This code works, but technically it uses "num_in_bus_fmts" before it
has been initialized so it leads to static checker warnings and probably
KMEMsan warnings at run time. Initialize the variable to zero to
silence the warning.
Fixes: f32df58acc ("drm/bridge: Add the necessary bits to support bus format negotiation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YrrIs3hoGcPVmXc5@kili
By depending on devm_drm_panel_bridge_add(), devm_drm_of_get_bridge()
introduces a circular dependency between the modules drm (where
devm_drm_of_get_bridge() ends up) and drm_kms_helper (where
devm_drm_panel_bridge_add() is).
Fix this by moving devm_drm_of_get_bridge() to bridge/panel.c and thus
drm_kms_helper.
Fixes: 87ea95808d ("drm/bridge: Add a function to abstract away panels")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210917180925.2602266-1-maxime@cerno.tech
Display drivers so far need to have a lot of boilerplate to first
retrieve either the panel or bridge that they are connected to using
drm_of_find_panel_or_bridge(), and then either deal with each with ad-hoc
functions or create a drm panel bridge through drm_panel_bridge_add.
In order to reduce the boilerplate and hopefully create a path of least
resistance towards using the DRM panel bridge layer, let's create the
function devm_drm_of_get_bridge() to reduce that boilerplate.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210910130941.1740182-2-maxime@cerno.tech
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector needs to be
moved to the display controller driver.
To avoid code duplication in display controller drivers, add a new
helper to create and manage a DRM connector backed by a chain of
bridges. All connector operations are delegating to the appropriate
bridge in the chain.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-21-laurent.pinchart@ideasonboard.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
drm_bridge_state is extended to describe the input and output bus
configurations. These bus configurations are exposed through the
drm_bus_cfg struct which encodes the configuration of a physical
bus between two components in an output pipeline, usually between
two bridges, an encoder and a bridge, or a bridge and a connector.
The bus configuration is stored in drm_bridge_state separately for
the input and output buses, as seen from the point of view of each
bridge. The bus configuration of a bridge output is usually identical
to the configuration of the next bridge's input, but may differ if
the signals are modified between the two bridges, for instance by an
inverter on the board. The input and output configurations of a
bridge may differ if the bridge modifies the signals internally,
for instance by performing format conversion, or*modifying signals
polarities.
Bus format negotiation is automated by the core, drivers just have
to implement the ->atomic_get_{output,input}_bus_fmts() hooks if they
want to take part to this negotiation. Negotiation happens in reverse
order, starting from the last element of the chain (the one directly
connected to the display) up to the first element of the chain (the one
connected to the encoder).
During this negotiation all supported formats are tested until we find
one that works, meaning that the formats array should be in decreasing
preference order (assuming the driver has a preference order).
Note that the bus format negotiation works even if some elements in the
chain don't implement the ->atomic_get_{output,input}_bus_fmts() hooks.
In that case, the core advertises only MEDIA_BUS_FMT_FIXED and lets
the previous bridge element decide what to do (most of the time, bridge
drivers will pick a default bus format or extract this piece of
information from somewhere else, like a FW property).
v10:
* Add changelog to the commit message
v9:
* No changes
v8:
* Fix a test in drm_atomic_bridge_chain_select_bus_fmts() (Reported by
Jonas)
v7:
* Adapt the code to deal with the fact that not all bridges in the
chain have a bridge state
v5 -> v6:
* No changes
v4:
* Enhance the doc
* Fix typos
* Rename some parameters/fields
* Reword the commit message
v3:
* Fix the commit message (Reported by Laurent)
* Document the fact that bus formats should not be directly modified by
drivers (Suggested by Laurent)
* Document the fact that format order matters (Suggested by Laurent)
* Propagate bus flags by default
* Document the fact that drivers can tweak bus flags if needed
* Let ->atomic_get_{output,input}_bus_fmts() allocate the bus format
array (Suggested by Laurent)
* Add a drm_atomic_helper_bridge_propagate_bus_fmt()
* Mandate that bridge drivers return accurate input_fmts even if they
are known to be the first element in the bridge chain
v2:
* Rework things to support more complex use cases
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed doc in include/drm/drm_bridge.h:69 fmt->format]
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-7-boris.brezillon@collabora.com
So that bridge drivers have a way to check/reject an atomic operation.
The drm_atomic_bridge_chain_check() (which is just a wrapper around
the ->atomic_check() hook) is called in place of
drm_bridge_chain_mode_fixup() (when ->atomic_check() is not implemented,
the core falls back on ->mode_fixup(), so the behavior should stay
the same for existing bridge drivers).
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Fix a NULL pointer dereference
v5 -> v6:
* No changes
v4:
* Add R-bs
v3:
* No changes
v2:
* Clarify the fact that ->atomic_check() is replacing ->mode_fixup()
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-6-boris.brezillon@collabora.com
This way the drm_bridge_funcs interface is consistent with the rest of
the subsystem.
The drivers implementing those hooks are patched too.
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Adjust things to the bridge_state changes
v6:
* Also fixed rcar-du/rcar_lvds.c same as analogix/analogix_dp_core.c
v5:
* No changes
v4:
* Rename func params into old_bridge_state
* Add Laurent's Rb
v3:
* Old state clarification moved to a separate patch
v2:
* Pass the old bridge state
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: renamed state as old_bridge_state in rcar_lvds_atomic_disable]
Reviewed by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-5-boris.brezillon@collabora.com
One of the last remaining objects to not have its atomic state.
This is being motivated by our attempt to support runtime bus-format
negotiation between elements of the bridge chain.
This patch just paves the road for such a feature by adding a new
drm_bridge_state object inheriting from drm_private_obj so we can
re-use some of the existing state initialization/tracking logic.
v10:
* Add changelog to the commit message
v9:
* Clarify the fact that the bridge->atomic_reset() and
{connector,plane,crtc,...}->reset() semantics are different
* Move the drm_atomic_private_obj_init() call back to
drm_bridge_attach()
* Check the presence of ->atomic_duplicate_state instead of
->atomic_reset in drm_atomic_add_encoder_bridges()
* Fix copy&paste errors in the atomic bridge state helpers doc
* Add A-b/R-b tags
v8:
* Move bridge state helpers out of the CONFIG_DEBUGFS section
v7:
* Move helpers, struct-defs, ... to atomic helper files to avoid the
drm -> drm_kms_helper -> drm circular dep
* Stop providing default implementation for atomic state reset,
duplicate and destroy hooks (has to do with the helper/core split)
* Drop all R-b/T-b as helpers have now be moved to other places
v6:
* Made helpers private, removed doc and moved them to satisfy dependencies
* Renamed helpers to _default_
v5:
* Re-introduced the helpers from v4
v4:
* Fix the doc
* Kill default helpers (inlined)
* Fix drm_atomic_get_bridge_state() to check for an ERR_PTR()
* Add Neil's R-b
v3:
* No changes
v2:
* Use drm_for_each_bridge_in_chain()
* Rename helpers to be more consistent with the rest of the DRM API
* Improve/fix the doc
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-2-boris.brezillon@collabora.com
Dan Carpenter
Ville Syrjälä
Douglas Anderson
Maxime Ripard
Cai Huoqing
Laurent Pinchart
Laurent Pinchart
Boris Brezillon