Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a big revert of a lot of -rc1 tidspbridge patches in order to
get the driver back into a working state. It also includes a OMAP patch
that was approved by the OMAP maintainer.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On 2.6.37-rc1, omap platform internals for SCM have changed,
so the build is broken again.
drivers/staging/tidspbridge/core/tiomap3430.c:26:
fatal error: plat/control.h: No such file or directory
This is a totally ugly layer violation, but needed until
omap_ctrl_set_dsp_boot*() are provided.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
There was commented out transfer_flags initialization.
And i think memset should fill entire structure, not only length of
pointer to it.
This makes the driver work properly now on my hardware.
Signed-off-by: Konstantin Katuev <kkatuev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes bug #13820 from bugzilla.kernel.org.
Quote: "If ETHTOOL_GLINK is not defined, the end for switch case is not
to be found."
Signed-off-by: Maximiliano David Bustos <md.bustos90@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit e31b82136d ("cfg80211/mac80211:
allow per-station GTKs") changed the signatures of these operations
but did not update the staging drivers.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unnecessary cast of firmware base address to integer before
adding an offset.
Fix direct use of sk_buff::network_header which is an offset rather
than a pointer on 64-bit architectures.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Whenever the mac address of an batman interface is changed
check_known_mac_addr() is called to print a warning if the newly added
mac address exists an another batman interface. While looping through
the batman interface list check_known_mac_addr() only compares mac
addresses and does not make sure they belong to different interfaces,
thus always printing a warning.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
55d1666b521cbed95924c8d4775fe272c103f08c incidentally disabled bonding
of packets first entering the mesh along with also disabling interface
alternating regardless of where the packet came from. This re-enables
these options.
Signed-off-by: Chris Lang <clang@gateworks.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unmap the rx buffer before mapping the new one in rtl8192_rx.
Failing to do so quickly exhausts the IOMMU memory during downloads:
[...] DMA: Out of SW-IOMMU space for 9100 bytes at device ...
Using "iommu=off mem=4g" also fixes the problem because
then pci_map_single does not allocate memory.
Tested on my personal laptop with a RTL8192E device. Without this
patch the kernel quickly runs out of IOMMU memory (downloading 5 MB
of data is sufficient to trigger it), with this patch applied
I haven't experienced any issues so far.
Signed-off-by: Daniel Lichtenberger <daniel.lichtenberger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>