There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Currently ocelot_set_rx_mode calls ocelot_mact_learn directly, which has
a very nice ocelot_mact_wait_for_completion at the end. Introduced in
commit 639c1b2625 ("net: mscc: ocelot: Register poll timeout should be
wall time not attempts"), this function uses readx_poll_timeout which
triggers a lot of lockdep warnings and is also dangerous to use from
atomic context, potentially leading to lockups and panics.
Steen Hegelund added a poll timeout of 100 ms for checking the MAC
table, a duration which is clearly absurd to poll in atomic context.
So we need to defer the MAC table access to process context, which we do
via a dynamically allocated workqueue which contains all there is to
know about the MAC table operation it has to do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212191612.222019-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.
So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.
The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.
And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
MC6_DATA = 61,
MC6_CTRL = 61,
MC4_DATA = 60,
MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.
Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multiple Tegra drivers need to retrieve Memory Controller and there is
duplication of the retrieval code among the drivers.
Add new devm_tegra_memory_controller_get() helper to remove the code's
duplication and to fix put_device() which was missed in the duplicated
code. Make EMC drivers to use the new helper.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-29-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we are checking in some places whether the port has a native
VLAN on egress or not, by comparing the ocelot_port->vid value with zero.
That works, because VID 0 can never be a native VLAN configured by the
bridge, but now we want to make similar checks for the pvid. That won't
work, because there are cases when we do have the pvid set to 0 (not by
the bridge, by ourselves, but still.. it's confusing). And we can't
encode a negative value into an u16, so add a bool to the structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is one main difference in mscc_ocelot between IP multicast and L2
multicast. With IP multicast, destination ports are encoded into the
upper bytes of the multicast MAC address. Example: to deliver the
address 01:00:5E:11:22:33 to ports 3, 8, and 9, one would need to
program the address of 00:03:08:11:22:33 into hardware. Whereas for L2
multicast, the MAC table entry points to a Port Group ID (PGID), and
that PGID contains the port mask that the packet will be forwarded to.
As to why it is this way, no clue. My guess is that not all port
combinations can be supported simultaneously with the limited number of
PGIDs, and this was somehow an issue for IP multicast but not for L2
multicast. Anyway.
Prior to this change, the raw L2 multicast code was bogus, due to the
fact that there wasn't really any way to test it using the bridge code.
There were 2 issues:
- A multicast PGID was allocated for each MDB entry, but it wasn't in
fact programmed to hardware. It was dummy.
- In fact we don't want to reserve a multicast PGID for every single MDB
entry. That would be odd because we can only have ~60 PGIDs, but
thousands of MDB entries. So instead, we want to reserve a multicast
PGID for every single port combination for multicast traffic. And
since we can have 2 (or more) MDB entries delivered to the same port
group (and therefore PGID), we need to reference-count the PGIDs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP/FSL SoC driver updates for v5.10
Fix various compile warnings and static analysis warnings for:
- QBMan driver
- DPIO driver
- QE driver
* tag 'soc-fsl-next-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
soc: fsl: dpio: remove set but not used 'addr_cena'
soc: fsl: qbman: Fix return value on success
soc: fsl: qman: fix -Wpacked-not-aligned warnings
Link: https://lore.kernel.org/r/20200923224416.25788-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean
Vineet Gupta
Linus Torvalds
Jakub Kicinski
Dmitry Osipenko
Sebastian Andrzej Siewior
David S. Miller
Greg Kroah-Hartman
Olof Johansson