Add interface to support Power Sourcing Equipment. At current step it
provides generic way to address all variants of PSE devices as defined
in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4
PoDL Power Sourcing Equipment (PSE).
Currently supported and mandatory objects are:
IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus
IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl
This is minimal interface needed to control PSE on each separate
ethernet port but it provides not all mandatory objects specified in
IEEE 802.3-2018.
Since "PoDL PSE" and "PSE" have similar names, but some different values
I decide to not merge them and keep separate naming schema. This should
allow as to be as close to IEEE 802.3 spec as possible and avoid name
conflicts in the future.
This implementation is connected to PHYs instead of MACs because PSE
auto classification can potentially interfere with PHY auto negotiation.
So, may be some extra PHY related initialization will be needed.
With WIP version of ethtools interaction with PSE capable link looks
as following:
$ ip l
...
5: t1l1@eth0: <BROADCAST,MULTICAST> ..
...
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: disabled
PoDL PSE Power Detection Status: disabled
$ ethtool --set-pse t1l1 podl-pse-admin-control enable
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: enabled
PoDL PSE Power Detection Status: delivering power
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return value of nla_nest_start(). When starting the entry
level nested attributes, if the tailroom of socket buffer is
insufficient to store the attribute header and payload, the return value
will be NULL.
There is, however, no real bug here since if the skb is full
nla_put_be16() will fail as well and we'll error out.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Link: https://lore.kernel.org/r/20220921181716.1629541-1-floridsleeves@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The actual presence check for the header is in
ethnl_parse_header_dev_get() but it's a few layers in,
and already has a ton of arguments so let's just pick
the low hanging fruit and check for missing header in
the default request handler.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Strset needs ETHTOOL_A_STRINGSET_ID, use it as an example of
reporting attrs missing in nests.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Function fallback_set_params() checks if the module type returned
by a driver is ETH_MODULE_SFF_8079 and in this case it assumes
that buffer returns a concatenated content of page A0h and A2h.
The check is wrong because the correct type is ETH_MODULE_SFF_8472.
Fixes: 96d971e307 ("ethtool: Add fallback to get_module_eeprom from netlink command")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220616160856.3623273-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the implementation of ethtool_convert_link_mode_to_legacy_u32(), which
is supposed to return false if src has bits higher than 31 set. The current
implementation uses the complement of bitmap_fill(ext, 32) to test high
bits of src, which is wrong as bitmap_fill() fills _with long granularity_,
and sizeof(long) can be > 4. No users of this function currently check the
return value, so the bug was dormant.
Also remove the check for __ETHTOOL_LINK_MODE_MASK_NBITS > 32, as the enum
ethtool_link_mode_bit_indices contains far beyond 32 values. Using
find_next_bit() to test the src bitmask works regardless of this anyway.
Signed-off-by: Marco Bonelli <marco@mebeim.net>
Link: https://lore.kernel.org/r/20220609134900.11201-1-marco@mebeim.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdev reference helpers have a dev_ prefix for historic
reasons. Renaming the old helpers would be too much churn
but we can rename the tracking ones which are relatively
recent and should be the default for new code.
Rename:
dev_hold_track() -> netdev_hold()
dev_put_track() -> netdev_put()
dev_replace_track() -> netdev_ref_replace()
Link: https://lore.kernel.org/r/20220608043955.919359-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently these two checks in ethnl_set_rings are added after rtnl_lock()
which will do useless works if the request is invalid.
So this patch moves these checks before the rtnl_lock() to avoid these
costs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently tx push is a standard driver feature which controls use of a fast
path descriptor push. So this patch extends the ringparam APIs and data
structures to support set/get tx push by ethtool -G/g.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For applications running on a mix of platforms it's useful
to have a clear indication whether host's NIC supports the
geometry requirements of TCP zero-copy. TCP zero-copy Rx
requires data to be neatly placed into memory pages.
Most NICs can't do that.
This patch is adding GET support only, since the NICs
I work with either always have the feature enabled or
enable it whenever MTU is set to jumbo. In other words
I don't need SET. But adding set should be trivial.
(The only note on SET is that we will likely want
the setting to be "sticky" and use 0 / `unknown`
to reset it back to driver default.)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool_get_phy_stats(), the phydev varaible is set to
dev->phydev but dev->phydev is still used. Replace
dev->phydev uses with phydev.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment here will be overwritten, so it should be deleted
The clang_analyzer complains as follows:
net/ethtool/netlink.c:
Value stored to 'ret' is never read
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
Commit 0976b888a1 ("ethtool: fix null-ptr-deref on ref tracker")
made the write to req_info.dev conditional, but as Eric points out
in a different follow up the structure is often allocated on the
stack and not kzalloc()'d so seems safer to always write the dev,
in case it's garbage on input.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems I missed that most ethnl_parse_header_dev_get() callers
declare an on-stack struct ethnl_req_info, and that they simply call
dev_put(req_info.dev) when about to return.
Add ethnl_parse_header_dev_put() helper to properly untrack
reference taken by ethnl_parse_header_dev_get().
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev can be a NULL here, not all requests set require_dev.
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
