Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
Now struct spi_master is used for both SPI master and slave controllers,
it makes sense to rename it to struct spi_controller, and replace
"master" by "controller" where appropriate.
For now this conversion is done for SPI core infrastructure only.
Wrappers are provided for backwards compatibility, until all SPI drivers
have been converted.
Noteworthy details:
- SPI_MASTER_GPIO_SS is retained, as it only makes sense for SPI
master controllers,
- spi_busnum_to_master() is retained, as it looks up masters only,
- A new field spi_device.controller is added, but spi_device.master is
retained for compatibility (both are always initialized by
spi_alloc_device()),
- spi_flash_read() is used by SPI masters only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add slave mode support to the MSIOF driver, in both PIO and DMA mode.
For now this only supports the transmission of messages with a size
that is known in advance.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Timeout handling cleanup, spi core integration, cancellation,
rewording]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for registering SPI slave controllers using the existing SPI
master framework:
- SPI slave controllers must use spi_alloc_slave() instead of
spi_alloc_master(), and should provide an additional callback
"slave_abort" to abort an ongoing SPI transfer request,
- SPI slave controllers are added to a new "spi_slave" device class,
- SPI slave handlers can be bound to the SPI slave device represented
by an SPI slave controller using a DT child node named "slave",
- Alternatively, (un)binding an SPI slave handler to the SPI slave
device represented by an SPI slave controller can be done by
(un)registering the slave device through a sysfs virtual file named
"slave".
From the point of view of an SPI slave protocol handler, an SPI slave
controller looks almost like an ordinary SPI master controller. The only
exception is that a transfer request will block on the remote SPI
master, and may be cancelled using spi_slave_abort().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment does not match the driver, which actually supports
automatic assignment. Fix this by updating the comment.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.
As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23s08 support configuration of the pullups using the
pinconf framework. This removes the custom pullup configuration
from platform data, which has no upstream users.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add an interface analogous to ->can_dma() for spi_flash_read()
interface. This will enable SPI controller drivers to inform SPI core
when not to do DMA mappings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Invoke the proper function while initializing
a dynamically allocated spi_message to avoid
NULL pointer dereference during resources deallocation.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic device properties support statically defined property sets. For
them to be usable, we need to attach these property sets before devices
are registered and probed. Allowing to attach property list to
spi_board_info structure will allow non-ACPI non-DT boards switch to using
generic properties and get rid of custom platform data.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of supporting legacy platform data (of which we have no mainline
users) and OF-based properties, let's switch to generic device properties.
This will still allow legacy boards to use the driver (by defining property
sets and attaching them to the drivers) and will simplify probe and make
driver usable on ACPI-based systems as well.
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some SPI masters require slave selection before the transfer
can begin [1]. The SPI framework currently selects the chip using
either 1) the internal CS mechanism or 2) the GPIO CS, but not both.
This patch adds a new master->flags define to indicate both the GPIO
CS and the internal chip select mechanism should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify spi_write() and spi_read() using the spi_sync_transfer()
helper.
This requires moving spi_sync_transfer() up.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently a maximum transfer size was was introduced in struct spi_master.
However there are also spi controllers with a maximum message size, e.g.
fsl-espi has a max message size of 64KB.
Introduce a hook max_message_size to deal with such limitations.
Also make sure that spi_max_transfer_size doesn't return greater values
than spi_max_message_size, even if hook max_transfer_size is not set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current SPI code attempts to use bus_lock_mutex for two purposes. One
is to implement spi_bus_lock() which grants exclusive access to the bus.
The other is to serialize access to the physical hardware. This duplicate
purpose causes confusion which leads to cases where access is not locked
when a caller holds the bus lock mutex. Fix this by splitting out the I/O
functionality into a new io_mutex.
This means taking both mutexes in the DMA path, replacing the existing
mutex with the new I/O one in the message pump (the mutex now always
being taken in the message pump) and taking the bus lock mutex in
spi_sync(), allowing __spi_sync() to have no mutex handling.
While we're at it hoist the mutex further up the message pump before we
power up the device so that all power up/down of the block is covered by
it and there are no races with in-line pumping of messages.
Reported-by: Rich Felker <dalias@libc.org>
Tested-by: Rich Felker <dalias@libc.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Few SPI devices provide accelerated read interfaces to read from
SPI-NOR flash devices. These hardwares also support DMA to transfer data
from flash to memory either via mem-to-mem DMA or dedicated slave DMA
channels. Hence, add support for DMA in order to improve throughput and
reduce CPU load.
Use spi_map_buf() to get sg table for the buffer and pass it to SPI
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If hook spi_flash_read is implemented the fast flash read feature
is enabled for all devices attached to the respective master.
In most cases there is just one flash chip, however there are also
devices with more than one flash chip, namely some WiFi routers.
Then the fast flash read feature can be used for the first chip only.
OpenWRT implemented an own handling of this case, using controller_data
element of spi_device to hold the information whether fast flash read
can be used for a device.
This patch adds hook flash_read_supported to spi_master which is
used to extend spi_flash_read_supported() by checking whether the
fast flash read feature can be used for a specific spi_device.
If the hook is not implemented the default behavior is to allow
fast flash read for all devices (if spi_flash_read is implemented).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
