According to the reference manual "The PCA9505 is identical to the
PCA9506 except that it includes 100 kΩ internal pull-up resistors on all
the I/Os." So the pca9506 device can be considered identical to the
pca9505 for the gpio driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for the GPIO controller block in the R-Car V3U (R8A779A0)
SoC, which is very similar to the block found on other R-Car Gen3 SoCs.
However, this block has a new General Input Enable Register (INEN),
whose reset state is to have all inputs disabled.
Enable input for all available pins in probe and resume, to support the
use of the General Input Register (INDT) for reading pin state at all
times. This preserves backwards compatibility with other R-Car Gen3
SoCs, as recommended by the Hardware Manual.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the R-Car GPIO driver treats R-Car Gen2 and R-Car Gen3 GPIO
controllers the same. However, there exist small differences, like the
behavior of the General Input Register (INDT):
- On R-Car Gen1, R-Car Gen2, and RZ/G1, INDT only reflects the state
of an input pin if the GPIO is configured for input,
- On R-Car Gen3 and RZ/G2, INDT always reflects the state of the input
pins.
Hence to accommodate all variants, the driver does not use the INDT
register to read the status of a GPIO line when configured for output,
at the expense of doing 2 or 3 register reads instead of 1.
Given register accesses are slow, change the .get() and .get_multiple()
callbacks to always use INDT to read pin state on SoCs where this is
supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Document the compatible value for the GPIO block in the Renesas R-Car
V3U (R8A779A0) SoC.
While this GPIO block is mostly compatible with GPIO blocks on R-Car
Gen3 SoCs, there are small differences, and one of the new registers
needs to be configured differently from its initial reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Using a helper local variable to store the address of &pdev->dev adds
to readability and allows us to avoid unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Convert the Tegra GPIO driver to use the gpio_irq_chip infrastructure.
This allows a bit of boiler plate to be removed and while at it enables
support for hierarchical domains, which is useful to support PMC wake
events on Tegra210 and earlier.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add compatible string for AM64 SoC in device tree binding of davinci GPIO
modules as the same IP is used.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The ROHM BD70528 and BD71828 GPIO drivers only need the regmap
pointer from parent. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The mandatory compatible values 'renesas,rcar-gen{1,2,3}-gpio' have been
already added to all the respective R-Car Gen{1,2,3} SoC DTSI files,
remove the redundant device specific values from the driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently the HTML output for Documentation/driver-api/gpio/intro.rst
doesn't look right. The lines that start with LOW or HIGH are formatted
in bold, while the next line after each is not bold.
With this patch, the HTML looks better.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiod_*_array_* functions take four arguments, not three.
Additionally, the formatting of the "value_bitmap" line results in
misformatted HTML, so fix that.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Pull LED fix from Pavel Machek:
"One-liner fixing a build problem"
* 'for-rc8-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: rt8515: add V4L2_FLASH_LED_CLASS dependency
Pull Kbuild fixes from Masahiro Yamada:
- Fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
- Use pkg-config for scripts/sign-file.c CFLAGS
* tag 'kbuild-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
scripts: set proper OpenSSL include dir also for sign-file
sparc: remove wrong comment from arch/sparc/include/asm/Kbuild
kbuild: fix CONFIG_TRIM_UNUSED_KSYMS build for ppc64
Pull x86 fixes from Borislav Petkov:
"I kinda knew while typing 'I hope this is the last batch of x86/urgent
updates' last week, Murphy was reading too and uttered 'Hold my
beer!'.
So here's more fixes... Thanks Murphy.
Anyway, three more x86/urgent fixes for 5.11 final. We should be
finally ready (famous last words). :-)
- An SGX use after free fix
- A fix for the fix to disable CET instrumentation generation for
kernel code. We forgot 32-bit, which we seem to do very often
nowadays
- A Xen PV fix to irqdomain init ordering"
* tag 'x86_urgent_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci: Create PCI/MSI irqdomain after x86_init.pci.arch_init()
x86/build: Disable CET instrumentation in the kernel for 32-bit too
x86/sgx: Maintain encl->refcount for each encl->mm_list entry
The leds-rt8515 driver can optionall use the v4l2 flash led class,
but it causes a link error when that class is in a loadable module
and the rt8515 driver itself is built-in:
ld.lld: error: undefined symbol: v4l2_flash_init
>>> referenced by leds-rt8515.c
>>> leds/flash/leds-rt8515.o:(rt8515_probe) in archive
drivers/built-in.a
Adding 'depends on V4L2_FLASH_LED_CLASS' in Kconfig would avoid that,
but it would make it impossible to use the driver without the
v4l2 support.
Add the same dependency that the other users of this class have
instead, which just prevents the broken configuration.
Fixes: e1c6edcbea ("leds: rt8515: Add Richtek RT8515 LED driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Uwe Kleine-König
Geert Uytterhoeven
Bartosz Golaszewski
Thierry Reding
Nobuhiro Iwamatsu
Aswath Govindraju
Matti Vaittinen
Lad Prabhakar
Zheng Yongjun
Jonathan Neuschäfer
Colin Ian King
Linus Torvalds
Arnd Bergmann
Rolf Eike Beer