We're supposed to pass the number of elements in the mtk_recv_pkts, not
the number of bytes.
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Like all the other UART protocols, introduce a configuration option for
Realtek based serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a driver based on serdev driver for the MediaTek serial protocol
based on running H:4, which can enable the built-in Bluetooth device inside
MT7622 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This driver was recently updated to use serdev, so add the appropriate
dependency. Without this one can get compiler warnings like this if
CONFIG_SERIAL_DEV_BUS is not enabled:
CC [M] drivers/bluetooth/hci_h5.o
drivers/bluetooth/hci_h5.c:934:36: warning: ‘h5_serdev_driver’ defined but not used [-Wunused-variable]
static struct serdev_device_driver h5_serdev_driver = {
^~~~~~~~~~~~~~~~
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In function qca_setup, we set initial and operating speeds for Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.
These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some of the QCA BTSoC ROME functions, are used for different versions
or different make of BTSoC's. Instead of duplicating the same functions
for new chip, update names of the functions that are used for both
chips to keep this generic and would help in future when we would have
new BT SoC. To have generic text in logs updated from ROME to QCA where
ever possible. This avoids confusion to user, when using the future
Qualcomm Bluetooth SoC's. Updated BT_DBG, BT_ERR and BT_INFO with
bt_dev_dbg, bt_dev_err and bt_dev_info where ever applicable.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for the enable and device-wake GPIOs used on ACPI enumerated
RTL8723BS devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement support for the RTL8723BS chip.
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop broken GPIO code]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allow vendor-specific setup, open, and close functions to be defined.
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop dt support]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add basic support for serdev enumerated devices, note sine this does
not (yet) declare any of / ACPI ids to bind to atm this is a nop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The contents of the rtl_bt/rtlXXXX_config.bin file may be board specific
allow the caller of btrtl_initialize to specify a postfix identifying
the board, which if specified will make btrtl_initialize look for
rtl_bt/rtlXXXX_config-<postfix>.bin instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Realtek RTL8723BS and RTL8723DS chipsets are SDIO wifi chips. They
also contain a Bluetooth module which is connected via UART to the host.
Realtek's userspace initialization tool (rtk_hciattach) differentiates
these two via the HCI version and revision returned by the
HCI_OP_READ_LOCAL_VERSION command.
Additionally we apply these checks only the for UART devices. Everything
else is assumed to be a "RTL8723B" which was originally supported by the
driver (communicating via USB).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The UART settings are embedded in the config blob. This has to be parsed
to successfully initialize the Bluetooth part of the RTL8723BS (which is
an SDIO chip, but the Bluetooth part is connected via UART).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
- send H5 sync pattern (already supported by hci_h5)
- get LMP version (already supported by btrtl)
- get ROM version (already supported by btrtl)
- load the firmware and config for the current chipset (already
supported by btrtl)
- read UART settings from the config blob (part of this patch)
- send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
- change the baudrate and flow control settings on the host
- send the firmware and config blob to the device (already supported by
btrtl)
Sending the last firmware and config blob download command
(rtl_download_cmd) fails if the UART settings are not updated
beforehand. This is presumably because the device applies the config
right after the firmware and config blob download - which means that at
this point the host is using different UART settings than the device
(which will obviously result in non-working communication).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Consistently use rtl_dev_err and rtl_dev_info everywhere for messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This prepares the btrtl code so it can be used to initialize Bluetooth
modules connected via UART (these are found for example on the RTL8723BS
and RTL8723DS SDIO chips, which come with an embedded UART Bluetooth
module).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
1) send H5 sync pattern (already supported by hci_h5)
2) get LMP version (already supported by btrtl)
3) get ROM version (already supported by btrtl)
4) load the firmware and config for the current chipset (already
supported by btrtl)
5) read UART settings from the config blob (currently not supported)
6) send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
7) change the baudrate and flow control settings on the host
8) send the firmware and config blob to the device (already supported by
btrtl)
The main reason why the initialization has to be split is step #7. This
requires changes to the underlying "bus", which should be kept outside
of the "generic" btrtl driver.
The idea for this split is borrowed from the btbcm driver but adjusted
where needed (the btrtl driver for example needs two blobs: firmware and
config, while the btbcm only needs one).
This also prepares the code for step #5 (parsing the config blob) by
centralizing the code which loads the firmware and config blobs and
storing the result in the new struct btrtl_device_info.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace the BT_ERR functions with bt_dev_err to get a consistent error
printout that always prefixes the HCI device identifier.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Issue description: Intel 7265 shares the same RF with Wifi and BT.
In the shutdown scenario turn off BT, followed by turn WiFi off
and on causing error in RF calibration in WiFi Module
Solution: before shutdown BT ensure any RF activity to clear by
HCI reset command.
Reference Logs:
ERR kernel: [ 386.193284] iwlwifi 0000:01:00.0: Failed to run INIT calibrations: -5
ERR kernel: [ 386.193298] iwlwifi 0000:01:00.0: Failed to run INIT ucode: -5
ERR kernel: [ 386.193309] iwlwifi 0000:01:00.0: Failed to start RT ucode: -5
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Singed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_open() and qca_set_baudrate() are never called in atomic context.
They call kzalloc() and bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by intel_dequeue(),
which is never called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
