Certain keyboards have their top-row keys intended for actions such as
"Browser back", "Browser Refresh", "Fullscreen" etc as their primary mode,
thus they will send scan codes for those actions. Further, they don't
have a dedicated "Fn" key so don't have the capability to generate
function key codes (e.g. F1, F2 etc..). However in this case, if
userspace still wants to "synthesize" those function keys using the top
row action keys, it needs to know the physical position of the top row
keys. (Essentially a mapping between usage codes and a physical location
in the top row).
This patch enhances the atkbd driver to receive such a mapping from the
firmware / device tree, and expose it to userspace in the form of a
function-row-physmap attribute. The attribute would be a space separated
ordered list of physical codes, for the keys in the function row, in
left-to-right order.
The attribute will only be present if the kernel knows about such mapping,
otherwise the attribute shall not be visible.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-2-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS345L is another first generation touch screen from Melfas,
which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization.
Apparently MMS345L does not have the MMS152_COMPAT_GROUP register
that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as
an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading
from the MMS152_COMPAT_GROUP register. This might also help in case
there is some other device-specific quirk in the future.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200423102431.2715-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some processes, such as systemd, are only polling for EPOLLERR|EPOLLHUP.
As evdev uses unkeyed wakeups, such a poll receives many spurious
wakeups from uninteresting events.
Use keyed wakeups to allow the wakeup target to more efficiently discard
these uninteresting events.
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://lore.kernel.org/r/20200410233557.3892-1-kl@kl.wtf
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Acer Aspire 5738z has a button to disable (and re-enable) the
touchpad next to the touchpad.
When this button is pressed a LED underneath indicates that the touchpad
is disabled (and an event is send to userspace and GNOME shows its
touchpad enabled / disable OSD thingie).
So far so good, but after re-enabling the touchpad it no longer works.
The laptop does not have an external ps2 port, so mux mode is not needed
and disabling mux mode fixes the touchpad no longer working after toggling
it off and back on again, so lets add this laptop model to the nomux list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200331123947.318908-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
acpi_evaluate_object() and acpi_execute_simple_method() are not part of
the group of ACPI related functions which get stubbed by
include/linux/acpi.h when ACPI support is disabled, so the
IRQ_PIN_ACCESS_ACPI_METHOD handling code must be stubbed out.
For consistency use the same #if condition as which is used to replace
goodix_add_acpi_gpio_mappings with a stub.
Fixes: c5fca48532 ("Input: goodix - add support for controlling the IRQ pin through ACPI methods")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200401014529.GL75430@dtor-ws
[dtor: stubbed out the ACPI method accessors]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Marco Felsch
Rajat Jain
Stephan Gerhold
Linus Walleij
Kenny Levinsen
Christophe JAILLET
Hans de Goede
Andy Shevchenko
Yannick Fertre
Icenowy Zheng
Dmitry Mastykin