instead
drivers/thunderbolt/ctl.c:930: warning: expecting prototype for tb_cfg_write().
Prototype was for tb_cfg_write_raw() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here we configure TMU mode to HiFi uni-directional once DP tunnel
is created. This is due to accuracy requirement for DP tunneling
as appears in CM guide 1.0, section 7.3.2.
Due to Intel hardware limitation, once we changed the TMU mode to HiFi
uni-directional (when DP tunnel exists), we don't change TMU mode back to
normal uni-directional, even if DP tunnel is torn down later.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case of uni-directional time sync, TMU handshake is
initiated by upstream router. In case of bi-directional
time sync, TMU handshake is initiated by downstream router.
In order to handle correctly the case of uni-directional mode,
we avoid changing the upstream router's rate to off,
because it might have another downstream router plugged that is set to
uni-directional mode (and we don't want to change its mode).
Instead, we always change downstream router's rate.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We can't enable CLx if it is not supported either by the host or device,
or by the USB4/TBT link (e.g. when an optical cable is used).
We silently ignore CLx enabling in this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Pull iommu updates from Joerg Roedel:
- Intel VT-d driver updates:
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates:
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU legacy
binding
- Minor cleanups
- Fix a BUG_ON in the vfio_iommu_group_notifier:
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group is
either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Make forcing of cache-coherent DMA more coherent between IOMMU
drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu/amd: Increase timeout waiting for GA log enablement
iommu/s390: Tolerate repeat attach_dev calls
iommu/vt-d: Remove hard coding PGSNP bit in PASID entries
iommu/vt-d: Remove domain_update_iommu_snooping()
iommu/vt-d: Check domain force_snooping against attached devices
iommu/vt-d: Block force-snoop domain attaching if no SC support
iommu/vt-d: Size Page Request Queue to avoid overflow condition
iommu/vt-d: Fold dmar_insert_one_dev_info() into its caller
iommu/vt-d: Change return type of dmar_insert_one_dev_info()
iommu/vt-d: Remove unneeded validity check on dev
iommu/dma: Explicitly sort PCI DMA windows
iommu/dma: Fix iova map result check bug
iommu/mediatek: Fix NULL pointer dereference when printing dev_name
iommu: iommu_group_claim_dma_owner() must always assign a domain
iommu/arm-smmu: Force identity domains for legacy binding
iommu/arm-smmu: Support Tegra234 SMMU
dt-bindings: arm-smmu: Add compatible for Tegra234 SOC
dt-bindings: arm-smmu: Document nvidia,memory-controller property
iommu/arm-smmu-qcom: Add SC8280XP support
dt-bindings: arm-smmu: Add compatible for Qualcomm SC8280XP
...
Add a KUnit test to check that buffer allocation works also for devices
with no DP adapters.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the case of a device without DisplayPort adapters we calculate
incorrectly the amount of buffers. Fix the calculation for this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
