Current u-boot doesn't seem to take into account that some GPIOs are
configured as inputs/outputs of certain peripherals on power-up. This
means it ends up configuring some GPIOs as inputs to more than one
peripheral which the documentation explicitly says is illegal. Similarly
it also ends up configuring more than one GPIO as output of the same
peripheral. While not explicitly mentioned by the documentation this
also seems like a bad idea.
The easiest way to remedy this mess is to just disconnect all GPIOs from
peripherals and have our pinmux configuration set everything up
properly. This, however, means that we'd disconnect the serial console
from its pins for a while, so add a device tree property to keep
certain GPIOs from being reset.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Pull interrupt updates from Thomas Gleixner:
"Core code:
- Provide a generic wrapper which can be utilized in drivers to
handle the problem of force threaded demultiplex interrupts on RT
enabled kernels. This avoids conditionals and horrible quirks in
drivers all over the place
- Fix up affected pinctrl and GPIO drivers to make them cleanly RT
safe
Interrupt drivers:
- A new driver for the FSL MU platform specific MSI implementation
- Make irqchip_init() available for pure ACPI based systems
- Provide a functional DT binding for the Realtek RTL interrupt chip
- The usual DT updates and small code improvements all over the
place"
* tag 'irq-core-2022-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
irqchip: IMX_MU_MSI should depend on ARCH_MXC
irqchip/imx-mu-msi: Fix wrong register offset for 8ulp
irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap
dt-bindings: irqchip: Describe the IMX MU block as a MSI controller
irqchip: Add IMX MU MSI controller driver
dt-bindings: irqchip: renesas,irqc: Add r8a779g0 support
irqchip/gic-v3: Fix typo in comment
dt-bindings: interrupt-controller: ti,sci-intr: Fix missing reg property in the binding
dt-bindings: irqchip: ti,sci-inta: Fix warning for missing #interrupt-cells
irqchip: Allow extra fields to be passed to IRQCHIP_PLATFORM_DRIVER_END
platform-msi: Export symbol platform_msi_create_irq_domain()
irqchip/realtek-rtl: use parent interrupts
dt-bindings: interrupt-controller: realtek,rtl-intc: require parents
irqchip/realtek-rtl: use irq_domain_add_linear()
irqchip: Make irqchip_init() usable on pure ACPI systems
bcma: gpio: Use generic_handle_irq_safe()
gpio: mlxbf2: Use generic_handle_irq_safe()
platform/x86: intel_int0002_vgpio: Use generic_handle_irq_safe()
ssb: gpio: Use generic_handle_irq_safe()
pinctrl: amd: Use generic_handle_irq_safe()
...
Pull pin control updates from Linus Walleij:
"There is nothing exciting going on, no core changes, just a few
drivers and cleanups.
New drivers:
- Cypress CY8C95x0 chip pin control support, along with an immediate
cleanup
- Mediatek MT8188 SoC pin control support
- Qualcomm SM8450 and SC8280XP LPASS (low power audio subsystem) pin
control support
- Qualcomm PM7250, PM8450
- Rockchip RV1126 SoC pin control support
Improvements:
- Fix some missing pins in the Armada 37xx driver
- Convert Broadcom and Nomadik drivers to use PINCTRL_PINGROUP()
macro
- Fix some GPIO irq_chips to be immutable
- Massive Qualcomm device tree binding cleanup, with more to come"
* tag 'pinctrl-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (119 commits)
MAINTAINERS: adjust STARFIVE JH7100 PINCTRL DRIVER after file movement
pinctrl: starfive: Rename "pinctrl-starfive" to "pinctrl-starfive-jh7100"
pinctrl: Create subdirectory for StarFive drivers
dt-bindings: pinctrl: st,stm32: Document interrupt-controller property
dt-bindings: pinctrl: st,stm32: Document gpio-hog pattern property
dt-bindings: pinctrl: st,stm32: Document gpio-line-names
pinctrl: st: stop abusing of_get_named_gpio()
pinctrl: wpcm450: Correct the fwnode_irq_get() return value check
pinctrl: bcm: Remove unused struct bcm6328_pingroup
pinctrl: qcom: restrict drivers per ARM/ARM64
pinctrl: bcm: ns: Remove redundant dev_err call
gpio: rockchip: request GPIO mux to pinctrl when setting direction
pinctrl: rockchip: add pinmux_ops.gpio_set_direction callback
pinctrl: cy8c95x0: Align function names in cy8c95x0_pmxops
pinctrl: cy8c95x0: Drop atomicity on operations on push_pull
pinctrl: cy8c95x0: Lock register accesses in cy8c95x0_set_mux()
pinctrl: sunxi: sun50i-h5: Switch to use dev_err_probe() helper
pinctrl: stm32: Switch to use dev_err_probe() helper
dt-bindings: qcom-pmic-gpio: Add PM7250B and PM8450 bindings
pinctrl: qcom: spmi-gpio: Add compatible for PM7250B
...
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
Pin descriptions for this chip only look like standard GPIO device tree
descriptions, while in fact they contain additional data (in excess of
number of cells specified in description of gpio controllers). They also
refer to only pins/gpios belonging to the driver and not to arbitrary
gpio in the system.
Because we want to stop exporting OF-specific handlers from gpiolib-of,
let's parse the pin reference ourself instead of trying to call
of_get_named_gpio().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/YzSsgoVoJn4+mSpv@google.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before the split of gpio and pinctrl sections in their own driver,
rockchip_set_mux was called in pinmux_ops.gpio_set_direction for
configuring a pin in its GPIO function.
This is essential for cases where pinctrl is "bypassed" by gpio
consumers otherwise the GPIO function is not configured for the pin and
it does not work. Such was the case for the sysfs/libgpiod userspace
GPIO handling.
Let's re-implement the pinmux_ops.gpio_set_direction callback so that
the gpio subsystem can request from the pinctrl driver to put the pin in
its GPIO function.
Fixes: 9ce9a02039 ("pinctrl/rockchip: drop the gpio related codes")
Cc: stable@vger.kernel.org
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220930132033.4003377-2-foss+kernel@0leil.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On PREEMPT_RT enabled kernels the demultiplex interrupt handler is force
threaded and runs with interrupts enabled. The invocation of
generic_handle_domain_irq() with interrupts enabled triggers a lockdep
warning due to a non-irq safe lock acquisition.
Instead of disabling interrupts on the driver level, use
generic_handle_domain_irq_safe().
[ tglx: Split out from combo patch ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/YnkfWFzvusFFktSt@linutronix.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215954
Add support for SPMI PMIC GPIO subtypes GPIO_LV_VIN2 and
GPIO_MV_VIN3.
GPIO_LV_VIN2 GPIOs support two input reference voltages: VIN0 and
VIN1. These are typically connected to 1.8 V and 1.2 V supplies
respectively.
GPIO_MV_VIN3 GPIOs support three input reference voltages: VIN0,
VIN1, and VIN2. These are typically connected to Vph, 1.8 V, and
1.2 V supplies respectively.
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Link: https://lore.kernel.org/r/20220912210624.4527-2-quic_amelende@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b6d09f7807 ("pinctrl: nomadik: Drop U8540/9540 support") removes
the DB8540 pin controller driver and its config PINCTRL_DB8540.
There is some code left-over in the generic nomadik pinctrl driver, i.e.,
drivers/pinctrl/nomadik/pinctrl-nomadik.{ch}, that is still around for the
removed DB8540 pin controller driver.
Remove this remaining dead code.
This issue was discovered with ./scripts/checkkconfigsymbols.py.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220919065435.27747-1-lukas.bulwahn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
