diff --git a/net/freeradius/src/opnsense/service/templates/OPNsense/Freeradius/radiusd.conf b/net/freeradius/src/opnsense/service/templates/OPNsense/Freeradius/radiusd.conf deleted file mode 100644 index 60c868988..000000000 --- a/net/freeradius/src/opnsense/service/templates/OPNsense/Freeradius/radiusd.conf +++ /dev/null @@ -1,830 +0,0 @@ -{% if helpers.exists('OPNsense.freeradius.general.enabled') and OPNsense.freeradius.general.enabled == '1' %} -{% raw %} -# -*- text -*- -## -## radiusd.conf -- FreeRADIUS server configuration file - 3.0.13 -## -## http://www.freeradius.org/ -## $Id: c62f4ffed53a073a885f243b728129f5c482fad7 $ -## - -###################################################################### -# -# Read "man radiusd" before editing this file. See the section -# titled DEBUGGING. It outlines a method where you can quickly -# obtain the configuration you want, without running into -# trouble. -# -# Run the server in debugging mode, and READ the output. -# -# $ radiusd -X -# -# We cannot emphasize this point strongly enough. The vast -# majority of problems can be solved by carefully reading the -# debugging output, which includes warnings about common issues, -# and suggestions for how they may be fixed. -# -# There may be a lot of output, but look carefully for words like: -# "warning", "error", "reject", or "failure". The messages there -# will usually be enough to guide you to a solution. -# -# If you are going to ask a question on the mailing list, then -# explain what you are trying to do, and include the output from -# debugging mode (radiusd -X). Failure to do so means that all -# of the responses to your question will be people telling you -# to "post the output of radiusd -X". - -###################################################################### -# -# The location of other config files and logfiles are declared -# in this file. -# -# Also general configuration for modules can be done in this -# file, it is exported through the API to modules that ask for -# it. -# -# See "man radiusd.conf" for documentation on the format of this -# file. Note that the individual configuration items are NOT -# documented in that "man" page. They are only documented here, -# in the comments. -# -# The "unlang" policy language can be used to create complex -# if / else policies. See "man unlang" for details. -# - -prefix = /usr/local -exec_prefix = ${prefix} -sysconfdir = ${prefix}/etc -localstatedir = /var -sbindir = ${exec_prefix}/sbin -logdir = /var/log -raddbdir = ${sysconfdir}/raddb -radacctdir = ${logdir}/radacct - -# -# name of the running server. See also the "-n" command-line option. -name = radiusd - -# Location of config and logfiles. -confdir = ${raddbdir} -modconfdir = ${confdir}/mods-config -certdir = ${confdir}/certs -cadir = ${confdir}/certs -run_dir = ${localstatedir}/run/${name} - -# Should likely be ${localstatedir}/lib/radiusd -db_dir = ${raddbdir} - -# -# libdir: Where to find the rlm_* modules. -# -# This should be automatically set at configuration time. -# -# If the server builds and installs, but fails at execution time -# with an 'undefined symbol' error, then you can use the libdir -# directive to work around the problem. -# -# The cause is usually that a library has been installed on your -# system in a place where the dynamic linker CANNOT find it. When -# executing as root (or another user), your personal environment MAY -# be set up to allow the dynamic linker to find the library. When -# executing as a daemon, FreeRADIUS MAY NOT have the same -# personalized configuration. -# -# To work around the problem, find out which library contains that symbol, -# and add the directory containing that library to the end of 'libdir', -# with a colon separating the directory names. NO spaces are allowed. -# -# e.g. libdir = /usr/local/lib:/opt/package/lib -# -# You can also try setting the LD_LIBRARY_PATH environment variable -# in a script which starts the server. -# -# If that does not work, then you can re-configure and re-build the -# server to NOT use shared libraries, via: -# -# ./configure --disable-shared -# make -# make install -# -libdir = /usr/local/lib/freeradius-3.0.13 - -# pidfile: Where to place the PID of the RADIUS server. -# -# The server may be signalled while it's running by using this -# file. -# -# This file is written when ONLY running in daemon mode. -# -# e.g.: kill -HUP `cat /var/run/radiusd/radiusd.pid` -# -pidfile = ${run_dir}/${name}.pid - -# -# correct_escapes: use correct backslash escaping -# -# Prior to version 3.0.5, the handling of backslashes was a little -# awkward, i.e. "wrong". In some cases, to get one backslash into -# a regex, you had to put 4 in the config files. -# -# Version 3.0.5 fixes that. However, for backwards compatibility, -# the new method of escaping is DISABLED BY DEFAULT. This means -# that upgrading to 3.0.5 won't break your configuration. -# -# If you don't have double backslashes (i.e. \\) in your configuration, -# this won't matter to you. If you do have them, fix that to use only -# one backslash, and then set "correct_escapes = true". -# -# You can check for this by doing: -# -# $ grep '\\\\' $(find raddb -type f -print) -# -correct_escapes = true - -# panic_action: Command to execute if the server dies unexpectedly. -# -# FOR PRODUCTION SYSTEMS, ACTIONS SHOULD ALWAYS EXIT. -# AN INTERACTIVE ACTION MEANS THE SERVER IS NOT RESPONDING TO REQUESTS. -# AN INTERACTICE ACTION MEANS THE SERVER WILL NOT RESTART. -# -# THE SERVER MUST NOT BE ALLOWED EXECUTE UNTRUSTED PANIC ACTION CODE -# PATTACH CAN BE USED AS AN ATTACK VECTOR. -# -# The panic action is a command which will be executed if the server -# receives a fatal, non user generated signal, i.e. SIGSEGV, SIGBUS, -# SIGABRT or SIGFPE. -# -# This can be used to start an interactive debugging session so -# that information regarding the current state of the server can -# be acquired. -# -# The following string substitutions are available: -# - %e The currently executing program e.g. /sbin/radiusd -# - %p The PID of the currently executing program e.g. 12345 -# -# Standard ${} substitutions are also allowed. -# -# An example panic action for opening an interactive session in GDB would be: -# -#panic_action = "gdb %e %p" -# -# Again, don't use that on a production system. -# -# An example panic action for opening an automated session in GDB would be: -# -#panic_action = "gdb -silent -x ${raddbdir}/panic.gdb %e %p 2>&1 | tee ${logdir}/gdb-${name}-%p.log" -# -# That command can be used on a production system. -# - -# max_request_time: The maximum time (in seconds) to handle a request. -# -# Requests which take more time than this to process may be killed, and -# a REJECT message is returned. -# -# WARNING: If you notice that requests take a long time to be handled, -# then this MAY INDICATE a bug in the server, in one of the modules -# used to handle a request, OR in your local configuration. -# -# This problem is most often seen when using an SQL database. If it takes -# more than a second or two to receive an answer from the SQL database, -# then it probably means that you haven't indexed the database. See your -# SQL server documentation for more information. -# -# Useful range of values: 5 to 120 -# -max_request_time = 30 - -# cleanup_delay: The time to wait (in seconds) before cleaning up -# a reply which was sent to the NAS. -# -# The RADIUS request is normally cached internally for a short period -# of time, after the reply is sent to the NAS. The reply packet may be -# lost in the network, and the NAS will not see it. The NAS will then -# re-send the request, and the server will respond quickly with the -# cached reply. -# -# If this value is set too low, then duplicate requests from the NAS -# MAY NOT be detected, and will instead be handled as separate requests. -# -# If this value is set too high, then the server will cache too many -# requests, and some new requests may get blocked. (See 'max_requests'.) -# -# Useful range of values: 2 to 10 -# -cleanup_delay = 5 - -# max_requests: The maximum number of requests which the server keeps -# track of. This should be 256 multiplied by the number of clients. -# e.g. With 4 clients, this number should be 1024. -# -# If this number is too low, then when the server becomes busy, -# it will not respond to any new requests, until the 'cleanup_delay' -# time has passed, and it has removed the old requests. -# -# If this number is set too high, then the server will use a bit more -# memory for no real benefit. -# -# If you aren't sure what it should be set to, it's better to set it -# too high than too low. Setting it to 1000 per client is probably -# the highest it should be. -# -# Useful range of values: 256 to infinity -# -max_requests = 16384 - -# hostname_lookups: Log the names of clients or just their IP addresses -# e.g., www.freeradius.org (on) or 206.47.27.232 (off). -# -# The default is 'off' because it would be overall better for the net -# if people had to knowingly turn this feature on, since enabling it -# means that each client request will result in AT LEAST one lookup -# request to the nameserver. Enabling hostname_lookups will also -# mean that your server may stop randomly for 30 seconds from time -# to time, if the DNS requests take too long. -# -# Turning hostname lookups off also means that the server won't block -# for 30 seconds, if it sees an IP address which has no name associated -# with it. -# -# allowed values: {no, yes} -# -hostname_lookups = no - -# -# Logging section. The various "log_*" configuration items -# will eventually be moved here. -# -log { - # - # Destination for log messages. This can be one of: - # - # files - log to "file", as defined below. - # syslog - to syslog (see also the "syslog_facility", below. - # stdout - standard output - # stderr - standard error. - # - # The command-line option "-X" over-rides this option, and forces - # logging to go to stdout. - # - destination = files - - # - # Highlight important messages sent to stderr and stdout. - # - # Option will be ignored (disabled) if output if TERM is not - # an xterm or output is not to a TTY. - # - colourise = yes - - # - # The logging messages for the server are appended to the - # tail of this file if destination == "files" - # - # If the server is running in debugging mode, this file is - # NOT used. - # - file = ${logdir}/radius.log - - # - # If this configuration parameter is set, then log messages for - # a *request* go to this file, rather than to radius.log. - # - # i.e. This is a log file per request, once the server has accepted - # the request as being from a valid client. Messages that are - # not associated with a request still go to radius.log. - # - # Not all log messages in the server core have been updated to use - # this new internal API. As a result, some messages will still - # go to radius.log. Please submit patches to fix this behavior. - # - # The file name is expanded dynamically. You should ONLY user - # server-side attributes for the filename (e.g. things you control). - # Using this feature MAY also slow down the server substantially, - # especially if you do thinks like SQL calls as part of the - # expansion of the filename. - # - # The name of the log file should use attributes that don't change - # over the lifetime of a request, such as User-Name, - # Virtual-Server or Packet-Src-IP-Address. Otherwise, the log - # messages will be distributed over multiple files. - # - # Logging can be enabled for an individual request by a special - # dynamic expansion macro: %{debug: 1}, where the debug level - # for this request is set to '1' (or 2, 3, etc.). e.g. - # - # ... - # update control { - # Tmp-String-0 = "%{debug:1}" - # } - # ... - # - # The attribute that the value is assigned to is unimportant, - # and should be a "throw-away" attribute with no side effects. - # - #requests = ${logdir}/radiusd-%{%{Virtual-Server}:-DEFAULT}-%Y%m%d.log - - # - # Which syslog facility to use, if ${destination} == "syslog" - # - # The exact values permitted here are OS-dependent. You probably - # don't want to change this. - # - syslog_facility = daemon - - # Log the full User-Name attribute, as it was found in the request. - # - # allowed values: {no, yes} - # - stripped_names = no - - # Log authentication requests to the log file. - # - # allowed values: {no, yes} - # - auth = no - - # Log passwords with the authentication requests. - # auth_badpass - logs password if it's rejected - # auth_goodpass - logs password if it's correct - # - # allowed values: {no, yes} - # - auth_badpass = no - auth_goodpass = no - - # Log additional text at the end of the "Login OK" messages. - # for these to work, the "auth" and "auth_goodpass" or "auth_badpass" - # configurations above have to be set to "yes". - # - # The strings below are dynamically expanded, which means that - # you can put anything you want in them. However, note that - # this expansion can be slow, and can negatively impact server - # performance. - # -# msg_goodpass = "" -# msg_badpass = "" - - # The message when the user exceeds the Simultaneous-Use limit. - # - msg_denied = "You are already logged in - access denied" -} - -# The program to execute to do concurrency checks. -checkrad = ${sbindir}/checkrad - -# SECURITY CONFIGURATION -# -# There may be multiple methods of attacking on the server. This -# section holds the configuration items which minimize the impact -# of those attacks -# -security { - # chroot: directory where the server does "chroot". - # - # The chroot is done very early in the process of starting - # the server. After the chroot has been performed it - # switches to the "user" listed below (which MUST be - # specified). If "group" is specified, it switches to that - # group, too. Any other groups listed for the specified - # "user" in "/etc/group" are also added as part of this - # process. - # - # The current working directory (chdir / cd) is left - # *outside* of the chroot until all of the modules have been - # initialized. This allows the "raddb" directory to be left - # outside of the chroot. Once the modules have been - # initialized, it does a "chdir" to ${logdir}. This means - # that it should be impossible to break out of the chroot. - # - # If you are worried about security issues related to this - # use of chdir, then simply ensure that the "raddb" directory - # is inside of the chroot, end be sure to do "cd raddb" - # BEFORE starting the server. - # - # If the server is statically linked, then the only files - # that have to exist in the chroot are ${run_dir} and - # ${logdir}. If you do the "cd raddb" as discussed above, - # then the "raddb" directory has to be inside of the chroot - # directory, too. - # -# chroot = /path/to/chroot/directory - - # user/group: The name (or #number) of the user/group to run radiusd as. - # - # If these are commented out, the server will run as the - # user/group that started it. In order to change to a - # different user/group, you MUST be root ( or have root - # privileges ) to start the server. - # - # We STRONGLY recommend that you run the server with as few - # permissions as possible. That is, if you're not using - # shadow passwords, the user and group items below should be - # set to radius'. - # - # NOTE that some kernels refuse to setgid(group) when the - # value of (unsigned)group is above 60000; don't use group - # "nobody" on these systems! - # - # On systems with shadow passwords, you might have to set - # 'group = shadow' for the server to be able to read the - # shadow password file. If you can authenticate users while - # in debug mode, but not in daemon mode, it may be that the - # debugging mode server is running as a user that can read - # the shadow info, and the user listed below can not. - # - # The server will also try to use "initgroups" to read - # /etc/groups. It will join all groups where "user" is a - # member. This can allow for some finer-grained access - # controls. - # -# user = radius -# group = radius - - # Core dumps are a bad thing. This should only be set to - # 'yes' if you're debugging a problem with the server. - # - # allowed values: {no, yes} - # - allow_core_dumps = no - - # - # max_attributes: The maximum number of attributes - # permitted in a RADIUS packet. Packets which have MORE - # than this number of attributes in them will be dropped. - # - # If this number is set too low, then no RADIUS packets - # will be accepted. - # - # If this number is set too high, then an attacker may be - # able to send a small number of packets which will cause - # the server to use all available memory on the machine. - # - # Setting this number to 0 means "allow any number of attributes" - max_attributes = 200 - - # - # reject_delay: When sending an Access-Reject, it can be - # delayed for a few seconds. This may help slow down a DoS - # attack. It also helps to slow down people trying to brute-force - # crack a users password. - # - # Setting this number to 0 means "send rejects immediately" - # - # If this number is set higher than 'cleanup_delay', then the - # rejects will be sent at 'cleanup_delay' time, when the request - # is deleted from the internal cache of requests. - # - # As of Version 3.0.5, "reject_delay" has sub-second resolution. - # e.g. "reject_delay = 1.4" seconds is possible. - # - # Useful ranges: 1 to 5 - reject_delay = 1 - - # - # status_server: Whether or not the server will respond - # to Status-Server requests. - # - # When sent a Status-Server message, the server responds with - # an Access-Accept or Accounting-Response packet. - # - # This is mainly useful for administrators who want to "ping" - # the server, without adding test users, or creating fake - # accounting packets. - # - # It's also useful when a NAS marks a RADIUS server "dead". - # The NAS can periodically "ping" the server with a Status-Server - # packet. If the server responds, it must be alive, and the - # NAS can start using it for real requests. - # - # See also raddb/sites-available/status - # - status_server = yes - - # - # allow_vulnerable_openssl: Allow the server to start with - # versions of OpenSSL known to have critical vulnerabilities. - # - # This check is based on the version number reported by libssl - # and may not reflect patches applied to libssl by - # distribution maintainers. - # - allow_vulnerable_openssl = no -} - -# PROXY CONFIGURATION -# -# proxy_requests: Turns proxying of RADIUS requests on or off. -# -# The server has proxying turned on by default. If your system is NOT -# set up to proxy requests to another server, then you can turn proxying -# off here. This will save a small amount of resources on the server. -# -# If you have proxying turned off, and your configuration files say -# to proxy a request, then an error message will be logged. -# -# To disable proxying, change the "yes" to "no", and comment the -# $INCLUDE line. -# -# allowed values: {no, yes} -# -proxy_requests = yes -$INCLUDE proxy.conf - - -# CLIENTS CONFIGURATION -# -# Client configuration is defined in "clients.conf". -# - -# The 'clients.conf' file contains all of the information from the old -# 'clients' and 'naslist' configuration files. We recommend that you -# do NOT use 'client's or 'naslist', although they are still -# supported. -# -# Anything listed in 'clients.conf' will take precedence over the -# information from the old-style configuration files. -# -$INCLUDE clients.conf - - -# THREAD POOL CONFIGURATION -# -# The thread pool is a long-lived group of threads which -# take turns (round-robin) handling any incoming requests. -# -# You probably want to have a few spare threads around, -# so that high-load situations can be handled immediately. If you -# don't have any spare threads, then the request handling will -# be delayed while a new thread is created, and added to the pool. -# -# You probably don't want too many spare threads around, -# otherwise they'll be sitting there taking up resources, and -# not doing anything productive. -# -# The numbers given below should be adequate for most situations. -# -thread pool { - # Number of servers to start initially --- should be a reasonable - # ballpark figure. - start_servers = 5 - - # Limit on the total number of servers running. - # - # If this limit is ever reached, clients will be LOCKED OUT, so it - # should NOT BE SET TOO LOW. It is intended mainly as a brake to - # keep a runaway server from taking the system with it as it spirals - # down... - # - # You may find that the server is regularly reaching the - # 'max_servers' number of threads, and that increasing - # 'max_servers' doesn't seem to make much difference. - # - # If this is the case, then the problem is MOST LIKELY that - # your back-end databases are taking too long to respond, and - # are preventing the server from responding in a timely manner. - # - # The solution is NOT do keep increasing the 'max_servers' - # value, but instead to fix the underlying cause of the - # problem: slow database, or 'hostname_lookups=yes'. - # - # For more information, see 'max_request_time', above. - # - max_servers = 32 - - # Server-pool size regulation. Rather than making you guess - # how many servers you need, FreeRADIUS dynamically adapts to - # the load it sees, that is, it tries to maintain enough - # servers to handle the current load, plus a few spare - # servers to handle transient load spikes. - # - # It does this by periodically checking how many servers are - # waiting for a request. If there are fewer than - # min_spare_servers, it creates a new spare. If there are - # more than max_spare_servers, some of the spares die off. - # The default values are probably OK for most sites. - # - min_spare_servers = 3 - max_spare_servers = 10 - - # When the server receives a packet, it places it onto an - # internal queue, where the worker threads (configured above) - # pick it up for processing. The maximum size of that queue - # is given here. - # - # When the queue is full, any new packets will be silently - # discarded. - # - # The most common cause of the queue being full is that the - # server is dependent on a slow database, and it has received - # a large "spike" of traffic. When that happens, there is - # very little you can do other than make sure the server - # receives less traffic, or make sure that the database can - # handle the load. - # -# max_queue_size = 65536 - - # There may be memory leaks or resource allocation problems with - # the server. If so, set this value to 300 or so, so that the - # resources will be cleaned up periodically. - # - # This should only be necessary if there are serious bugs in the - # server which have not yet been fixed. - # - # '0' is a special value meaning 'infinity', or 'the servers never - # exit' - max_requests_per_server = 0 - - # Automatically limit the number of accounting requests. - # This configuration item tracks how many requests per second - # the server can handle. It does this by tracking the - # packets/s received by the server for processing, and - # comparing that to the packets/s handled by the child - # threads. - # - - # If the received PPS is larger than the processed PPS, *and* - # the queue is more than half full, then new accounting - # requests are probabilistically discarded. This lowers the - # number of packets that the server needs to process. Over - # time, the server will "catch up" with the traffic. - # - # Throwing away accounting packets is usually safe and low - # impact. The NAS will retransmit them in a few seconds, or - # even a few minutes. Vendors should read RFC 5080 Section 2.2.1 - # to see how accounting packets should be retransmitted. Using - # any other method is likely to cause network meltdowns. - # - auto_limit_acct = no -} - -###################################################################### -# -# SNMP notifications. Uncomment the following line to enable -# snmptraps. Note that you MUST also configure the full path -# to the "snmptrap" command in the "trigger.conf" file. -# -#$INCLUDE trigger.conf - -# MODULE CONFIGURATION -# -# The names and configuration of each module is located in this section. -# -# After the modules are defined here, they may be referred to by name, -# in other sections of this configuration file. -# -modules { - # - # Each module has a configuration as follows: - # - # name [ instance ] { - # config_item = value - # ... - # } - # - # The 'name' is used to load the 'rlm_name' library - # which implements the functionality of the module. - # - # The 'instance' is optional. To have two different instances - # of a module, it first must be referred to by 'name'. - # The different copies of the module are then created by - # inventing two 'instance' names, e.g. 'instance1' and 'instance2' - # - # The instance names can then be used in later configuration - # INSTEAD of the original 'name'. See the 'radutmp' configuration - # for an example. - # - - # - # As of 3.0, modules are in mods-enabled/. Files matching - # the regex /[a-zA-Z0-9_.]+/ are loaded. The modules are - # initialized ONLY if they are referenced in a processing - # section, such as authorize, authenticate, accounting, - # pre/post-proxy, etc. - # - $INCLUDE mods-enabled/ -} - -# Instantiation -# -# This section orders the loading of the modules. Modules -# listed here will get loaded BEFORE the later sections like -# authorize, authenticate, etc. get examined. -# -# This section is not strictly needed. When a section like -# authorize refers to a module, it's automatically loaded and -# initialized. However, some modules may not be listed in any -# of the following sections, so they can be listed here. -# -# Also, listing modules here ensures that you have control over -# the order in which they are initialized. If one module needs -# something defined by another module, you can list them in order -# here, and ensure that the configuration will be OK. -# -# After the modules listed here have been loaded, all of the modules -# in the "mods-enabled" directory will be loaded. Loading the -# "mods-enabled" directory means that unlike Version 2, you usually -# don't need to list modules here. -# -instantiate { - # - # We list the counter module here so that it registers - # the check_name attribute before any module which sets - # it -# daily - - # subsections here can be thought of as "virtual" modules. - # - # e.g. If you have two redundant SQL servers, and you want to - # use them in the authorize and accounting sections, you could - # place a "redundant" block in each section, containing the - # exact same text. Or, you could uncomment the following - # lines, and list "redundant_sql" in the authorize and - # accounting sections. - # - # The "virtual" module defined here can also be used with - # dynamic expansions, under a few conditions: - # - # * The section is "redundant", or "load-balance", or - # "redundant-load-balance" - # * The section contains modules ONLY, and no sub-sections - # * all modules in the section are using the same rlm_ - # driver, e.g. They are all sql, or all ldap, etc. - # - # When those conditions are satisfied, the server will - # automatically register a dynamic expansion, using the - # name of the "virtual" module. In the example below, - # it will be "redundant_sql". You can then use this expansion - # just like any other: - # - # update reply { - # Filter-Id := "%{redundant_sql: ... }" - # } - # - # In this example, the expansion is done via module "sql1", - # and if that expansion fails, using module "sql2". - # - # For best results, configure the "pool" subsection of the - # module so that "retry_delay" is non-zero. That will allow - # the redundant block to quickly ignore all "down" SQL - # databases. If instead we have "retry_delay = 0", then - # every time the redundant block is used, the server will try - # to open a connection to every "down" database, causing - # problems. - # - #redundant redundant_sql { - # sql1 - # sql2 - #} -} - -###################################################################### -# -# Policies are virtual modules, similar to those defined in the -# "instantiate" section above. -# -# Defining a policy in one of the policy.d files means that it can be -# referenced in multiple places as a *name*, rather than as a series of -# conditions to match, and actions to take. -# -# Policies are something like subroutines in a normal language, but -# they cannot be called recursively. They MUST be defined in order. -# If policy A calls policy B, then B MUST be defined before A. -# -###################################################################### -policy { - $INCLUDE policy.d/ -} - -###################################################################### -# -# Load virtual servers. -# -# This next $INCLUDE line loads files in the directory that -# match the regular expression: /[a-zA-Z0-9_.]+/ -# -# It allows you to define new virtual servers simply by placing -# a file into the raddb/sites-enabled/ directory. -# -$INCLUDE sites-enabled/ - -###################################################################### -# -# All of the other configuration sections like "authorize {}", -# "authenticate {}", "accounting {}", have been moved to the -# the file: -# -# raddb/sites-available/default -# -# This is the "default" virtual server that has the same -# configuration as in version 1.0.x and 1.1.x. The default -# installation enables this virtual server. You should -# edit it to create policies for your local site. -# -# For more documentation on virtual servers, see: -# -# raddb/sites-available/README -# -###################################################################### -{% endraw %} -{% endif %}