When an NFC driver or host controller stack discovers a secure element,
it will call nfc_add_se(). In order for userspace applications to use
these secure elements, a netlink event will then be sent with the SE
index and its type. With that information userspace applications can
decide wether or not to enable SEs, through their indexes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add netlink directives and ndo entry to allow for controling
VF link, which can be in one of three states:
Auto - VF link state reflects the PF link state (default)
Up - VF link state is up, traffic from VF to VF works even if
the actual PF link is down
Down - VF link state is down, no traffic from/to this VF, can be of
use while configuring the VF
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TUN_PERSIST flag is not reported at all -- both TUNGETIFF, and sysfs
"flags" attribute skip one. Knowing whether a device is persistent or not
is critical for checkpoint-restore, thus I propose to add the read-only
IFF_PERSIST one for this.
Setting this new IFF_PERSIST is hardly possible, as TUNSETIFF doesn't check
for unknown flags being zero and thus there can be trash.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire the init of a 32bit vcpu by allowing 32bit modes in pstate,
and providing sensible defaults out of reset state.
This feature is of course conditioned by the presence of 32bit
capability on the physical CPU, and is checked by the KVM_CAP_ARM_EL1_32BIT
capability.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
struct gnet_stats_rate_est contains u32 fields, so the bytes per second
field can wrap at 34360Mbit.
Add a new gnet_stats_rate_est64 structure to get 64bit bps/pps fields,
and switch the kernel to use this structure natively.
This structure is dumped to user space as a new attribute :
TCA_STATS_RATE_EST64
Old tc command will now display the capped bps (to 34360Mbit), instead
of wrapped values, and updated tc command will display correct
information.
Old tc command output, after patch :
eric:~# tc -s -d qd sh dev lo
qdisc pfifo 8001: root refcnt 2 limit 1000p
Sent 80868245400 bytes 1978837 pkt (dropped 0, overlimits 0 requeues 0)
rate 34360Mbit 189696pps backlog 0b 0p requeues 0
This patch carefully reorganizes "struct Qdisc" layout to get optimal
performance on SMP.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use 0x7000000000000000ULL as 0x6000000000000000ULL is reserved for
ARM64.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Freescale lpuart driver support. The lpuart device
can be found on Vybrid VF610 and Layerscape LS-1 SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host ping its peer, ICMP echo request packet triggers IPsec
policy, then host negotiates SA secret with its peer. After IKE
installed SA for OUT direction, but before SA for IN direction
installed, host get ICMP echo reply from its peer. At the time
being, the SA state for IN direction could be XFRM_STATE_ACQ,
then the received packet will be dropped after adding
LINUX_MIB_XFRMINSTATEINVALID statistic.
Adding a LINUX_MIB_XFRMACQUIREERROR statistic counter for such
scenario when SA in larval state is much clearer for user than
LINUX_MIB_XFRMINSTATEINVALID which indicates the SA is totally
bad.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a comment which explains the real meaning of XCVR_INTERNAL (PHY and
Ethernet MAC in the same package/die) and XCVR_EXTERNAL (PHY and
Ethernet MAC in a different package/die). Most if not all of the drivers
setting their transceiver type already do it the way the comment
describes it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Samuel Ortiz
Rony Efraim
Eric Lapuyade
Pavel Emelyanov
Marc Zyngier
John W. Linville
Colleen Twitty
Felix Fietkau
Eric Dumazet
Vlad Yasevich
David Daney
Eliezer Tamir
Jingchang Lu
Fan Du
Yijing Wang
Florian Fainelli
Lad, Prabhakar
Jouni Malinen
Ismael Luceno
Pranavkumar Sawargaonkar