Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Pull rockchip clk driver updates from Heiko Stuebner:
A new clock controller for the rk1108 soc (single-core Cortex-A7+DSP),
a fix making sure the cpuclk rate is actually valid, before trying to
set it and a copy-paste fix for the rk3399's testclk.
* tag 'v4.10-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add clock controller for rk1108
dt-bindings: add documentation for rk1108 cru
clk: rockchip: add dt-binding header for rk1108
clk: rockchip: fix copy-paste error in rk3399 testclk
clk: rockchip: validity should be checked prior to cpu clock rate change
Pull "Rockchip dts32 changes for 4.10" from Heiko Stübner:
A bit of attention for the rk3066, fixed tsadc reset node
as well as enabling the dma for uart and mmc controllers.
And one new soc, the rk1108 combining a single-core Cortex-A7
with a separate DSP core.
* tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the sdmmc pinctrl for rk1108
ARM: dts: rockchip: add rockchip RK1108 Evaluation board
ARM: dts: rockchip: add basic support for RK1108 SOC
clk: rockchip: add dt-binding header for rk1108
dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
ARM: dts: rockchip: enable dma for uart and mmc on rk3066a
ARM: dts: rockchip: fix TSADC reset node for rk3066a
The Boot and Power Management Processor (BPMP) is a co-processor found
in Tegra SoCs. It is designed to handle the early stages of the boot
process as well as to offload power management tasks (such as clocks,
resets, powergates, ...).
The binding document defines the resources that are used by the BPMP
firmware, which implements the interprocessor communication (IPC)
between the CPU and the BPMP.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
32bit devicetree changes for Rockchip including removal of skeleton.dtsi
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
* tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
ARM: dts: rockchip: Set sdmmc frequency at boot time for rk3066a
ARM: dts: rockchip: use pin constants to describe gpios on Popmetal-RK3288
include: dt-bindings: Add GPIO pin index definition for rockchip pinctrl
ARM: dts: rockchip: Add rk3066 MK808 board
devicetree: Add vendor prefix for Rikomagic
ARM: dts: rockchip: initialize rk3066 PLL clock rate
clk: rockchip: Add binding ids for cpu and peri clocks on rk3066
ARM: dts: rockchip: enable HS200/DDR52 mode for emmc on rk3288-popmetal
ARM: dts: rockchip: Support UHS mode for SD card on PopMetal-RK3288 board
ARM: dts: rockchip: remove always-on and boot-on from vcc_sd for px3-evb
ARM: dts: rockchip: update compatible strings for Rockchip efuse
ARM: dts: rockchip: add rockchip PX3 Evaluation board
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3xxx boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk322x boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3036 boards
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3xxx.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3288.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk322x.dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull Allwinner clock changes from Maxime Ripard:
The usual patches from us, but most notably the introduction of the A64
clocks unit.
* tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: sun8i-h3: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: sun8i-a23: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: Add A64 clocks
clk: sunxi-ng: Implement minimum for multipliers
clk: sunxi-ng: Add minimums for all the relevant structures and clocks
clk: sunxi-ng: Finish to convert to structures for arguments
clk: sunxi-ng: Remove the use of rational computations
clk: sunxi-ng: Rename the internal structures
clk: sunxi: mod0: improve function-level documentation
Pull i.MX clock updates from Shawn Guo:
- A patch series to fix the long standing issue with glitchy parent
mux of ldb_di_clk, which can hang up LVDS display when ipu_di_clk
is sourced from ldb_di_clk.
- A patch to add imx6ull clock support on top of imx6ul clock driver.
* tag 'imx-clk-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx: clk-imx6ul: add clk support for imx6ull
clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK
clk: imx6: Make the LDB_DI0 and LDB_DI1 clocks read-only
clk: imx6: Mask mmdc_ch1 handshake for periph2_sel and mmdc_ch1_axi_podf
Add the dt-bindings header for the rk1108, that gets shared
between the clock controller and the clock references in the dts.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull Rockchip clk driver updates from Heiko Stuebner:
PLL initialization for PLLs having both an integral and fractional mode
(rk3036, rk3399) does now take into account the mode that the PLL is
actually running at.
As always also some additional and optimized PLL rates for rk3066 and
rk3399, some additional clock ids for rk3066 and some additional clocks
on rk3399 are now sucessfully handled inside their respective driver.
* tag 'v4.10-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: Ignore frac divisor for PLL equivalence when it's unused
clk: rockchip: remove more CLK_IGNORE_UNUSED for rk3399 clocktree
clk: rockchip: add 400MHz to rk3066 clock rates table
clk: rockchip: optimize 800MHz and 1GHz pll rates on RK3399
clk: rockchip: Use clock ids for cpu and peri clocks on rk3066
clk: rockchip: Add binding ids for cpu and peri clocks on rk3066
clk: rockchip: add 533.25MHz to rk3399 clock rates table
Add CRG driver for Hi3516CV300 SoC. CRG(Clock and Reset
Generator) module generates clock and reset signals used
by other module blocks on SoC.
Signed-off-by: Pan Wen <wenpan@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add CRG driver for Hi3798CV200 SoC. CRG(Clock and Reset
Generator) module generates clock and reset signals used
by other module blocks on SoC.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove useless braces for single line if]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
[sboyd@codeaurora.org: Dropped unused and incorrect GDSC defines]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add macros usable by the device tree sources to reference the R8A7745
CPG clocks by index. The data comes from Table 7.2c in revision 1.00 of
the RZ/G Series User's Manual.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add macros usable by the device tree sources to reference the R8A7743 CPG
clocks by index. The data comes from Table 7.2b in revision 1.00 of the
RZ/G Series User's Manual.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
