During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.
The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.
The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.
As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:
* i915 has fairly different structures than simpler KMS drivers such
as vc4, so doing some code that works with both proved to be
difficult;
* Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
it would still require to move some parameters currently stored in
private structure that are needed to compute whether the scrambling
is needed or not, and then inform the driver that it needs to be
enabled. Some of those parameters are already in core structures
(drm_display_mode, drm_display_info, bpc), but the output format
isnt't. Adding it is fairly challenging since unlike the TMDS char
rate or mode, there's no consensus on what format to pick in
drivers, so it's not possible to write some generic code that can
depend on it.
For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech
Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.
This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.
Let's move all that logic to a function of its own.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-5-maxime@cerno.tech
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
drm-misc-next for v6.1:
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f0c71766-61e8-19b7-763a-5fbcdefc633d@linux.intel.com
In vc4_hvs_dump_state() potentially freed resources are protected from
being accessed with drm_dev_enter()/drm_dev_exit().
Also include drm_print_regset32() in the protected section, since
drm_print_regset32() does access memory that is typically mapped via
devm_* calls.
Fixes: 969cfae1f0 ("drm/vc4: hvs: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-5-dakr@redhat.com
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 7cc4214c27 ("drm/vc4: crtc: Switch to drmm_kzalloc")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-4-dakr@redhat.com
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 9872c7a319 ("drm/vc4: plane: Switch to drmm_universal_plane_alloc()")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-3-dakr@redhat.com
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187
("drm/vc4: hdmi: Protect device resources after removal") missed to
unlock the mutex before returning due to drm_dev_enter() indicating the
device being unplugged.
Fixes: cd00ed5187 ("drm/vc4: hdmi: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-2-dakr@redhat.com
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
The field paddr of struct drm_gem_dma_object holds a DMA address, which
might actually be a physical address. However, depending on the platform,
it can also be a bus address or a virtual address managed by an IOMMU.
Hence, rename the field to dma_addr, which is more applicable.
In order to do this renaming the following coccinelle script was used:
```
@@
struct drm_gem_dma_object *gem;
@@
- gem->paddr
+ gem->dma_addr
@@
struct drm_gem_dma_object gem;
@@
- gem.paddr
+ gem.dma_addr
@exists@
typedef dma_addr_t;
symbol paddr;
@@
dma_addr_t paddr;
<...
- paddr
+ dma_addr
...>
@@
symbol paddr;
@@
dma_addr_t
- paddr
+ dma_addr
;
```
This patch is compile-time tested with:
```
make ARCH={x86_64,arm,arm64} allyesconfig
make ARCH={x86_64,arm,arm64} drivers/gpu/drm`
```
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-5-dakr@redhat.com
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy
of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be
more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "FB CMA", but not "GEM CMA".
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-3-dakr@redhat.com
Maxime Ripard
Dave Airlie
Mateusz Kwiatkowski
Daniel Vetter
Danilo Krummrich
Maíra Canal
Linus Torvalds