6.3 KiB
Base PoE
SKU:K012-C
Description
Base PoE is an M5 Base that implements a W5500 Ethernet controller chip with PoE module, which provides Hardwired TCP/IP embedded Ethernet control to facilitate easier internet connection to embedded systems. W5500 integrates TCP/IP protocol stack, 10/100M Ethernet data link layer (MAC) and physical layer (PHY).This base supports RS485 / RS232 communication and can be used as an Ethernet to serial port server. It is specifically designed for industrial applications. PoE (Power over Ethernet) technology is supported. Through the built-in PoE module, power can be directly supplied to the base through PoE hub / switch without a separate power supply. It comes with a couple of HT3.96 connectors, metal rail and magnet discs for easy installation. The 6 pins of the HT3.96 connector are spare, you can wire them up with an RS485 or RS232 adapter board as you like.
The figure below shows the internals of the LAN base
If you need to add an RS485 or RS232 interface, make sure to solder the RS485 or RS232 board onto the main board pin correspondingly.
Product Features
- Support PoE IEEE802.3 AF
- DC input supply voltage: 9-24V
- Ethernet access
- HT3.96 port for supporting RS485/RS232 communication
- 8 independent hardware socket simultaneous communication
- Support TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE protocols
- Support integrated 10BaseT / 100Base-T Ethernet PHY
- Easy to fixed on the wall
Applications
- Ethernet controller
- Ethernet and RS485/RS232 data forwarding
- Ethernet network node
Include
- 1x PoE Base
- 1x TTL-to-RS485 adapter board
- 1x TTL-to-RS232 adapter board
- 1x pin header 20pin
- 1x metal rails and magnet discs
- 3x HT3.96 terminal
- 2x 3pin
- 1x 4pin
- 10x cold crimp terminal（red Copper Lugs）
- 3x Allen wrench - 1x 1.5mm - 1x 2mm - 1x 2.5mm
- 2x hexagon socket head cap screws M3x28
- 4x hexagon socket tapping screw KA2x4
- 1x countersunk head screw M3x8
Specification
| Resources | Parameter |
| Ethernet chip | W5500 |
| Support protocols | TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE |
| RS485 chip | SP3485EE |
| RS232 chip | MAX232 |
| PoE power supply mode | Idle network cable pin power supply(10M/100M Ethernet)，J4&J5(VC-),J7&J8(VC+) |
| PoE specification | IEEE802.3 AF |
| DC input voltage | 9V~24V |
| Net weight | 32g |
| Gross weight | 132g |
| Product size | 54*54*28mm |
| Package Size | 105*65*40mm |
EasyLoader
EasyLoader is a concise and fast program writer, which has a built-in case program related to the product. It can be burned to the main control by simple steps to perform a series of function verification. Please install the corresponding driver according to the device type. M5Core host Please click here to view the CP210X driver installation tutorial, M5StickC/V/T/ATOM series can be used without driver)
Description:
Send messages or commands via Ethernet to control M5Stack 6060 PUSH or display messages on the screen
PinMap
| M5Stack | GPIO13 | GPIO18 | GPIO19 | GPIO23 | GPIO26 | GPIO34 | GPIO5 | GPIO15 |
|---|---|---|---|---|---|---|---|---|
| W5500 PoE | RST | CLK | MISO | MOSI | CS | INT | RX | TX |
Right side M-BUS pin definition
Schematic
Related Link
Example
- Get Arduino code click here