* git://git.infradead.org/mtd-2.6: (82 commits)
mtd: fix build error in m25p80.c
mtd: Remove redundant mutex from mtd_blkdevs.c
MTD: Fix wrong check register_blkdev return value
Revert "mtd: cleanup Kconfig dependencies"
mtd: cfi_cmdset_0002: make sector erase command variable
mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips
mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode
mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one
block2mtd: dubious assignment
P4080/mtd: Fix the freescale lbc issue with 36bit mode
P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
mtd: phram: use KBUILD_MODNAME
mtd: OneNAND: S5PC110: Fix double call suspend & resume function
mtd: nand: fix MTD_MODE_RAW writes
jffs2: use kmemdup
mtd: sm_ftl: cosmetic, use bool when possible
mtd: r852: remove useless pci powerup/down from suspend/resume routines
mtd: blktrans: fix a race vs kthread_stop
mtd: blktrans: kill BKL
mtd: allow to unload the mtdtrans module if its block devices aren't open
...
Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
Conflicts:
drivers/mtd/mtd_blkdevs.c
Merge Grant's device-tree bits so that we can apply the subsequent fixes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The TASK_SIZE macro should reflect the size of a user process virtual
address space. Previously for 64-bit kernels, this was not the case.
The immediate cause of pain was in
hugetlbfs/inode.c:hugetlb_get_unmapped_area() where 32-bit processes
trying to mmap a huge page would be served a page with an address
outside of the 32-bit address range. But there are other uses of
TASK_SIZE in the kernel as well that would like an accurate value.
The new definition is nice because it now makes TASK_SIZE and
TASK_SIZE_OF() yield the same value for any given process.
For 32-bit kernels there should be no change, although I did factor
out some code in asm/processor.h that became identical for the 32-bit and
64-bit cases.
__UA_LIMIT is now set to ~((1 << SEGBITS) - 1) for 64-bit kernels.
This should eliminate the possibility of getting a
AddressErrorException in the kernel for addresses that pass the
access_ok() test.
With the patch applied, I can still run o32, n32 and n64 processes,
and have an o32 shell fork/exec both n32 and n64 processes.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1701/
BMIPS processor cores are used in 50+ different chipsets spread across
5+ product lines. In many cases the chipsets do not share the same
peripheral register layouts, the same register blocks, the same
interrupt controllers, the same memory maps, or much of anything else.
But, across radically different SoCs that share nothing more than the
same BMIPS CPU, a few things are still mostly constant:
SMP operations
Access to performance counters
DMA cache coherency quirks
Cache and memory bus configuration
So, it makes sense to treat each BMIPS processor type as a generic
"building block," rather than tying it to a specific SoC. This makes it
easier to support a large number of BMIPS-based chipsets without
unnecessary duplication of code, and provides the infrastructure needed
to support BMIPS-proprietary features.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Florian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
This patch provides the skeleton of the HW perf event support. To enable
this feature, we can not choose the SMTC kernel; Oprofile should be
disabled; kernel performance events be selected. Then we can enable it in
Kernel type menu.
Oprofile for MIPS platforms initializes irq at arch init time. Currently
we do not change this logic to allow PMU reservation.
If a platform has EIC, we can use the irq base and perf counter irq offset
defines for the interrupt controller in specific init_hw_perf_events().
Based on this skeleton patch, the 3 different kinds of MIPS PMU, namely,
mipsxx/loongson2/rm9000, can be supported by adding corresponding lower
level C files at the bottom. The suggested names of these files are
perf_event_mipsxx.c/perf_event_loongson2.c/perf_event_rm9000.c. So, for
example, we can do this by adding "#include perf_event_mipsxx.c" at the
bottom of perf_event.c.
In addition, PMUs with 64bit counters are also considered in this patch.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1688/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for Titan TNETV1050,1055,1056,1060 variants. This SoC is almost
completely identical to AR7 except on a few points:
- a second bank of gpios is available
- vlynq0 on titan is vlynq1 on ar7
- different PHY addresses for cpmac0
This SoC can be found on commercial products like the Linksys WRTP54G
Original patch by Xin with improvments by Florian.
Signed-off-by: Xin Zhen <xlonestar2000@aim.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1563/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Starting with cn63xx Octeon I/O blocks are clocked at a different rate
than the CPU. Add a new function octeon_get_io_clock_rate() that
yields the I/O clock rate.
Also rearrange octeon_get_clock_rate() to get the value from the saved
sysinfo structure.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1671/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CN63XX has a different L2 cache architecture. Update the helper
functions to reflect this.
Some joining of split lines was also done to improve readability, as
well as reformatting of comments.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CN63XX is a new 6-CPU SOC based on the new OCTEON II CPU cores.
Join some lines back together. This makes some of them exceed 80
columns, but they are uninteresting and this unclutters things.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Octeon chips can support more than 4GB of RAM. Also due to how Octeon
PCI is setup, even some configurations with less than 4GB of RAM will have
portions that are not accessible from 32-bit devices.
Enable the swiotlb code to handle the cases where a device cannot directly
do DMA. This is a complete rewrite of the Octeon DMA mapping code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use asm-generic/dma-mapping-common.h to handle all DMA mapping operations
and establish a default get_dma_ops() that forwards all operations to the
existing code.
Augment dev_archdata to carry a pointer to the struct dma_map_ops, allowing
DMA operations to be overridden on a per device basis. Currently this is
never filled in, so the default dma_map_ops are used. A follow-on patch
sets this for Octeon PCI devices.
Also initialize the dma_debug system as it is now used if it is configured.
Includes fixes by Kevin Cernekee <cernekee@gmail.com>.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1637/
Patchwork: http://patchwork.linux-mips.org/patch/1678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was a nice optimization - on paper at least. In practice it results in
branches that may exceed the maximum legal range for a branch. We can
fight that problem with -ffunction-sections but -ffunction-sections again
is incompatible with -pg used by the function tracer.
By rewriting the loop around all simple LL/SC blocks to C we reduce the
amount of inline assembler and at the same time allow GCC to often fill
the branch delay slots with something sensible or whatever else clever
optimization it may have up in its sleeve.
With this optimization gone we also no longer need -ffunction-sections,
so drop it.
This optimization was originally introduced in 2.6.21, commit
5999eca25c1fd4b9b9aca7833b04d10fe4bc877d (linux-mips.org) rsp.
f65e4fa8e0 (kernel.org).
Original fix for the issues which caused me to pull this optimization by
Paul Gortmaker <paul.gortmaker@windriver.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dma64_addr_t looks pointless (at least there is no point that an
architecture has the own dma64_addr_t typedef).
dma_addr_t is set to 32 or 64 bits appropriately. You can use u64 at
places where you know that 64 bit address is always necessary.
Let's use u64 instead for mips.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
David Woodhouse
David Daney
Kevin Cernekee
Deng-Cheng Zhu
Florian Fainelli
From: jiang.adam@gmail.com
Ralf Baechle
FUJITA Tomonori