Some overlapping changes in the mlx5 driver.
A merge conflict resolution posted by Stephen Rothwell was used as a
guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add routines for manipulating the hardware IPSec SA database (SADB).
In Innova IPSec, a Security Association (SA) is added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova IPSec (FPGA-based) hardware.
These routines will be used by the IPSec offload support in a later patch
However they may also be used by others such as RDMA and RoCE IPSec.
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In this patchset we add Innova IPSec support and mlx5/accel delegates
IPSec offloads to Innova routines.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The Innova FPGA includes shell hardware and Sandbox-Unit (SBU) hardware.
The shell hardware is handled by mlx5_core itself, while the SBU is
handled by a client driver.
Reset the SBU to a well-known initial state when initializing a new
device, and set the FPGA to bypass mode when uninitializing a device.
This allows the client driver to assume that its device has been
reset when a new device is detected.
During SBU reset, the FPGA is put into SBU-bypass mode. In this mode
packets do not pass through the SBU, so it cannot affect the network
data stream at all.
A factory-image does not have an SBU, so skip these flows.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reserved GIDs are entries in the GID table in use by the mlx5_core
and its submodules (e.g. FPGA, SRIOV, E-Swtich, netdev).
The entries are reserved at the high indexes of the GID table.
A mlx5 submodule may reserve a certain amount of GIDs for its own use
during the load sequence by calling mlx5_core_reserve_gids, and must
also take care to un-reserve these GIDs when it closes.
Reservation is only allowed during the load sequence and before any
interfaces (e.g. mlx5_ib or mlx5_en) are up.
After reservation, a submodule may call mlx5_core_reserved_gid_alloc/
free to allocate entries from the reserved GIDs pool.
Reserve a GID table entry for every supported FPGA QP.
A later patch in the patchset will remove them from being reported to
IB core.
Another such patch will make use of these for FPGA QPs in Innova NIC.
Added lib/mlx5.h to serve as a library for mlx5 submodlues, and to
expose only public mlx5 API, more mlx5 library files will be added in
future submissions.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.
Fixes: 5e44fca504 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The offending commit pushed fwd the field by two bits but
didn't increment the offset, fix that. Currently, no damage
was done b/c this is just a field name, but lets have it right.
Fixes: f32f5bd2eb ('net/mlx5: Configure cache line size for start and end padding')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enable offloading of TC matching on ip ttl / hop-limit
As matching on ttl is supported only by newer HW brands (ConnectX-5),
we should do capability check before attempting to offload that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding a support to flush all HW resources with one FW command and
skip all the heavy unload flows of the driver on kernel shutdown.
There's no need to free all the SW context since a new fresh kernel
will be loaded afterwards.
Regarding the FW resources, they should be closed, otherwise we will
have leakage in the FW. To accelerate this flow, we execute one command
in the beginning that tells the FW that the driver isn't going to close
any of the FW resources and asks the FW to clean up everything.
Once the commands complete, it's safe to close the PCI resources and
finish the routine.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a new interface for commands execution that allows the
caller to wait for the command's completion in a busy-wait
loop (polling mode).
This is useful if we want to execute a command in a polling mode
while the driver is working in events mode for the rest of
the commands.
This interface will be used in the downstream patches.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move "query queue counter out of buffer" helper function out of
qp.c to en_main.c, since mlx5e netdev driver is the only one to use it.
Also allocate the output buffer on the stack instead of the heap, to reduce
number of heap allocs on update_stats work.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Fixed few places where endianness was misspelled and
one spot whwere output was:
CHECK: 'endianess' may be misspelled - perhaps 'endianness'?
CHECK: 'ouput' may be misspelled - perhaps 'output'?
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read port connector type from the firmware instead of caching it in the
driver metadata.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update struct mlx5_ifc_create(modify)_flow_table_bits according to
the last device specification.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
HW can implement UMR wqe re-transmission in various ways.
Thus, add HCA cap to distinguish the needed fence for UMR to make
sure that the wqe wouldn't fail on mkey checks.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-update-2017-05-23
First patch from Leon, came to remove the redundant usage of mlx5_vzalloc,
and directly use kvzalloc across all mlx5 drivers.
2nd patch from Noa, adds new device IDs into the supported devices list.
3rd and 4th patches from Ilan are adding the basic infrastructure and
support for Mellanox's mlx5 FPGA.
Last two patches from Tariq came to modify the outdated driver version
reported in ethtool and in mlx5_ib to more reflect the current driver state
and remove the redundant date string reported in the version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-fixes-2017-05-23
Some TC offloads fixes from Or Gerlitz.
From Erez, mlx5 IPoIB RX fix to improve GRO.
From Mohamad, Command interface fix to improve mitigation against FW
commands timeouts.
From Tariq, Driver load Tolerance against affinity settings failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
