Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
Pull dmaengine updates from Vinod Koul:
"New support / Core:
- Remove DMA_MEMCPY_SG for lack of users
- Tegra 234 dmaengine support
- Mediatek MT8365 dma support
- Apple ADMAC driver
Updates:
- Yaml conversion for ST-Ericsson DMA40 binding and Freescale edma
- rz-dmac updates and device_synchronize support
- Bunch of typo in comments fixes in drivers
- multithread support in sf-pdma driver"
* tag 'dmaengine-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (50 commits)
dmaengine: mediatek: mtk-hsdma: Fix typo 'the the' in comment
dmaengine: axi-dmac: check cache coherency register
dmaengine: sh: rz-dmac: Add device_synchronize callback
dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
dmaengine: tegra: Add terminate() for Tegra234
dt-bindings: dmaengine: Add compatible for Tegra234
dmaengine: xilinx: use strscpy to replace strlcpy
dmaengine: imx-sdma: Add FIFO stride support for multi FIFO script
dmaengine: idxd: Correct IAX operation code names
dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
dmaengine: dw-axi-dmac: do not print NULL LLI during error
dmaengine: altera-msgdma: Fixed some inconsistent function name descriptions
dmaengine: imx-sdma: Add missing struct documentation
dmaengine: sf-pdma: Add multithread support for a DMA channel
dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
dmaengine: dmatest: use strscpy to replace strlcpy
dmaengine: ste_dma40: fix typo in comment
dmaengine: jz4780: fix typo in comment
dmaengine: s3c24xx: fix typo in comment
...
Pull AVR32 updates from Hans-Christian Noren Egtvedt:
"Mostly changes to documentation and comments"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
video:backlight: remove reference to AVR32 architecture in ltv350qv
video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
net: remove cdns,at32ap7000-macb device tree entry
misc: update maintainer email address and description for atmel-ssc
mfd: remove reference to AVR32 architecture in atmel-smc.c
dma:dw: remove reference to AVR32 architecture in core.c
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The AVR32 architecture does no longer exist in the Linux kernel, hence
remove a reference to it in comments to avoid confusion.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Some on-chip peripheral modules(for eg:- rspi) on RZ/G2L SoC
use the same signal for both interrupt and DMA transfer requests.
The signal works as a DMA transfer request signal by setting
DMARS, and subsequent interrupt requests to the interrupt controller
are masked.
We can re-enable the interrupt by clearing the DMARS.
This patch adds device_synchronize callback for clearing
DMARS and thereby allowing DMA consumers to switch to
interrupt mode.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220722084430.969333-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's not allowed to quit remove early without cleaning up completely.
Otherwise this results in resource leaks that probably yield graver
problems later. Here for example some tasklets might survive the lifetime
of the sprd-dma device and access sdev which is freed after .remove()
returns.
As none of the device freeing requires an active device, just ignore the
return value of pm_runtime_get_sync().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20220721204054.323602-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In certain cases where the DMA client bus gets corrupted or if the
end device ceases to send/receive data, DMA can wait indefinitely
for the data to be received/sent. Attempting to terminate the transfer
will put the DMA in pause flush mode and it remains there.
The channel is irrecoverable once this pause times out in Tegra194 and
earlier chips. Whereas, from Tegra234, it can be recovered by disabling
the channel and reprograming it.
Hence add a new terminate() function that ignores the outcome of
dma_pause() so that terminate_all() can proceed to disable the channel.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220720104045.16099-3-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The peripheral may have several FIFOs, but some case just select
some FIFOs from them for data transfer, which means FIFO0 and FIFO2
may be selected. So add FIFO address stride support, 0 means all FIFOs
are continuous, 1 means 1 word stride between FIFOs. All stride between
FIFOs should be same.
Another option words_per_fifo means how many audio channel data copied
to one FIFO one time, 1 means one channel per FIFO, 2 means 2 channels
per FIFO.
If 'n_fifos_src = 4' and 'words_per_fifo = 2', it means the first two
words(channels) fetch from FIFO0 and then jump to FIFO1 for next two words,
and so on after the last FIFO3 fetched, roll back to FIFO0.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1657162829-9273-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Inconsistent function names describing msgdma_chan_remove() and
msgdma_dma_remove are modified to msgdma_dev_remove() and msgdma_remove().
Remove some warnings found by running scripts/kernel-doc, which is caused
by using 'make W=1'.
drivers/dma/altera-msgdma.c:927: warning: expecting prototype for msgdma_dma_remove(). Prototype was for msgdma_remove() instead.
drivers/dma/altera-msgdma.c:758: warning: expecting prototype for msgdma_chan_remove(). Prototype was for msgdma_dev_remove() instead.
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/20220706082605.114907-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When we get a DMA channel and try to use it in multiple threads it
will cause oops and hanging the system.
% echo 64 > /sys/module/dmatest/parameters/threads_per_chan
% echo 10000 > /sys/module/dmatest/parameters/iterations
% echo 1 > /sys/module/dmatest/parameters/run
[ 89.480664] Unable to handle kernel NULL pointer dereference at virtual
address 00000000000000a0
[ 89.488725] Oops [#1]
[ 89.494708] CPU: 2 PID: 1008 Comm: dma0chan0-copy0 Not tainted
5.17.0-rc5
[ 89.509385] epc : vchan_find_desc+0x32/0x46
[ 89.513553] ra : sf_pdma_tx_status+0xca/0xd6
This happens because of data race. Each thread rewrite channels's
descriptor as soon as device_prep_dma_memcpy() is called. It leads to the
situation when the driver thinks that it uses right descriptor that
actually is freed or substituted for other one.
With current fixes a descriptor changes its value only when it has
been used. A new descriptor is acquired from vc->desc_issued queue that
is already filled with descriptors that are ready to be sent. Threads
have no direct access to DMA channel descriptor. Now it is just possible
to queue a descriptor for further processing.
Fixes: 6973886ad5 ("dmaengine: sf-pdma: add platform DMA support for HiFive Unleashed A00")
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Link: https://lore.kernel.org/r/20220701082942.12835-1-v.v.mitrofanov@yadro.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
