You've already forked flashfloppy
mirror of
https://github.com/Team-Resurgent/flashfloppy.git
synced 2026-04-30 10:49:33 -07:00
Keir Fraser
0351c481c0
Single quotes are not accepted by the parser, so the extra punctuation is unnecessary and confusing verbiage. Refs #865
292 lines
10 KiB
INI
292 lines
10 KiB
INI
## FF.CFG: Example FlashFloppy Configuration File
|
|
|
|
# Place in the root folder or FF/ subfolder of your USB drive.
|
|
# NOTE: If FF/ exists, IMG.CFG must reside there, not the root folder.
|
|
|
|
# Uncommented lines below are the default settings.
|
|
# Uncommented options cannot be overridden by settings in other config files.
|
|
|
|
##
|
|
## DRIVE EMULATION
|
|
|
|
# Floppy-drive interface mode (interface pins 2 and 34)
|
|
# jc: Specified by jumper JC (open: shugart, closed: ibmpc)
|
|
# shugart: P2=DSKCHG, P34=RDY (Amiga, Atari ST, many others)
|
|
# ibmpc: P2=unused, P34=DSKCHG (IBM PC interface)
|
|
# ibmpc-hdout: P2=HD_OUT, P34=DSKCHG (not generally needed: prefer ibmpc)
|
|
# jppc: P2=unused, P34=RDY (Japanese PC standard)
|
|
# jppc-hdout: P2=HD_OUT, P34=RDY (Japanese PC alternate: prefer jppc)
|
|
# akai-s950: Legacy alias of jppc-hdout, previously used for Akai S950
|
|
# amiga: P2=DSKCHG, P34=DRIVE_ID (not generally needed: prefer shugart)
|
|
interface = jc
|
|
|
|
# Host platform: Improves image-format detection for generic types such as IMG
|
|
# acorn: Acorn ADFS
|
|
# akai: Akai (S01, S20, S950), Korg, SC Prophet 3000
|
|
# casio: Casio (FZ-1)
|
|
# dec: DEC (RX33, RX50)
|
|
# ensoniq: Ensoniq (ASR, TS, etc)
|
|
# fluke: Fluke 9100
|
|
# gem: General Music (S2, S3)
|
|
# ibm-3174: IBM 3174 Establishment Controller
|
|
# memotech: Memotech
|
|
# msx: MSX
|
|
# nascom: Nascom
|
|
# pc98: NEC PC-98
|
|
# pc-dos: PC DOS Format (geometry determined from Bios Parameter Block)
|
|
# tandy-coco: Tandy Color Computer (CoCo)
|
|
# ti99: TI-99/4A
|
|
# uknc: UKNC / DVK Soviet PDP-11
|
|
# unspecified: Common default geometries (including IBM PC)
|
|
host = unspecified
|
|
|
|
# Pins 2 & 34 output (drive->host) manual configuration
|
|
# auto: Auto-configure from interface= setting
|
|
# nc: Unused/No Connection [eg. if pin is an input (host->drive) on your host]
|
|
# low: Always 0 volts (0v)
|
|
# high: Always 5 volts (5v)
|
|
# rdy: Drive ready (Ready = 0v)
|
|
# nrdy: Logical complement of above
|
|
# dens: Density mode (High Density = 0v)
|
|
# ndens: Logical complement of above
|
|
# chg: Disk changed (Changed = 0v)
|
|
# nchg: Logical complement of above
|
|
# Values: auto, nc, low, high, rdy, nrdy, dens, ndens, chg, nchg
|
|
pin02 = auto
|
|
pin34 = auto
|
|
|
|
# Forcibly write-protect images, or respect the FAT read-only attribute?
|
|
# Values: yes | no
|
|
write-protect = no
|
|
|
|
# Maximum cylinder that can be stepped to (255 is required for access to
|
|
# Direct Access mode as used by image-selector utilities and Autoswap games).
|
|
# Values: 0 <= N <= 255
|
|
max-cyl = 255
|
|
|
|
# Filter glitches in the SIDE-select signal shorter than N microseconds
|
|
# Values: 0 <= N <= 255
|
|
side-select-glitch-filter = 0
|
|
|
|
# Rotational offset of disk after a track change
|
|
# instant: No rotation during track change
|
|
# realtime: Emulate rotation of disk while track is changing
|
|
# Values: instant | realtime
|
|
track-change = instant
|
|
|
|
# Rotational offset of disk after draining a write to Flash
|
|
# instant: No rotation
|
|
# realtime: Disk rotates in real time during drain
|
|
# eot: Disk rotates to (near) end of track
|
|
# Values: instant | realtime | eot
|
|
write-drain = instant
|
|
|
|
# Index pulses suppressed when RDATA and WDATA inactive?
|
|
# Values: yes | no
|
|
index-suppression = yes
|
|
|
|
# Milliseconds from head-step start to RDATA active.
|
|
# Values: 0 <= N <= 255
|
|
head-settle-ms = 12
|
|
|
|
# Milliseconds delay from motor-on to drive ready.
|
|
# On a standard unmodified Gotek the motor signal is not connected and a
|
|
# non-default value here will have no effect. Most systems and software do
|
|
# not care about correct motor behaviour, and default (ignore) works fine.
|
|
# Values: ignore | 0 <= N <= 1000
|
|
motor-delay = ignore
|
|
|
|
# What causes the disk-change (chg) signal to reset after disk insertion?
|
|
# step: Step command received
|
|
# pa14: CHGRST (pin 1 on old Sony drives), connected to PA14 (JTCK/SWCLK)
|
|
# delay-N: Automatically after N*0.5sec (0 <= N <= 15)
|
|
chgrst = step
|
|
|
|
##
|
|
## STARTUP / INITIALISATION
|
|
|
|
# Disk image loaded or ejected at startup?
|
|
# Values: yes | no
|
|
ejected-on-startup = no
|
|
|
|
# Which image (or folder) is selected at startup?
|
|
# last: Last-selected item at power-off (recorded in IMAGE_A.CFG)
|
|
# static: Static path specified in INIT_A.CFG
|
|
# init: First item in root folder
|
|
# Values: last | static | init
|
|
image-on-startup = last
|
|
|
|
# Time in milliseconds to attempt to probe attached display.
|
|
# You may set this to 0 if you have a 2-digit LED display attached.
|
|
# Values: 0 <= N <= 65535
|
|
display-probe-ms = 3000
|
|
|
|
##
|
|
## IMAGE NAVIGATION
|
|
|
|
# Auto-select the current file after N seconds
|
|
# N=0: disable auto-select
|
|
# Values: 0 <= N <= 255
|
|
autoselect-file-secs = 2
|
|
|
|
# Auto-select the current folder after N seconds
|
|
# N=0: disable auto-select
|
|
# Values: 0 <= N <= 255
|
|
autoselect-folder-secs = 2
|
|
|
|
# Sorting of folder entries in native navigation mode.
|
|
# always: Always sort folder entries. Large folders may be truncated.
|
|
# never: Never sort folder entries, instead presenting them in FAT order.
|
|
# small: Only sort folders which are small enough to sort in full.
|
|
# Values: always | never | small
|
|
folder-sort = always
|
|
|
|
# Priority of files vs subfolders when sorting folder entries:
|
|
# folders: Folders listed before files
|
|
# files: Files listed before folders
|
|
# none: Files and folders are not differentiated
|
|
# Values: folders | files | none
|
|
sort-priority = folders
|
|
|
|
# Navigation mode for selecting images/slots
|
|
# native: Navigate through all valid images/dirs
|
|
# indexed: Navigate through DSKA0000, DSKA0001, ...
|
|
# default: native unless overridden by HxC-compat-mode config
|
|
nav-mode = default
|
|
|
|
# When navigating slots or folder, loop at min/max?
|
|
# Values: yes | no
|
|
nav-loop = yes
|
|
|
|
# Actions of first two buttons.
|
|
# B1 | B2 | Both
|
|
# zero: Prev | Next | Slot 0
|
|
# eject: Prev | Next | Eject/Insert
|
|
# htu: +10 | +1 | +100
|
|
# rotary: Up-dir | Select/Eject/Insert | -
|
|
# rotary-fast: Prev | Next | Up-dir [Prev/Next are accelerated]
|
|
# reverse: Reverse sense of B1 and B2
|
|
# Multiple values can be separated by commas, eg twobutton-action=eject,reverse
|
|
twobutton-action = zero
|
|
|
|
# Input sensor type at the rotary-encoder inputs (pins PC10 and PC11):
|
|
# [full | half | quarter]:
|
|
# Rotary encoder, identified by fraction of a Gray-code cycle performed
|
|
# per detent/click. If default value (full) requires multiple
|
|
# clicks/detents to move position then change to half (if 2 clicks
|
|
# per move) or quarter (if 4 clicks).
|
|
# [trackball]:
|
|
# Blackberry-style trackball (eg. using Hall-effect sensors).
|
|
# [buttons]:
|
|
# Push-to-ground Prev/Next buttons.
|
|
# [reverse]:
|
|
# If the input is working in reverse, use this option to swap directions.
|
|
# [v2]:
|
|
# Use the rotary encoder logic from FlashFloppy v2.x. Use this if the
|
|
# v3 logic is too strict and results in no, or missing, movements.
|
|
# Multiple values can be separated by commas, eg rotary=quarter,reverse
|
|
# Values: none | quarter | half | full | trackball | buttons | reverse | v2
|
|
rotary = full
|
|
|
|
# Prefix for image names in indexed navigation mode. String can be empty ("").
|
|
indexed-prefix = "DSKA"
|
|
|
|
##
|
|
## DISPLAY
|
|
|
|
# Display Type.
|
|
# auto: Auto-detect (7-seg LED, LCD, OLED)
|
|
# lcd-CCxRR: CCxRR backlit LCD with I2C backpack (16<=CC<=40, 02<=RR<=04)
|
|
# oled-128xNN: 128xNN I2C OLED (NN = 32 | 64)
|
|
# -rotate: OLED view is rotated 180 degrees
|
|
# -hflip: OLED view is flipped horizontally
|
|
# -narrow[er]: OLED view is restricted to Gotek display cutout
|
|
# (-narrow: 18 chars; -narrower: 16 chars)
|
|
# -inverse: Inverse/reverse video (black text on white background)
|
|
# -ztech: ZHONGJY_TECH 2.23" 128x32 SSD1305 OLED display
|
|
# -slow: Run I2C bus slower (use this if OLED regularly blanks/corrupts)
|
|
# Values: auto | lcd-CCxRR | oled-128xNN[-rotate][-narrow[er]]...
|
|
display-type = auto
|
|
|
|
# OLED Font. Narrow and wide options.
|
|
# Narrower 6x13 font permits:
|
|
# - More characters per row
|
|
# - Use of Gotek display cutout (eg. "display-type=oled-128x32-narrow")
|
|
# Values: 6x13 | 8x16
|
|
oled-font = 6x13
|
|
|
|
# OLED contrast/brightness.
|
|
# Values: 0 <= N <= 255
|
|
oled-contrast = 143
|
|
|
|
# Text height and arrangement on LCD/OLED and on OSD, respectively.
|
|
# Comma-separated list, one entry per display row, top down.
|
|
# Each list item is a digit plus optional height specifier: [0-7][d]
|
|
# content-row: 0-3 = specified content, 7 = blank
|
|
# 0: Current image name
|
|
# 1: Status
|
|
# 2: Image/Volume info
|
|
# 3: Current subfolder name
|
|
# height-specifier: d = double height (32px, OLED only; ignored for LCD)
|
|
# Default depends on display, eg.: oled-128x32 -> 0,1 ; oled-128x64 -> 3,0d,1
|
|
# Values: [0-7][d] | default
|
|
display-order = default
|
|
osd-display-order = default
|
|
|
|
# OSD text columns. This is currently respected only when no LCD/OLED is found.
|
|
# Values: 16 <= N <= 40
|
|
osd-columns = 40
|
|
|
|
# Turn an LCD or OLED display off after N seconds of inactivity
|
|
# N=0: always off; N=255: always on
|
|
# Values: 0 <= N <= 255
|
|
display-off-secs = 60
|
|
|
|
# Switch on LCD/OLED display when there is drive activity?
|
|
# yes: Trigger on track changes and disk writes
|
|
# sel: Trigger on drive select
|
|
# no: No automatic trigger
|
|
# Values: yes | sel | no
|
|
display-on-activity = yes
|
|
|
|
# LCD/OLED long filename scroll rate in milliseconds per update
|
|
# Values: 100 <= N <= 65535
|
|
display-scroll-rate = 200
|
|
|
|
# LCD/OLED pause time at start/end of scroll, in milliseconds
|
|
# Zero means endless scroll
|
|
# Values: 0 <= N <= 65535
|
|
display-scroll-pause = 2000
|
|
|
|
# LCD/OLED long filename scroll rate during navigation (ms per update)
|
|
# Values: 0 <= N <= 65535
|
|
nav-scroll-rate = 80
|
|
|
|
# LCD/OLED long filename pause before scroll, during navigation (milliseconds)
|
|
# Values: 0 <= N <= 65535
|
|
nav-scroll-pause = 300
|
|
|
|
##
|
|
## MISCELLANEOUS
|
|
|
|
# Speaker volume for head STEP
|
|
# Values: 0 <= N <= 20
|
|
step-volume = 10
|
|
|
|
# Speaker volume for insert, eject, and slot-number notifications.
|
|
# Slot number is indicated by a sequence of beeps when an image is mounted
|
|
# iff "slotnr" is specified. The slot number is then notified by a sequence of
|
|
# long beeps (each counting +5), followed by a sequence of short beeps
|
|
# (each counting +1).
|
|
# Values: N[,slotnr] (0 <= N <= 15)
|
|
notify-volume = 0
|
|
|
|
# Report the specified version number to host software
|
|
# Values: <quoted-string> ("" means report real version)
|
|
# eg. da-report-version = "v3.0.0.0"
|
|
da-report-version = ""
|
|
|
|
# Automatically extend certain types of truncated image file (SSD,DSD,TRD)?
|
|
# Values: yes | no
|
|
extend-image = yes
|