On ACPI boards, when we cannot get the GPIOs to do a reset ourselves
if necessary, call acpi_device_fix_up_power() to force the ACPI _PS0
method to run.
On some devices without proper GPIO descriptions this will reset
the touchscreen for us and this may be necessary for us to be able
to communicate to the touchscreen at all.
Specifically on an Aya Neo Next this change will cause the _PS0()
ACPI function to call INIT() which does:
Method (INIT, 0, Serialized)
{
TP_I = 0x00A50000
TP_R = 0x00A50000
Sleep (0x0A)
TP_I = 0x00E50000
Sleep (One)
TP_R = 0x00E50000
Sleep (0x06)
TP_I = 0x00A50000
Sleep (0x3C)
TP_I = 0x00041800
}
On older kernels the ACPI core assumed a power-on was necessary by itself
and would run _PS0 before our probe function runs, which can be seen from
the GPIO pin ctrl registers in /sys/kernel/debug/gpio which match
the above hex values with older kernels.
With newer kernels before this change the GPIO pin ctrl registers do not
match, indicating INIT() has not run and probing the touchscreen fails.
This change makes Linux run _PS0() again fixing the touchscreen not working
on the Aya Neo Next.
Reported-and-tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220618210233.208027-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because there is no way to detect if the touchscreen has pen support,
the driver is allocating and registering the input_pen input_dev on
receiving the first pen event.
But this means that the input_dev gets allocated after the request_irq()
call which means that the devm framework will free it before disabling
the irq, leaving a window where the irq handler may run and reference the
free-ed input_dev.
To fix this move the allocation of the input_pen input_dev to before
the request_irq() call, while still only registering it on the first pen
event so that the driver does not advertise pen capability on touchscreens
without it (most goodix touchscreens do not have pen support).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A few small updates to drivers.
Of note we are now deferring probes of i8042 on some Asus devices as
the controller is not ready to respond to queries first time around
when the driver is compiled into the kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Input: goodix - fix memory leak in goodix_firmware_upload
Input: goodix - add id->model mapping for the "9111" model
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Input: iqs626a - prohibit inlining of channel parsing functions
Input: i8042 - add deferred probe support
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
Some Goodix touchscreen controllers, such as for example the GT912,
don't have flash-storage for their firmware.
These models require the OS to load the firmware at runtime, as well as
some other special handling. Add support for this to the goodix driver.
This patch was developed and tested on a Glavey TM800A550L tablet.
Note the "goodix,main-clk" and "firmware-name" device-properties used
by the new code are *not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this properties for now is purely a kernel-internal thing and
the name/working of the properties may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-7-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The config which needs to be send to the controller on some device-models
is model-specific. Allow specifying a model-specific filename through
a device-property, rather then always using a fixed filename.
Note the "goodix,config-name" device-property used by this is
*not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this property for now is purely a kernel-internal thing and
the name/working of the property may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-6-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the goodix_i2c_read() and goodix_i2c_write*() helpers log errors
themselves. This allows removing all the error logging from their callers.
This already results in a nice cleanup with the current code and it also
helps to make the upcoming support for controllers without flash cleaner.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wolfram Sang
Jarrah Gosbell
Uwe Kleine-König
Ondrej Jirman
Dmitry Torokhov
Hans de Goede
Andy Shevchenko
Linus Torvalds