The function tipc_msg_extract() is using skb_clone() to clone inner
messages from a message bundle buffer. Although this method is safe,
it has an undesired effect that each buffer clone inherits the
true-size of the bundling buffer. As a result, the buffer clone
almost always ends up with being copied anyway by the message
validation function. This makes the cloning into a sub-optimization.
In this commit we take the consequence of this realization, and copy
each inner message to a separately allocated buffer up front in the
extraction function.
As a bonus we can now eliminate the two cases where we had to copy
re-routed packets that may potentially go out on the wire again.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Publications for TIPC_CLUSTER_SCOPE and TIPC_ZONE_SCOPE are in all
aspects handled the same way, both on the publishing node and on the
receiving nodes.
Despite previous ambitions to the contrary, this is never going to change,
so we take the conseqeunce of this and obsolete TIPC_ZONE_SCOPE and related
macros/functions. Whenever a user is doing a bind() or a sendmsg() attempt
using ZONE_SCOPE we translate this internally to CLUSTER_SCOPE, while we
remain compatible with users and remote nodes still using ZONE_SCOPE.
Furthermore, the non-formalized scope value 0 has always been permitted
for use during lookup, with the same meaning as ZONE_SCOPE/CLUSTER_SCOPE.
We now permit it even as binding scope, but for compatibility reasons we
choose to not change the value of TIPC_CLUSTER_SCOPE.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d618d09a68 ("tipc: enforce valid ratio between skb truesize
and contents") we introduced a test for ensuring that the condition
truesize/datasize <= 4 is true for a received buffer. Unfortunately this
test has two problems.
- Because of the integer arithmetics the test
if (skb->truesize / buf_roundup_len(skb) > 4) will miss all
ratios [4 < ratio < 5], which was not the intention.
- The buffer returned by skb_copy() inherits skb->truesize of the
original buffer, which doesn't help the situation at all.
In this commit, we change the ratio condition and replace skb_copy()
with a call to skb_copy_expand() to finally get this right.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending node local messages the code is using an 'mtu' of 66060
bytes to avoid unnecessary fragmentation. During situations of low
memory tipc_msg_build() may sometimes fail to allocate such large
buffers, resulting in unnecessary send failures. This can easily be
remedied by falling back to a smaller MTU, and then reassemble the
buffer chain as if the message were arriving from a remote node.
At the same time, we change the initial MTU setting of the broadcast
link to a lower value, so that large messages always are fragmented
into smaller buffers even when we run in single node mode. Apart from
obtaining the same advantage as for the 'fallback' solution above, this
turns out to give a significant performance improvement. This can
probably be explained with the __pskb_copy() operation performed on the
buffer for each recipient during reception. We found the optimal value
for this, considering the most relevant skb pool, to be 3744 bytes.
Acked-by: Ying Xue <ying.xue@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket level flow control is based on the assumption that incoming
buffers meet the condition (skb->truesize / roundup(skb->len) <= 4),
where the latter value is rounded off upwards to the nearest 1k number.
This does empirically hold true for the device drivers we know, but we
cannot trust that it will always be so, e.g., in a system with jumbo
frames and very small packets.
We now introduce a check for this condition at packet arrival, and if
we find it to be false, we copy the packet to a new, smaller buffer,
where the condition will be true. We expect this to affect only a small
fraction of all incoming packets, if at all.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following commits we will need to handle multiple incoming and
rejected/returned buffers in the function socket.c::filter_rcv().
As a preparation for this, we generalize the function by handling
buffer queues instead of individual buffers. We also introduce a
help function tipc_skb_reject(), and rename filter_rcv() to
tipc_sk_filter_rcv() in line with other functions in socket.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bundling message is received, the function tipc_link_input()
calls function tipc_msg_extract() to unbundle all inner messages of
the bundling message before adding them to input queue.
The function tipc_msg_extract() just clones all inner skb for all
inner messagges from the bundling skb. This means that the skb
headroom of an inner message overlaps with the data part of the
preceding message in the bundle.
If the message in question is a name addressed message, it may be
subject to a secondary destination lookup, and eventually be sent out
on one of the interfaces again. But, since what is perceived as headroom
by the device driver in reality is the last bytes of the preceding
message in the bundle, the latter will be overwritten by the MAC
addresses of the L2 header. If the preceding message has not yet been
consumed by the user, it will evenually be delivered with corrupted
contents.
This commit fixes this by uncloning all messages passing through the
function tipc_msg_lookup_dest(), hence ensuring that the headroom
is always valid when the message is passed on.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e3a77561e7 ("tipc: split up function tipc_msg_eval()"),
we have updated the function tipc_msg_lookup_dest() to set the error
codes to negative values at destination lookup failures. Thus when
the function sets the error code to -TIPC_ERR_NO_NAME, its inserted
into the 4 bit error field of the message header as 0xf instead of
TIPC_ERR_NO_NAME (1). The value 0xf is an unknown error code.
In this commit, we set only positive error code.
Fixes: e3a77561e7 ("tipc: split up function tipc_msg_eval()")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_msg_reverse(), we assign skb attributes to local pointers
in stack at startup. This is followed by skb_linearize() and for
cloned buffers we perform skb relocation using pskb_expand_head().
Both these methods may update the skb attributes and thus making
the pointers incorrect.
In this commit, we fix this error by ensuring that the pointers
are re-assigned after any of these skb operations.
Fixes: 29042e19f2 ("tipc: let function tipc_msg_reverse() expand header
when needed")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function msg_reverse(), we reverse the header while trying to
reuse the original buffer whenever possible. Those rejected/returned
messages are always transmitted as unicast, but the msg_non_seq field
is not explicitly set to zero as it should be.
We have seen cases where multicast senders set the message type to
"NOT dest_droppable", meaning that a multicast message shorter than
one MTU will be returned, e.g., during receive buffer overflow, by
reusing the original buffer. This has the effect that even the
'msg_non_seq' field is inadvertently inherited by the rejected message,
although it is now sent as a unicast message. This again leads the
receiving unicast link endpoint to steer the packet toward the broadcast
link receive function, where it is dropped. The affected unicast link is
thereafter (after 100 failed retransmissions) declared 'stale' and
reset.
We fix this by unconditionally setting the 'msg_non_seq' flag to zero
for all rejected/returned messages.
Reported-by: Canh Duc Luu <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep under a rcu read lock in tipc_msg_reverse, and the
function call path is:
tipc_l2_rcv_msg (acquire the lock by rcu_read_lock)
tipc_rcv
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
tipc_node_broadcast
tipc_node_xmit_skb
tipc_node_xmit
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
To fix it, "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC multicast messages are currently carried over a reliable
'broadcast link', making use of the underlying media's ability to
transport packets as L2 broadcast or IP multicast to all nodes in
the cluster.
When the used bearer is lacking that ability, we can instead emulate
the broadcast service by replicating and sending the packets over as
many unicast links as needed to reach all identified destinations.
We now introduce a new TIPC link-level 'replicast' service that does
this.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.
In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When extracting an individual message from a received "bundle" buffer,
we just create a clone of the base buffer, and adjust it to point into
the right position of the linearized data area of the latter. This works
well for regular message reception, but during periods of extremely high
load it may happen that an extracted buffer, e.g, a connection probe, is
reversed and forwarded through an external interface while the preceding
extracted message is still unhandled. When this happens, the header or
data area of the preceding message will be partially overwritten by a
MAC header, leading to unpredicatable consequences, such as a link
reset.
We now fix this by ensuring that the msg_reverse() function never
returns a cloned buffer, and that the returned buffer always contains
sufficient valid head and tail room to be forwarded.
Reported-by: Erik Hugne <erik.hugne@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code path for receiving broadcast packets is currently distinct
from the unicast path. This leads to unnecessary code and data
duplication, something that can be avoided with some effort.
We now introduce separate per-peer tipc_link instances for handling
broadcast packet reception. Each receive link keeps a pointer to the
common, single, broadcast link instance, and can hence handle release
and retransmission of send buffers as if they belonged to the own
instance.
Furthermore, we let each unicast link instance keep a reference to both
the pertaining broadcast receive link, and to the common send link.
This makes it possible for the unicast links to easily access data for
broadcast link synchronization, as well as for carrying acknowledges for
received broadcast packets.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit simplifies the broadcast link transmission function, by
leveraging previous changes to the link transmission function and the
broadcast transmission link life cycle.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for message reassembly is erroneously assuming that
the the first arriving fragment buffer always is linear, and then goes
ahead resetting the fragment list of that buffer in anticipation of
more arriving fragments.
However, if the buffer already happens to be non-linear, we will
inadvertently drop the already attached fragment list, and later
on trig a BUG() in __pskb_pull_tail().
We see this happen when running fragmented TIPC multicast across UDP,
something made possible since
commit d0f91938be ("tipc: add ip/udp media type")
We fix this by not resetting the fragment list when the buffer is non-
linear, and by initiatlizing our private fragment list tail pointer to
the tail of the existing fragment list.
Fixes: commit d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous commits, we are guaranteed that no packets
of type LINK_PROTOCOL or with illegal sequence numbers will be
attempted added to the link deferred queue. This makes it possible to
make some simplifications to the sorting algorithm in the function
tipc_skb_queue_sorted().
We also alter the function so that it will drop packets if one with
the same seqeunce number is already present in the queue. This is
necessary because we have identified weird packet sequences, involving
duplicate packets, where a legitimate in-sequence packet may advance to
the head of the queue without being detected and de-queued.
Finally, we make this function outline, since it will now be called only
in exceptional cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msg pointer into header may change after skb linearization.
We must reinitialize it after calling skb_linearize to prevent
operating on a freed or invalid pointer.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Tamás Végh <tamas.vegh@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message is received in a socket, one of the call chains
tipc_sk_rcv()->tipc_sk_enqueue()->filter_rcv()(->tipc_sk_proto_rcv())
or
tipc_sk_backlog_rcv()->filter_rcv()(->tipc_sk_proto_rcv())
are followed. At each of these levels we may encounter situations
where the message may need to be rejected, or a new message
produced for transfer back to the sender. Despite recent
improvements, the current code for doing this is perceived
as awkward and hard to follow.
Leveraging the two previous commits in this series, we now
introduce a more uniform handling of such situations. We
let each of the functions in the chain itself produce/reverse
the message to be returned to the sender, but also perform the
actual forwarding. This simplifies the necessary logics within
each function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we use the code sequence
if (msg_reverse())
tipc_link_xmit_skb()
at numerous locations in socket.c. The preparation of arguments
for these calls, as well as the sequence itself, makes the code
unecessarily complex.
In this commit, we introduce a new function, tipc_sk_respond(),
that performs this call combination. We also replace some, but not
yet all, of these explicit call sequences with calls to the new
function. Notably, we let the function tipc_sk_proto_rcv() use
the new function to directly send out PROBE_REPLY messages,
instead of deferring this to the calling tipc_sk_rcv() function,
as we do now.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shortest TIPC message header, for cluster local CONNECTED messages,
is 24 bytes long. With this format, the fields "dest_node" and
"orig_node" are optimized away, since they in reality are redundant
in this particular case.
However, the absence of these fields leads to code inconsistencies
that are difficult to handle in some cases, especially when we need
to reverse or reject messages at the socket layer.
In this commit, we concentrate the handling of the absent fields
to one place, by letting the function tipc_msg_reverse() reallocate
the buffer and expand the header to 32 bytes when necessary. This
means that the socket code now can assume that the two previously
absent fields are present in the header when a message needs to be
rejected. This opens up for some further simplifications of the
socket code.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the packet sequence number is updated and added to each
packet at the moment a packet is added to the link backlog queue.
This is wasteful, since it forces the code to traverse the send
packet list packet by packet when adding them to the backlog queue.
It would be better to just splice the whole packet list into the
backlog queue when that is the right action to do.
In this commit, we do this change. Also, since the sequence numbers
cannot now be assigned to the packets at the moment they are added
the backlog queue, we do instead calculate and add them at the moment
of transmission, when the backlog queue has to be traversed anyway.
We do this in the function tipc_link_push_packet().
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
