This patch adds the device ID for the BCM4373A0 module, found e.g. in
the Infineon (Cypress) CYW4373E chip. The required firmware file is
named 'BCM4373A0.hcd'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are provedly different firmware variants for the different
phones using some of these chips. These were extracted from a few
Samsung phones:
37446 BCM4334B0.samsung,codina-tmo.hcd
37366 BCM4334B0.samsung,golden.hcd
37403 BCM4334B0.samsung,kyle.hcd
37366 BCM4334B0.samsung,skomer.hcd
This patch supports the above naming schedule with inserting
[.board_name] between the firmware name and ".hcd". This scheme
is the same as used by the companion BRCM wireless chips
as can be seen in
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
or just by looking at the firmwares in linux-firmware/brcm.
Currently we only support board variants using the device
tree compatible string as board type, but other schemes are
possible.
This makes it possible to successfully load a few unique
firmware variants for some Samsung phones.
Cc: phone-devel@vger.kernel.org
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth on the BCM43752 needs a patchram file to function correctly.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the BCM43430B0 module, found e.g. in
certain revisions of AMPAK AP6212 chip. The required firmware file is
named 'BCM43430B0.hcd'.
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for the BCM4324B5 and BCM20703A1 chipsets. This makes the code use just
"BCM" as prefix for the filename to pass to request-firmware, making it
harder for users to figure out which firmware they need. This especially
is problematic with the UART attached BCM4324B5 where this leads to the
filename being just "BCM.hcd".
Add the 2 missing devices to subver tables. This has been tested on:
1. A Dell XPS15 9550 where this makes btbcm.c try to load
"BCM20703A1-0a5c-6410.hcd" before it tries to load "BCM-0a5c-6410.hcd".
2. A Thinkpad 8 where this makes btbcm.c try to load
"BCM4324B5.hcd" before it tries to load "BCM.hcd"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for various newer chipsets. This makes the code use just "BCM" as prefix
for the filename to pass to request-firmware, making it harder for users
to figure out which firmware they need. This especially a problem with
UART attached devices where this leads to the filename being "BCM.hcd".
If we add new entries to the subver-tables now, then this will change
what firmware file the kernel looks for, e.g. currently linux-firmware
contains a brcm/BCM-0bb4-0306.hcd file. If we add the info for the
BCM20703A1 to the subver table, then this will change to
brcm/BCM20703A1-0bb4-0306.hcd. This will cause the file to no longer
get loaded breaking Bluetooth for existing users, going against the
no regressions policy.
To avoid this regression make the btbcm code try multiple filenames,
first try the fullname, e.g. BCM20703A1-0bb4-0306.hcd and if that is
not found, then fallback to the name with just BCM as prefix.
This commit also adds an info message which filename was used,
this makes the output look like this for example:
[ 57.387867] Bluetooth: hci0: BCM20703A1
[ 57.387870] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0000
[ 57.389438] Bluetooth: hci0: BCM20703A1 'brcm/BCM20703A1-0a5c-6410.hcd' Patch
[ 58.681769] Bluetooth: hci0: BCM20703A1 Generic USB 20Mhz fcbga_BU
[ 58.681772] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0481
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have already loaded the firmware/patchram and btbcm_initialize()
is called to re-init the HCI after this then there is no need to get
the USB device-ids and build a firmware-filename out of these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On UART attached devices we do:
1. btbcm_initialize()
2. Setup UART baudrate, etc.
3. btbcm_finalize()
After our previous changes we can now also use btbcm_finalize() from
the btbcm_setup_patchram() function used on USB devices without any
functional changes. This completes unifying the USB and UART paths
as much as possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make btbcm_initialize() get and print the device's local-name on re-init
too, this will make us also print the local-name after loading the
Patch on UART attached devices making things more consistent.
This also removes some code duplication from btbcm_setup_patchram()
and allows more code duplication removal there in a follow-up patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of having btbcm_initialize() fill a passed in fw_name buffer
and then have its callers use that to request the firmware + load
it into the HCI, make btbcm_initialize() do this itself the first
time it is called (its get called a second time to reset the HCI
after the firmware has been loaded).
This removes some code duplication and makes it easier for further
patches in this series to try more then 1 firmware filename.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_finalize() is currently only used by UART attached BCM devices.
Move the setting of the USE_BDADDR_PROPERTY quirk, which we only want
for UART attached devices to hci_bcm in preparation for using
btbcm_finalize() for USB attached devices too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_initialize() must either return an error; or fill the passed in
fw_name, otherwise we end up passing uninitialized stack memory to
request_firmware().
Since we have a fallback hw_name of "BCM" not having a known version
in the subver field does not matter, drop the check so that we always
fill the passed in fw_name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patches fixes two warnings of checkpatch.pl, both of the type
WARNING: Missing a blank line after declarations
Signed-off-by: Changqi Du <d.changqi@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add BCM vendor specific command to configure PCM parameters. The new
vendor opcode allows us to set the sco routing, the pcm interface rate,
and a few other pcm specific options (frame sync, sync mode, and clock
mode). See broadcom-bluetooth.txt in Documentation for more information
about valid values for those settings.
Here is an example trace where this opcode was used to configure
a BCM4354:
< HCI Command: Vendor (0x3f|0x001c) plen 5
01 02 00 01 01
> HCI Event: Command Complete (0x0e) plen 4
Vendor (0x3f|0x001c) ncmd 1
Status: Success (0x00)
We can read back the values as well with ocf 0x001d to confirm the
values that were set:
$ hcitool cmd 0x3f 0x001d
< HCI Command: ogf 0x3f, ocf 0x001d, plen 0
> HCI Event: 0x0e plen 9
01 1D FC 00 01 02 00 01 01
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some devices ship with the controller default address, like the
Orange Pi 3 (BCM4345C5).
Allow the bootloader to set a valid address through the device tree.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the device ID for the WiFi/BT/FM combo chip BCM4334 (rev B0).
The chip seems to use 43:34:b0:00:00:00 as default address,
so add it to the list of default addresses and leave it up
to the user to configure a valid one.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4359C0 BT/Wi-Fi compo chip needs an entry to be discovered
by the btbcm driver.
Tested using an AP6398S module from Ampak.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BCM2076B1 appears to use 20:76:A0:00:56:79 as default address.
This address is used by at least 5 devices with the AMPAK AP6476
module and is also suspicious because it starts with the chip name
2076 (followed by a different revision A0 for some reason).
Add it to the list of default addresses and leave it up to the
user to configure a valid one.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1)
used in the AMPAK AP6476 WiFi/BT/FM/GPS module.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tim Harvey
Linus Walleij
Aditya Garg
Angus Ainslie
Mikhail Rudenko
Azamat H. Hackimov
Hans de Goede
Changqi Du
Abhishek Pandit-Subedi
Andre Heider
Mohammad Rasim
Stephan Gerhold
Ondrej Jirman
Neil Armstrong
Thomas Gleixner