Currently, we export serial8250_rx_chars, which does a whole bunch of
reads from the 8250 data register, without any form of flow control
between reads.
An upcoming change to the aspeed vuart driver implements more
fine-grained flow control in the interrupt handler, requiring
character-at-a-time control over the rx path.
This change exports serial8250_read_char to allow this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the timers where based on the classic timers, giving a too
coarse resolution on systems with configs of less than 1000 HZ.
This patch changes the rs485 timers to hrtimers.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementation of software emulation of RS485 direction handling is based
on omap_serial driver.
Before and after transmission RTS is set to the appropriate value.
Note that before calling serial8250_em485_init() the caller has to
ensure that UART will interrupt when shift register empty. Otherwise,
emultaion cannot be used.
Both serial8250_em485_init() and serial8250_em485_destroy() are
idempotent functions.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed71871bed ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override
However recent updates to core, specifically ebc5e20082 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3fee
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header file, include/linux/serial_8250.h, contains references to
UART_LSR_BRK_ERROR_BITS and UART_MSR_ANY_DELTA that are defined in
<linux/serial_reg.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; separate RSA probe and resource management
from base port operations. Override base port operations for the
config_port(), request_port() and release_port() methods to
implement the optional RSA probe and resource management only in
the universal/legacy 8250 driver.
Introduce 'probe' flags for 8250 ports, which allows drivers higher
up the driver stack to enable optional probes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250 split; decouple irq setup/teardown and handler from
core port operations.
Introduce setup_irq() and release_irq() 8250 driver methods; the 8250
core will use these methods to install and remove irq handling for
the given 8250 port.
Refactor irq chain linking/unlinking from 8250 core into
univ8250_setup_irq()/univ8250_release_irq() for the universal 8250 driver.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
setup_earlycon() will now match and register the desired earlycon
from the param string (as if 'earlycon=...' had been set on the
command line). Use setup_earlycon() from existing arch call sites
which start an earlycon directly.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).
The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.
Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.
Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.
This workaround is disabled for omap_8250 (which uses different divisor
programming).
Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kbuild test robot wrote me:
| make.cross ARCH=powerpc
|>> ERROR: ".__xchg_called_with_bad_pointer" [drivers/tty/serial/8250/8250.ko] undefined!
The generic implementation of xchg() on arm and x86 works for variables of
size one bye (char). According to the report powerpc does not support
xchg() for one byte sized variables and looking further it seems also to
be the same case for sparc and tile (or for 10 out of 26 architectures
which provide a custom implementation).
For that reason I increase the size of the variable from one to four
bytes to get it work on powerpc (and the others).
Reported-By: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.
NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.
v5…v8:
- drop RPM from serial8250_set_mctrl() it will be used in
restore path which already has RPM active and holds
dev->power.lock
v4…v5:
- add a wrapper around rpm function and introduce UART_CAP_RPM
to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
- added runtime to the console code
- removed device_may_wakeup() from serial8250_set_sleep()
Cc: mika.westerberg@linux.intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.
v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.
If no handler is defined the 8250 driver will work as usual.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure
drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
include/linux/serial_8250.h | 3 +++
2 files changed, 42 insertions(+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
