For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.
Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.
Thanks to Damien Le Moal for some good suggestion.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
Since bdced438ac ("block: setup bi_phys_segments after splitting"),
physical segment number is mainly figured out in blk_queue_split() for
fast path, and the flag of BIO_SEG_VALID is set there too.
Now only blk_recount_segments() and blk_recalc_rq_segments() use this
flag.
Basically blk_recount_segments() is bypassed in fast path given BIO_SEG_VALID
is set in blk_queue_split().
For another user of blk_recalc_rq_segments():
- run in partial completion branch of blk_update_request, which is an unusual case
- run in blk_cloned_rq_check_limits(), still not a big problem if the flag is killed
since dm-rq is the only user.
Multi-page bvec is enabled now, not doing S/G merging is rather pointless with the
current setup of the I/O path, as it isn't going to save you a significant amount
of cycles.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_for_each_bvec() is used for iterating over multi-page bvec for bio
split & merge code.
rq_for_each_bvec() can be used for drivers which may handle the
multi-page bvec directly, so far loop is one perfect use case.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have QUEUE_FLAG_DEFAULT defined, but it's not used anymore since
the legacy IO stack is gone. Kill it.
Sanitize the queue flags in general, they use spaces (for some
reason), and the space is pretty sparse. With the flags renumbered,
we can more clearly see how many we have available.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have various helpers for setting/clearing this flag, and also
a helper to check if the queue supports queueable flushes or not.
But nobody uses them anymore, kill it with fire.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Unused now, and another field in struct request bites the dust.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Now that the the SCSI layer replaced the use of the cluster flag with
segment size limits and the DMA boundary we can remove the cluster flag
from the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk-mq-debugfs has been proved as very helpful for debug some
tough issues, such as IO hang.
We have seen blk-wbt related IO hang several times, even inside
Red Hat BZ, there is such report not sovled yet, so this patch
adds support debugfs on rq_qos.
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only support polling if we have poll queues now, but the flag is
being set by default. Remove the default QUEUE_FLAG_POLL setting, we'll
set it in blk_mq_init_allocated_queue() if we have poll queues available
for this device.
Fixes: 6544d229bf ("block: enable polling by default if a poll map is initalized")
Reported-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This was intended to support users like nvme multipath, but is just
getting in the way and adding another indirect call.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only do it if we have requests for multiple queues in the same
plug.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This isn't exactly the same as the previous count, as it includes
requests for all devices. But that really doesn't matter, if we have
more than the threshold (16) queued up, flush it. It's not worth it
to have an expensive list loop for this.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_poll() has always kept spinning until it found an IO. This is
fine for SYNC polling, since we need to find one request we have
pending, but in preparation for ASYNC polling it can be beneficial
to just check if we have any entries available or not.
Existing callers are converted to pass in 'spin == true', to retain
the old behavior.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we want to support async IO polling, then we have to allow finding
completions that aren't just for the one we are looking for. Always pass
in -1 to the mq_ops->poll() helper, and have that return how many events
were found in this poll loop.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Even though .mq_kobj, ctx->kobj and q->kobj share same lifetime
from block layer's view, actually they don't because userspace may
grab one kobject anytime via sysfs.
This patch fixes the issue by the following approach:
1) introduce 'struct blk_mq_ctxs' for holding .mq_kobj and managing
all ctxs
2) free all allocated ctxs and the 'blk_mq_ctxs' instance in release
handler of .mq_kobj
3) grab one ref of .mq_kobj before initializing each ctx->kobj, so that
.mq_kobj is always released after all ctxs are freed.
This patch fixes kernel panic issue during booting when DEBUG_KOBJECT_RELEASE
is enabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently only really support sync poll, ie poll with 1 IO in flight.
This prepares us for supporting async poll.
Note that the returned value isn't necessarily 100% accurate. If poll
races with IRQ completion, we assume that the fact that the task is now
runnable means we found at least one entry. In reality it could be more
than 1, or not even 1. This is fine, the caller will just need to take
this into account.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we're polling for IO on a device that doesn't use interrupts, then
IO completion loop (and wake of task) is done by submitting task itself.
If that is the case, then we don't need to enter the wake_up_process()
function, we can simply mark ourselves as TASK_RUNNING.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Various spots check for q->mq_ops being non-NULL, but provide
a helper to do this instead.
Where the ->mq_ops != NULL check is redundant, remove it.
Since mq == rq-based now that legacy is gone, get rid of the
queue_is_rq_based() and just use queue_is_mq() everywhere.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the legacy request path gone there is no good reason to keep
queue_lock as a pointer, we can always use the embedded lock now.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixed floppy and blk-cgroup missing conversions and half done edits.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the legacy request path gone there is no real need to override the
queue_lock.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
->queue_flags is generally not set or cleared in the fast path, and also
generally set or cleared one flag at a time. Make use of the normal
atomic bitops for it so that we don't need to take the queue_lock,
which is otherwise mostly unused in the core block layer now.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
